diff --git a/include/linux/i2c/adp5588.h b/include/linux/i2c/adp5588.h
new file mode 100644
index 0000000..c215304
--- /dev/null
+++ b/include/linux/i2c/adp5588.h
@@ -0,0 +1,172 @@
+/*
+ * Analog Devices ADP5588 I/O Expander and QWERTY Keypad Controller
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _ADP5588_H
+#define _ADP5588_H
+
+#define DEV_ID 0x00		/* Device ID */
+#define CFG 0x01		/* Configuration Register1 */
+#define INT_STAT 0x02		/* Interrupt Status Register */
+#define KEY_LCK_EC_STAT 0x03	/* Key Lock and Event Counter Register */
+#define Key_EVENTA 0x04		/* Key Event Register A */
+#define Key_EVENTB 0x05		/* Key Event Register B */
+#define Key_EVENTC 0x06		/* Key Event Register C */
+#define Key_EVENTD 0x07		/* Key Event Register D */
+#define Key_EVENTE 0x08		/* Key Event Register E */
+#define Key_EVENTF 0x09		/* Key Event Register F */
+#define Key_EVENTG 0x0A		/* Key Event Register G */
+#define Key_EVENTH 0x0B		/* Key Event Register H */
+#define Key_EVENTI 0x0C		/* Key Event Register I */
+#define Key_EVENTJ 0x0D		/* Key Event Register J */
+#define KP_LCK_TMR 0x0E		/* Keypad Lock1 to Lock2 Timer */
+#define UNLOCK1 0x0F		/* Unlock Key1 */
+#define UNLOCK2 0x10		/* Unlock Key2 */
+#define GPIO_INT_STAT1 0x11	/* GPIO Interrupt Status */
+#define GPIO_INT_STAT2 0x12	/* GPIO Interrupt Status */
+#define GPIO_INT_STAT3 0x13	/* GPIO Interrupt Status */
+#define GPIO_DAT_STAT1 0x14	/* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT2 0x15	/* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT3 0x16	/* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_OUT1 0x17	/* GPIO DATA OUT */
+#define GPIO_DAT_OUT2 0x18	/* GPIO DATA OUT */
+#define GPIO_DAT_OUT3 0x19	/* GPIO DATA OUT */
+#define GPIO_INT_EN1 0x1A	/* GPIO Interrupt Enable */
+#define GPIO_INT_EN2 0x1B	/* GPIO Interrupt Enable */
+#define GPIO_INT_EN3 0x1C	/* GPIO Interrupt Enable */
+#define KP_GPIO1 0x1D		/* Keypad or GPIO Selection */
+#define KP_GPIO2 0x1E		/* Keypad or GPIO Selection */
+#define KP_GPIO3 0x1F		/* Keypad or GPIO Selection */
+#define GPI_EM1 0x20		/* GPI Event Mode 1 */
+#define GPI_EM2 0x21		/* GPI Event Mode 2 */
+#define GPI_EM3 0x22		/* GPI Event Mode 3 */
+#define GPIO_DIR1 0x23		/* GPIO Data Direction */
+#define GPIO_DIR2 0x24		/* GPIO Data Direction */
+#define GPIO_DIR3 0x25		/* GPIO Data Direction */
+#define GPIO_INT_LVL1 0x26	/* GPIO Edge/Level Detect */
+#define GPIO_INT_LVL2 0x27	/* GPIO Edge/Level Detect */
+#define GPIO_INT_LVL3 0x28	/* GPIO Edge/Level Detect */
+#define Debounce_DIS1 0x29	/* Debounce Disable */
+#define Debounce_DIS2 0x2A	/* Debounce Disable */
+#define Debounce_DIS3 0x2B	/* Debounce Disable */
+#define GPIO_PULL1 0x2C		/* GPIO Pull Disable */
+#define GPIO_PULL2 0x2D		/* GPIO Pull Disable */
+#define GPIO_PULL3 0x2E		/* GPIO Pull Disable */
+#define CMP_CFG_STAT 0x30	/* Comparator Configuration and Status Register */
+#define CMP_CONFG_SENS1 0x31	/* Sensor1 Comparator Configuration Register */
