diff --git a/drivers/iio/gyro/adis16260.c b/drivers/iio/gyro/adis16260.c
new file mode 100644
index 0000000..7da8825
--- /dev/null
+++ b/drivers/iio/gyro/adis16260.c
@@ -0,0 +1,447 @@
+/*
+ * ADIS16260/ADIS16265 Programmable Digital Gyroscope Sensor Driver
+ *
+ * Copyright 2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mutex.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/spi/spi.h>
+#include <linux/sysfs.h>
+#include <linux/module.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/imu/adis.h>
+
+#define ADIS16260_STARTUP_DELAY	220 /* ms */
+
+#define ADIS16260_FLASH_CNT  0x00 /* Flash memory write count */
+#define ADIS16260_SUPPLY_OUT 0x02 /* Power supply measurement */
+#define ADIS16260_GYRO_OUT   0x04 /* X-axis gyroscope output */
+#define ADIS16260_AUX_ADC    0x0A /* analog input channel measurement */
+#define ADIS16260_TEMP_OUT   0x0C /* internal temperature measurement */
+#define ADIS16260_ANGL_OUT   0x0E /* angle displacement */
+#define ADIS16260_GYRO_OFF   0x14 /* Calibration, offset/bias adjustment */
+#define ADIS16260_GYRO_SCALE 0x16 /* Calibration, scale adjustment */
+#define ADIS16260_ALM_MAG1   0x20 /* Alarm 1 magnitude/polarity setting */
+#define ADIS16260_ALM_MAG2   0x22 /* Alarm 2 magnitude/polarity setting */
+#define ADIS16260_ALM_SMPL1  0x24 /* Alarm 1 dynamic rate of change setting */
+#define ADIS16260_ALM_SMPL2  0x26 /* Alarm 2 dynamic rate of change setting */
+#define ADIS16260_ALM_CTRL   0x28 /* Alarm control */
+#define ADIS16260_AUX_DAC    0x30 /* Auxiliary DAC data */
+#define ADIS16260_GPIO_CTRL  0x32 /* Control, digital I/O line */
+#define ADIS16260_MSC_CTRL   0x34 /* Control, data ready, self-test settings */
+#define ADIS16260_SMPL_PRD   0x36 /* Control, internal sample rate */
+#define ADIS16260_SENS_AVG   0x38 /* Control, dynamic range, filtering */
+#define ADIS16260_SLP_CNT    0x3A /* Control, sleep mode initiation */
+#define ADIS16260_DIAG_STAT  0x3C /* Diagnostic, error flags */
+#define ADIS16260_GLOB_CMD   0x3E /* Control, global commands */
+#define ADIS16260_LOT_ID1    0x52 /* Lot Identification Code 1 */
+#define ADIS16260_LOT_ID2    0x54 /* Lot Identification Code 2 */
+#define ADIS16260_PROD_ID    0x56 /* Product identifier;
+				   * convert to decimal = 16,265/16,260 */
+#define ADIS16260_SERIAL_NUM 0x58 /* Serial number */
+
+#define ADIS16260_ERROR_ACTIVE			(1<<14)
+#define ADIS16260_NEW_DATA			(1<<15)
+
+/* MSC_CTRL */
+#define ADIS16260_MSC_CTRL_MEM_TEST		(1<<11)
+/* Internal self-test enable */
+#define ADIS16260_MSC_CTRL_INT_SELF_TEST	(1<<10)
+#define ADIS16260_MSC_CTRL_NEG_SELF_TEST	(1<<9)
+#define ADIS16260_MSC_CTRL_POS_SELF_TEST	(1<<8)
+#define ADIS16260_MSC_CTRL_DATA_RDY_EN		(1<<2)
+#define ADIS16260_MSC_CTRL_DATA_RDY_POL_HIGH	(1<<1)
+#define ADIS16260_MSC_CTRL_DATA_RDY_DIO2	(1<<0)
+
+/* SMPL_PRD */
+/* Time base (tB): 0 = 1.953 ms, 1 = 60.54 ms */
+#define ADIS16260_SMPL_PRD_TIME_BASE	(1<<7)