+#define CMP_CONFG_SENS2 0x32	/* L2 Light Sensor Reference Level, Output Falling for Sensor 1 */
+#define CMP1_LVL2_TRIP 0x33	/* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 1 */
+#define CMP1_LVL2_HYS 0x34	/* L3 Light Sensor Reference Level, Output Falling For Sensor 1 */
+#define CMP1_LVL3_TRIP 0x35	/* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 1 */
+#define CMP1_LVL3_HYS 0x36	/* Sensor 2 Comparator Configuration Register */
+#define CMP2_LVL2_TRIP 0x37	/* L2 Light Sensor Reference Level, Output Falling for Sensor 2 */
+#define CMP2_LVL2_HYS 0x38	/* L2 Light Sensor Hysteresis (Active when Output Rising) for Sensor 2 */
+#define CMP2_LVL3_TRIP 0x39	/* L3 Light Sensor Reference Level, Output Falling For Sensor 2 */
+#define CMP2_LVL3_HYS 0x3A	/* L3 Light Sensor Hysteresis (Active when Output Rising) For Sensor 2 */
+#define CMP1_ADC_DAT_R1 0x3B	/* Comparator 1 ADC data Register1 */
+#define CMP1_ADC_DAT_R2 0x3C	/* Comparator 1 ADC data Register2 */
+#define CMP2_ADC_DAT_R1 0x3D	/* Comparator 2 ADC data Register1 */
+#define CMP2_ADC_DAT_R2 0x3E	/* Comparator 2 ADC data Register2 */
+
+#define ADP5588_DEVICE_ID_MASK	0xF
+
+ /* Configuration Register1 */
+#define ADP5588_AUTO_INC	(1 << 7)
+#define ADP5588_GPIEM_CFG	(1 << 6)
+#define ADP5588_OVR_FLOW_M	(1 << 5)
+#define ADP5588_INT_CFG		(1 << 4)
+#define ADP5588_OVR_FLOW_IEN	(1 << 3)
+#define ADP5588_K_LCK_IM	(1 << 2)
+#define ADP5588_GPI_IEN		(1 << 1)
+#define ADP5588_KE_IEN		(1 << 0)
+
+/* Interrupt Status Register */
+#define ADP5588_CMP2_INT	(1 << 5)
+#define ADP5588_CMP1_INT	(1 << 4)
+#define ADP5588_OVR_FLOW_INT	(1 << 3)
+#define ADP5588_K_LCK_INT	(1 << 2)
+#define ADP5588_GPI_INT		(1 << 1)
+#define ADP5588_KE_INT		(1 << 0)
+
+/* Key Lock and Event Counter Register */
+#define ADP5588_K_LCK_EN	(1 << 6)
+#define ADP5588_LCK21		0x30
+#define ADP5588_KEC		0xF
+
+#define ADP5588_MAXGPIO		18
+#define ADP5588_BANK(offs)	((offs) >> 3)
+#define ADP5588_BIT(offs)	(1u << ((offs) & 0x7))
+
+/* Put one of these structures in i2c_board_info platform_data */
+
+#define ADP5588_KEYMAPSIZE	80
+
+#define GPI_PIN_ROW0 97
+#define GPI_PIN_ROW1 98
+#define GPI_PIN_ROW2 99
+#define GPI_PIN_ROW3 100
+#define GPI_PIN_ROW4 101
+#define GPI_PIN_ROW5 102
+#define GPI_PIN_ROW6 103
+#define GPI_PIN_ROW7 104
+#define GPI_PIN_COL0 105
+#define GPI_PIN_COL1 106
+#define GPI_PIN_COL2 107
+#define GPI_PIN_COL3 108
+#define GPI_PIN_COL4 109
+#define GPI_PIN_COL5 110
+#define GPI_PIN_COL6 111
+#define GPI_PIN_COL7 112
+#define GPI_PIN_COL8 113
+#define GPI_PIN_COL9 114
+
+#define GPI_PIN_ROW_BASE GPI_PIN_ROW0
+#define GPI_PIN_ROW_END GPI_PIN_ROW7
+#define GPI_PIN_COL_BASE GPI_PIN_COL0
+#define GPI_PIN_COL_END GPI_PIN_COL9
+
+#define GPI_PIN_BASE GPI_PIN_ROW_BASE
+#define GPI_PIN_END GPI_PIN_COL_END
+
+#define ADP5588_GPIMAPSIZE_MAX (GPI_PIN_END - GPI_PIN_BASE + 1)
+
+struct adp5588_gpi_map {
+	unsigned short pin;
+	unsigned short sw_evt;
+};
+
+struct adp5588_kpad_platform_data {
+	int rows;			/* Number of rows */
+	int cols;			/* Number of columns */
+	const unsigned short *keymap;	/* Pointer to keymap */
+	unsigned short keymapsize;	/* Keymap size */
+	unsigned repeat:1;		/* Enable key repeat */
+	unsigned en_keylock:1;		/* Enable Key Lock feature */
+	unsigned short unlock_key1;	/* Unlock Key 1 */
+	unsigned short unlock_key2;	/* Unlock Key 2 */
+	const struct adp5588_gpi_map *gpimap;
+	unsigned short gpimapsize;
+	const struct adp5588_gpio_platform_data *gpio_data;
+};
+
+struct i2c_client; /* forward declaration */
+
+struct adp5588_gpio_platform_data {
+	int gpio_start;		/* GPIO Chip base # */
+	const char *const *names;
+	unsigned irq_base;	/* interrupt base # */
+	unsigned pullup_dis_mask; /* Pull-Up Disable Mask */
+	int	(*setup)(struct i2c_client *client,
+				unsigned gpio, unsigned ngpio,
+				void *context);
+	int	(*teardown)(struct i2c_client *client,
+				unsigned gpio, unsigned ngpio,
+				void *context);
+	void	*context;
+};
+
+#endif
diff --git a/include/linux/i2c/adp8860.h b/include/linux/i2c/adp8860.h
new file mode 100644
index 0000000..0b4d398
--- /dev/null
+++ b/include/linux/i2c/adp8860.h
@@ -0,0 +1,154 @@
+/*
+ * Definitions and platform data for Analog Devices
+ * Backlight drivers ADP8860
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __LINUX_I2C_ADP8860_H
+#define __LINUX_I2C_ADP8860_H
+
+#include <linux/leds.h>
+#include <linux/types.h>
+
+#define ID_ADP8860		8860
+
+#define ADP8860_MAX_BRIGHTNESS	0x7F
+#define FLAG_OFFT_SHIFT 8
+
+/*
+ * LEDs subdevice platform data
+ */
+
+#define ADP8860_LED_DIS_BLINK	(0 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_600ms	(1 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_1200ms	(2 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_1800ms	(3 << FLAG_OFFT_SHIFT)
+
+#define ADP8860_LED_ONT_200ms	0
+#define ADP8860_LED_ONT_600ms	1
+#define ADP8860_LED_ONT_800ms	2
+#define ADP8860_LED_ONT_1200ms	3
+
+#define ADP8860_LED_D7		(7)
+#define ADP8860_LED_D6		(6)
+#define ADP8860_LED_D5		(5)
+#define ADP8860_LED_D4		(4)
+#define ADP8860_LED_D3		(3)
+#define ADP8860_LED_D2		(2)
+#define ADP8860_LED_D1		(1)
+
+/*
+ * Backlight subdevice platform data
+ */
+
+#define ADP8860_BL_D7		(1 << 6)
+#define ADP8860_BL_D6		(1 << 5)
+#define ADP8860_BL_D5		(1 << 4)
+#define ADP8860_BL_D4		(1 << 3)
+#define ADP8860_BL_D3		(1 << 2)
+#define ADP8860_BL_D2		(1 << 1)
+#define ADP8860_BL_D1		(1 << 0)
+
+#define ADP8860_FADE_T_DIS	0	/* Fade Timer Disabled */
+#define ADP8860_FADE_T_300ms	1	/* 0.3 Sec */
+#define ADP8860_FADE_T_600ms	2
+#define ADP8860_FADE_T_900ms	3
+#define ADP8860_FADE_T_1200ms	4
+#define ADP8860_FADE_T_1500ms	5
+#define ADP8860_FADE_T_1800ms	6
+#define ADP8860_FADE_T_2100ms	7
+#define ADP8860_FADE_T_2400ms	8
+#define ADP8860_FADE_T_2700ms	9
+#define ADP8860_FADE_T_3000ms	10
+#define ADP8860_FADE_T_3500ms	11
+#define ADP8860_FADE_T_4000ms	12
+#define ADP8860_FADE_T_4500ms	13
+#define ADP8860_FADE_T_5000ms	14
+#define ADP8860_FADE_T_5500ms	15	/* 5.5 Sec */
+