+#define ADIS16260_SMPL_PRD_DIV_MASK	0x7F
+
+/* SLP_CNT */
+#define ADIS16260_SLP_CNT_POWER_OFF     0x80
+
+/* DIAG_STAT */
+#define ADIS16260_DIAG_STAT_ALARM2	(1<<9)
+#define ADIS16260_DIAG_STAT_ALARM1	(1<<8)
+#define ADIS16260_DIAG_STAT_FLASH_CHK_BIT	6
+#define ADIS16260_DIAG_STAT_SELF_TEST_BIT	5
+#define ADIS16260_DIAG_STAT_OVERFLOW_BIT	4
+#define ADIS16260_DIAG_STAT_SPI_FAIL_BIT	3
+#define ADIS16260_DIAG_STAT_FLASH_UPT_BIT	2
+#define ADIS16260_DIAG_STAT_POWER_HIGH_BIT	1
+#define ADIS16260_DIAG_STAT_POWER_LOW_BIT	0
+
+/* GLOB_CMD */
+#define ADIS16260_GLOB_CMD_SW_RESET	(1<<7)
+#define ADIS16260_GLOB_CMD_FLASH_UPD	(1<<3)
+#define ADIS16260_GLOB_CMD_DAC_LATCH	(1<<2)
+#define ADIS16260_GLOB_CMD_FAC_CALIB	(1<<1)
+#define ADIS16260_GLOB_CMD_AUTO_NULL	(1<<0)
+
+#define ADIS16260_SPI_SLOW	(u32)(300 * 1000)
+#define ADIS16260_SPI_BURST	(u32)(1000 * 1000)
+#define ADIS16260_SPI_FAST	(u32)(2000 * 1000)
+
+/* At the moment triggers are only used for ring buffer
+ * filling. This may change!
+ */
+
+#define ADIS16260_SCAN_GYRO	0
+#define ADIS16260_SCAN_SUPPLY	1
+#define ADIS16260_SCAN_AUX_ADC	2
+#define ADIS16260_SCAN_TEMP	3
+#define ADIS16260_SCAN_ANGL	4
+
+struct adis16260_chip_info {
+	unsigned int gyro_max_val;
+	unsigned int gyro_max_scale;
+	const struct iio_chan_spec *channels;
+	unsigned int num_channels;
+};
+
+struct adis16260 {
+	const struct adis16260_chip_info *info;
+
+	struct adis adis;
+};
+
+enum adis16260_type {
+	ADIS16251,
+	ADIS16260,
+	ADIS16266,
+};
+
+static const struct iio_chan_spec adis16260_channels[] = {
+	ADIS_GYRO_CHAN(X, ADIS16260_GYRO_OUT, ADIS16260_SCAN_GYRO,
+		BIT(IIO_CHAN_INFO_CALIBBIAS) |
+		BIT(IIO_CHAN_INFO_CALIBSCALE),
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 14),
+	ADIS_INCLI_CHAN(X, ADIS16260_ANGL_OUT, ADIS16260_SCAN_ANGL, 0,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 14),
+	ADIS_TEMP_CHAN(ADIS16260_TEMP_OUT, ADIS16260_SCAN_TEMP,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 12),
+	ADIS_SUPPLY_CHAN(ADIS16260_SUPPLY_OUT, ADIS16260_SCAN_SUPPLY,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 12),
+	ADIS_AUX_ADC_CHAN(ADIS16260_AUX_ADC, ADIS16260_SCAN_AUX_ADC,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 12),
+	IIO_CHAN_SOFT_TIMESTAMP(5),
+};
+
+static const struct iio_chan_spec adis16266_channels[] = {
+	ADIS_GYRO_CHAN(X, ADIS16260_GYRO_OUT, ADIS16260_SCAN_GYRO,
+		BIT(IIO_CHAN_INFO_CALIBBIAS) |
+		BIT(IIO_CHAN_INFO_CALIBSCALE),
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 14),
+	ADIS_TEMP_CHAN(ADIS16260_TEMP_OUT, ADIS16260_SCAN_TEMP,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 12),
+	ADIS_SUPPLY_CHAN(ADIS16260_SUPPLY_OUT, ADIS16260_SCAN_SUPPLY,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 12),
+	ADIS_AUX_ADC_CHAN(ADIS16260_AUX_ADC, ADIS16260_SCAN_AUX_ADC,
+		BIT(IIO_CHAN_INFO_SAMP_FREQ), 12),
+	IIO_CHAN_SOFT_TIMESTAMP(4),
+};
+
+static const struct adis16260_chip_info adis16260_chip_info_table[] = {