+#define ADP8860_FADE_LAW_LINEAR	0
+#define ADP8860_FADE_LAW_SQUARE	1
+#define ADP8860_FADE_LAW_CUBIC1	2
+#define ADP8860_FADE_LAW_CUBIC2	3
+
+#define ADP8860_BL_AMBL_FILT_80ms	0	/* Light sensor filter time */
+#define ADP8860_BL_AMBL_FILT_160ms	1
+#define ADP8860_BL_AMBL_FILT_320ms	2
+#define ADP8860_BL_AMBL_FILT_640ms	3
+#define ADP8860_BL_AMBL_FILT_1280ms	4
+#define ADP8860_BL_AMBL_FILT_2560ms	5
+#define ADP8860_BL_AMBL_FILT_5120ms	6
+#define ADP8860_BL_AMBL_FILT_10240ms	7	/* 10.24 sec */
+
+/*
+ * Blacklight current 0..30mA
+ */
+#define ADP8860_BL_CUR_mA(I)		((I * 127) / 30)
+
+/*
+ * L2 comparator current 0..1106uA
+ */
+#define ADP8860_L2_COMP_CURR_uA(I)	((I * 255) / 1106)
+
+/*
+ * L3 comparator current 0..138uA
+ */
+#define ADP8860_L3_COMP_CURR_uA(I)	((I * 255) / 138)
+
+struct adp8860_backlight_platform_data {
+	u8 bl_led_assign;	/* 1 = Backlight 0 = Individual LED */
+
+	u8 bl_fade_in;		/* Backlight Fade-In Timer */
+	u8 bl_fade_out;		/* Backlight Fade-Out Timer */
+	u8 bl_fade_law;		/* fade-on/fade-off transfer characteristic */
+
+	u8 en_ambl_sens;	/* 1 = enable ambient light sensor */
+	u8 abml_filt;		/* Light sensor filter time */
+
+	u8 l1_daylight_max;	/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l1_daylight_dim;	/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l2_office_max;	/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l2_office_dim;	/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l3_dark_max;		/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l3_dark_dim;		/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+
+	u8 l2_trip;		/* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+	u8 l2_hyst;		/* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+	u8 l3_trip;		/* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+	u8 l3_hyst;		/* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+
+	/**
+	 * Independent Current Sinks / LEDS
+	 * Sinks not assigned to the Backlight can be exposed to
+	 * user space using the LEDS CLASS interface
+	 */
+
+	int num_leds;
+	struct led_info	*leds;
+	u8 led_fade_in;		/* LED Fade-In Timer */
+	u8 led_fade_out;	/* LED Fade-Out Timer */
+	u8 led_fade_law;	/* fade-on/fade-off transfer characteristic */
+	u8 led_on_time;
+
+	/**
+	 * Gain down disable. Setting this option does not allow the
+	 * charge pump to switch to lower gains. NOT AVAILABLE on ADP8860
+	 * 1 = the charge pump doesn't switch down in gain until all LEDs are 0.
+	 *  The charge pump switches up in gain as needed. This feature is
+	 *  useful if the ADP8863 charge pump is used to drive an external load.
+	 *  This feature must be used when utilizing small fly capacitors
+	 *  (0402 or smaller).
+	 * 0 = the charge pump automatically switches up and down in gain.
+	 *  This provides optimal efficiency, but is not suitable for driving
+	 *  loads that are not connected through the ADP8863 diode drivers.
+	 *  Additionally, the charge pump fly capacitors should be low ESR
+	 * and sized 0603 or greater.