+	[ADIS16251] = {
+		.gyro_max_scale = 80,
+		.gyro_max_val = IIO_RAD_TO_DEGREE(4368),
+		.channels = adis16260_channels,
+		.num_channels = ARRAY_SIZE(adis16260_channels),
+	},
+	[ADIS16260] = {
+		.gyro_max_scale = 320,
+		.gyro_max_val = IIO_RAD_TO_DEGREE(4368),
+		.channels = adis16260_channels,
+		.num_channels = ARRAY_SIZE(adis16260_channels),
+	},
+	[ADIS16266] = {
+		.gyro_max_scale = 14000,
+		.gyro_max_val = IIO_RAD_TO_DEGREE(3357),
+		.channels = adis16266_channels,
+		.num_channels = ARRAY_SIZE(adis16266_channels),
+	},
+};
+
+/* Power down the device */
+static int adis16260_stop_device(struct iio_dev *indio_dev)
+{
+	struct adis16260 *adis16260 = iio_priv(indio_dev);
+	int ret;
+	u16 val = ADIS16260_SLP_CNT_POWER_OFF;
+
+	ret = adis_write_reg_16(&adis16260->adis, ADIS16260_SLP_CNT, val);
+	if (ret)
+		dev_err(&indio_dev->dev, "problem with turning device off: SLP_CNT");
+
+	return ret;
+}
+
+static const u8 adis16260_addresses[][2] = {
+	[ADIS16260_SCAN_GYRO] = { ADIS16260_GYRO_OFF, ADIS16260_GYRO_SCALE },
+};
+
+static int adis16260_read_raw(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan,
+			      int *val, int *val2,
+			      long mask)
+{
+	struct adis16260 *adis16260 = iio_priv(indio_dev);
+	const struct adis16260_chip_info *info = adis16260->info;
+	struct adis *adis = &adis16260->adis;
+	int ret;
+	u8 addr;
+	s16 val16;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		return adis_single_conversion(indio_dev, chan,
+				ADIS16260_ERROR_ACTIVE, val);
+	case IIO_CHAN_INFO_SCALE:
+		switch (chan->type) {
+		case IIO_ANGL_VEL:
+			*val = info->gyro_max_scale;
+			*val2 = info->gyro_max_val;
+			return IIO_VAL_FRACTIONAL;
+		case IIO_INCLI:
+			*val = 0;
+			*val2 = IIO_DEGREE_TO_RAD(36630);
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_VOLTAGE:
+			if (chan->channel == 0) {
+				*val = 1;
+				*val2 = 831500; /* 1.8315 mV */
+			} else {
+				*val = 0;
+				*val2 = 610500; /* 610.5 uV */
+			}
+			return IIO_VAL_INT_PLUS_MICRO;
+		case IIO_TEMP:
+			*val = 145;
+			*val2 = 300000; /* 0.1453 C */
+			return IIO_VAL_INT_PLUS_MICRO;
+		default:
+			return -EINVAL;
+		}
+	case IIO_CHAN_INFO_OFFSET:
+		*val = 250000 / 1453; /* 25 C = 0x00 */
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_CALIBBIAS:
+		addr = adis16260_addresses[chan->scan_index][0];
+		ret = adis_read_reg_16(adis, addr, &val16);
+		if (ret)
+			return ret;
+
+		*val = sign_extend32(val16, 11);
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_CALIBSCALE:
+		addr = adis16260_addresses[chan->scan_index][1];
+		ret = adis_read_reg_16(adis, addr, &val16);
+		if (ret)
+			return ret;
+
+		*val = val16;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		ret = adis_read_reg_16(adis, ADIS16260_SMPL_PRD, &val16);
+		if (ret)
+			return ret;
+
+		if (spi_get_device_id(adis->spi)->driver_data)
+		/* If an adis16251 */
+			*val = (val16 & ADIS16260_SMPL_PRD_TIME_BASE) ?