+	 */
+
+	u8 gdwn_dis;
+};
+
+#endif /* __LINUX_I2C_ADP8860_H */
diff --git a/include/linux/i2c/adp8870.h b/include/linux/i2c/adp8870.h
new file mode 100644
index 0000000..624dcec
--- /dev/null
+++ b/include/linux/i2c/adp8870.h
@@ -0,0 +1,153 @@
+/*
+ * Definitions and platform data for Analog Devices
+ * Backlight drivers ADP8870
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __LINUX_I2C_ADP8870_H
+#define __LINUX_I2C_ADP8870_H
+
+#define ID_ADP8870		8870
+
+#define ADP8870_MAX_BRIGHTNESS	0x7F
+#define FLAG_OFFT_SHIFT 8
+
+/*
+ * LEDs subdevice platform data
+ */
+
+#define ADP8870_LED_DIS_BLINK	(0 << FLAG_OFFT_SHIFT)
+#define ADP8870_LED_OFFT_600ms	(1 << FLAG_OFFT_SHIFT)
+#define ADP8870_LED_OFFT_1200ms	(2 << FLAG_OFFT_SHIFT)
+#define ADP8870_LED_OFFT_1800ms	(3 << FLAG_OFFT_SHIFT)
+
+#define ADP8870_LED_ONT_200ms	0
+#define ADP8870_LED_ONT_600ms	1
+#define ADP8870_LED_ONT_800ms	2
+#define ADP8870_LED_ONT_1200ms	3
+
+#define ADP8870_LED_D7		(7)
+#define ADP8870_LED_D6		(6)
+#define ADP8870_LED_D5		(5)
+#define ADP8870_LED_D4		(4)
+#define ADP8870_LED_D3		(3)
+#define ADP8870_LED_D2		(2)
+#define ADP8870_LED_D1		(1)
+
+/*
+ * Backlight subdevice platform data
+ */
+
+#define ADP8870_BL_D7		(1 << 6)
+#define ADP8870_BL_D6		(1 << 5)
+#define ADP8870_BL_D5		(1 << 4)
+#define ADP8870_BL_D4		(1 << 3)
+#define ADP8870_BL_D3		(1 << 2)
+#define ADP8870_BL_D2		(1 << 1)
+#define ADP8870_BL_D1		(1 << 0)
+
+#define ADP8870_FADE_T_DIS	0	/* Fade Timer Disabled */
+#define ADP8870_FADE_T_300ms	1	/* 0.3 Sec */
+#define ADP8870_FADE_T_600ms	2
+#define ADP8870_FADE_T_900ms	3
+#define ADP8870_FADE_T_1200ms	4
+#define ADP8870_FADE_T_1500ms	5
+#define ADP8870_FADE_T_1800ms	6
+#define ADP8870_FADE_T_2100ms	7
+#define ADP8870_FADE_T_2400ms	8
+#define ADP8870_FADE_T_2700ms	9
+#define ADP8870_FADE_T_3000ms	10
+#define ADP8870_FADE_T_3500ms	11
+#define ADP8870_FADE_T_4000ms	12
+#define ADP8870_FADE_T_4500ms	13
+#define ADP8870_FADE_T_5000ms	14
+#define ADP8870_FADE_T_5500ms	15	/* 5.5 Sec */
+
+#define ADP8870_FADE_LAW_LINEAR	0
+#define ADP8870_FADE_LAW_SQUARE	1
+#define ADP8870_FADE_LAW_CUBIC1	2
+#define ADP8870_FADE_LAW_CUBIC2	3
+
+#define ADP8870_BL_AMBL_FILT_80ms	0	/* Light sensor filter time */
+#define ADP8870_BL_AMBL_FILT_160ms	1
+#define ADP8870_BL_AMBL_FILT_320ms	2
+#define ADP8870_BL_AMBL_FILT_640ms	3
+#define ADP8870_BL_AMBL_FILT_1280ms	4
+#define ADP8870_BL_AMBL_FILT_2560ms	5
+#define ADP8870_BL_AMBL_FILT_5120ms	6
+#define ADP8870_BL_AMBL_FILT_10240ms	7	/* 10.24 sec */
+
+/*
+ * Blacklight current 0..30mA
+ */
+#define ADP8870_BL_CUR_mA(I)		((I * 127) / 30)
+
+/*
+ * L2 comparator current 0..1106uA
+ */
+#define ADP8870_L2_COMP_CURR_uA(I)	((I * 255) / 1106)
+
+/*
+ * L3 comparator current 0..551uA
+ */
+#define ADP8870_L3_COMP_CURR_uA(I)	((I * 255) / 551)
+
+/*
+ * L4 comparator current 0..275uA
+ */
+#define ADP8870_L4_COMP_CURR_uA(I)	((I * 255) / 275)
+
+/*
+ * L5 comparator current 0..138uA
+ */
+#define ADP8870_L5_COMP_CURR_uA(I)	((I * 255) / 138)
+
+struct adp8870_backlight_platform_data {
+	u8 bl_led_assign;	/* 1 = Backlight 0 = Individual LED */
+	u8 pwm_assign;		/* 1 = Enables PWM mode */
+
+	u8 bl_fade_in;		/* Backlight Fade-In Timer */
+	u8 bl_fade_out;		/* Backlight Fade-Out Timer */
+	u8 bl_fade_law;		/* fade-on/fade-off transfer characteristic */
+
+	u8 en_ambl_sens;	/* 1 = enable ambient light sensor */
+	u8 abml_filt;		/* Light sensor filter time */
+
+	u8 l1_daylight_max;	/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l1_daylight_dim;	/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l2_bright_max;	/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l2_bright_dim;	/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l3_office_max;	/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l3_office_dim;	/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l4_indoor_max;	/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l4_indor_dim;	/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l5_dark_max;		/* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+	u8 l5_dark_dim;		/* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+