+				8 : 256;
+		else
+			*val = (val16 & ADIS16260_SMPL_PRD_TIME_BASE) ?
+				66 : 2048;
+		*val /= (val16 & ADIS16260_SMPL_PRD_DIV_MASK) + 1;
+		return IIO_VAL_INT;
+	}
+	return -EINVAL;
+}
+
+static int adis16260_write_raw(struct iio_dev *indio_dev,
+			       struct iio_chan_spec const *chan,
+			       int val,
+			       int val2,
+			       long mask)
+{
+	struct adis16260 *adis16260 = iio_priv(indio_dev);
+	struct adis *adis = &adis16260->adis;
+	int ret;
+	u8 addr;
+	u8 t;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_CALIBBIAS:
+		if (val < -2048 || val >= 2048)
+			return -EINVAL;
+
+		addr = adis16260_addresses[chan->scan_index][0];
+		return adis_write_reg_16(adis, addr, val);
+	case IIO_CHAN_INFO_CALIBSCALE:
+		if (val < 0 || val >= 4096)
+			return -EINVAL;
+
+		addr = adis16260_addresses[chan->scan_index][1];
+		return adis_write_reg_16(adis, addr, val);
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		mutex_lock(&indio_dev->mlock);
+		if (spi_get_device_id(adis->spi)->driver_data)
+			t = 256 / val;
+		else
+			t = 2048 / val;
+
+		if (t > ADIS16260_SMPL_PRD_DIV_MASK)
+			t = ADIS16260_SMPL_PRD_DIV_MASK;
+		else if (t > 0)
+			t--;
+
+		if (t >= 0x0A)
+			adis->spi->max_speed_hz = ADIS16260_SPI_SLOW;
+		else
+			adis->spi->max_speed_hz = ADIS16260_SPI_FAST;
+		ret = adis_write_reg_8(adis, ADIS16260_SMPL_PRD, t);
+
+		mutex_unlock(&indio_dev->mlock);
+		return ret;
+	}
+	return -EINVAL;
+}
+
+static const struct iio_info adis16260_info = {
+	.read_raw = &adis16260_read_raw,
+	.write_raw = &adis16260_write_raw,
+	.update_scan_mode = adis_update_scan_mode,
+	.driver_module = THIS_MODULE,
+};
+
+static const char * const adis1620_status_error_msgs[] = {
+	[ADIS16260_DIAG_STAT_FLASH_CHK_BIT] = "Flash checksum error",
+	[ADIS16260_DIAG_STAT_SELF_TEST_BIT] = "Self test error",
+	[ADIS16260_DIAG_STAT_OVERFLOW_BIT] = "Sensor overrange",
+	[ADIS16260_DIAG_STAT_SPI_FAIL_BIT] = "SPI failure",
+	[ADIS16260_DIAG_STAT_FLASH_UPT_BIT] = "Flash update failed",
+	[ADIS16260_DIAG_STAT_POWER_HIGH_BIT] = "Power supply above 5.25",
+	[ADIS16260_DIAG_STAT_POWER_LOW_BIT] = "Power supply below 4.75",
+};
+
+static const struct adis_data adis16260_data = {
+	.write_delay = 30,
+	.read_delay = 30,
+	.msc_ctrl_reg = ADIS16260_MSC_CTRL,
+	.glob_cmd_reg = ADIS16260_GLOB_CMD,
+	.diag_stat_reg = ADIS16260_DIAG_STAT,
+
+	.self_test_mask = ADIS16260_MSC_CTRL_MEM_TEST,
+	.startup_delay = ADIS16260_STARTUP_DELAY,
+
+	.status_error_msgs = adis1620_status_error_msgs,
+	.status_error_mask = BIT(ADIS16260_DIAG_STAT_FLASH_CHK_BIT) |
+		BIT(ADIS16260_DIAG_STAT_SELF_TEST_BIT) |
+		BIT(ADIS16260_DIAG_STAT_OVERFLOW_BIT) |
+		BIT(ADIS16260_DIAG_STAT_SPI_FAIL_BIT) |
+		BIT(ADIS16260_DIAG_STAT_FLASH_UPT_BIT) |
+		BIT(ADIS16260_DIAG_STAT_POWER_HIGH_BIT) |
+		BIT(ADIS16260_DIAG_STAT_POWER_LOW_BIT),
+};
+
+static int adis16260_probe(struct spi_device *spi)
+{
+	const struct spi_device_id *id;
+	struct adis16260 *adis16260;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	id = spi_get_device_id(spi);
+	if (!id)
+		return -ENODEV;
+
+	/* setup the industrialio driver allocated elements */
+	indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*adis16260));
+	if (!indio_dev)
+		return -ENOMEM;
+	adis16260 = iio_priv(indio_dev);
+	/* this is only used for removal purposes */
+	spi_set_drvdata(spi, indio_dev);
+
+	adis16260->info = &adis16260_chip_info_table[id->driver_data];
+
+	indio_dev->name = id->name;
+	indio_dev->dev.parent = &spi->dev;
+	indio_dev->info = &adis16260_info;
+	indio_dev->channels = adis16260->info->channels;
+	indio_dev->num_channels = adis16260->info->num_channels;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	ret = adis_init(&adis16260->adis, indio_dev, spi, &adis16260_data);
+	if (ret)
+		return ret;
+
+	ret = adis_setup_buffer_and_trigger(&adis16260->adis, indio_dev, NULL);
+	if (ret)
+		return ret;
+
+	/* Get the device into a sane initial state */
+	ret = adis_initial_startup(&adis16260->adis);
+	if (ret)
+		goto error_cleanup_buffer_trigger;
+	ret = iio_device_register(indio_dev);
+	if (ret)
+		goto error_cleanup_buffer_trigger;
+
+	return 0;
+
+error_cleanup_buffer_trigger:
+	adis_cleanup_buffer_and_trigger(&adis16260->adis, indio_dev);
+	return ret;
+}
+
+static int adis16260_remove(struct spi_device *spi)
+{
+	struct iio_dev *indio_dev = spi_get_drvdata(spi);
+	struct adis16260 *adis16260 = iio_priv(indio_dev);
+
+	iio_device_unregister(indio_dev);
+	adis16260_stop_device(indio_dev);
+	adis_cleanup_buffer_and_trigger(&adis16260->adis, indio_dev);
+
+	return 0;
+}
+
+/*
+ * These parts do not need to be differentiated until someone adds
+ * support for the on chip filtering.
+ */
+static const struct spi_device_id adis16260_id[] = {
+	{"adis16260", ADIS16260},
+	{"adis16265", ADIS16260},
+	{"adis16266", ADIS16266},
+	{"adis16250", ADIS16260},
+	{"adis16255", ADIS16260},
+	{"adis16251", ADIS16251},
+	{}
+};
+MODULE_DEVICE_TABLE(spi, adis16260_id);
+
+static struct spi_driver adis16260_driver = {
+	.driver = {
+		.name = "adis16260",
+	},
+	.probe = adis16260_probe,
+	.remove = adis16260_remove,
+	.id_table = adis16260_id,
+};
+module_spi_driver(adis16260_driver);
+
+MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>");
+MODULE_DESCRIPTION("Analog Devices ADIS16260/5 Digital Gyroscope Sensor");
+MODULE_LICENSE("GPL v2");