+	u8 l2_trip;		/* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+	u8 l2_hyst;		/* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+	u8 l3_trip;		/* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+	u8 l3_hyst;		/* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+	u8 l4_trip;		/* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
+	u8 l4_hyst;		/* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
+	u8 l5_trip;		/* use L5_COMP_CURR_uA(I) 0 <= I <= 138 uA */
+	u8 l5_hyst;		/* use L6_COMP_CURR_uA(I) 0 <= I <= 138 uA */
+
+	/**
+	 * Independent Current Sinks / LEDS
+	 * Sinks not assigned to the Backlight can be exposed to
+	 * user space using the LEDS CLASS interface
+	 */
+
+	int num_leds;
+	struct led_info	*leds;
+	u8 led_fade_in;		/* LED Fade-In Timer */
+	u8 led_fade_out;	/* LED Fade-Out Timer */
+	u8 led_fade_law;	/* fade-on/fade-off transfer characteristic */
+	u8 led_on_time;
+};
+
+#endif /* __LINUX_I2C_ADP8870_H */
diff --git a/include/linux/i2c/ads1015.h b/include/linux/i2c/ads1015.h
new file mode 100644
index 0000000..d5aa2a0
--- /dev/null
+++ b/include/linux/i2c/ads1015.h
@@ -0,0 +1,36 @@
+/*
+ * Platform Data for ADS1015 12-bit 4-input ADC
+ * (C) Copyright 2010
+ * Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef LINUX_ADS1015_H
+#define LINUX_ADS1015_H
+
+#define ADS1015_CHANNELS 8
+
+struct ads1015_channel_data {
+	bool enabled;
+	unsigned int pga;
+	unsigned int data_rate;
+};
+
+struct ads1015_platform_data {
+	struct ads1015_channel_data channel_data[ADS1015_CHANNELS];
+};
+
+#endif /* LINUX_ADS1015_H */
diff --git a/include/linux/i2c/apds990x.h b/include/linux/i2c/apds990x.h
new file mode 100644
index 0000000..d186fcc
--- /dev/null
+++ b/include/linux/i2c/apds990x.h
@@ -0,0 +1,79 @@
+/*
+ * This file is part of the APDS990x sensor driver.
+ * Chip is combined proximity and ambient light sensor.
+ *
+ * Copyright (C) 2010 Nokia Corporation and/or its subsidiary(-ies).
+ *
+ * Contact: Samu Onkalo <samu.p.onkalo@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __APDS990X_H__
+#define __APDS990X_H__
+
+
+#define APDS_IRLED_CURR_12mA	0x3
+#define APDS_IRLED_CURR_25mA	0x2
+#define APDS_IRLED_CURR_50mA	0x1
+#define APDS_IRLED_CURR_100mA	0x0
+
+/**
+ * struct apds990x_chip_factors - defines effect of the cover window
+ * @ga: Total glass attenuation
+ * @cf1: clear channel factor 1 for raw to lux conversion
+ * @irf1: IR channel factor 1 for raw to lux conversion
+ * @cf2: clear channel factor 2 for raw to lux conversion
+ * @irf2: IR channel factor 2 for raw to lux conversion
+ * @df: device factor for conversion formulas
+ *
+ * Structure for tuning ALS calculation to match with environment.
+ * Values depend on the material above the sensor and the sensor
+ * itself. If the GA is zero, driver will use uncovered sensor default values
+ * format: decimal value * APDS_PARAM_SCALE except df which is plain integer.
+ */
+#define APDS_PARAM_SCALE 4096
+struct apds990x_chip_factors {
+	int ga;
+	int cf1;
+	int irf1;
+	int cf2;
+	int irf2;
+	int df;
+};
+
+/**
+ * struct apds990x_platform_data - platform data for apsd990x.c driver
+ * @cf: chip factor data
+ * @pddrive: IR-led driving current
+ * @ppcount: number of IR pulses used for proximity estimation
+ * @setup_resources: interrupt line setup call back function
+ * @release_resources: interrupt line release call back function
+ *
+ * Proximity detection result depends heavily on correct ppcount, pdrive
+ * and cover window.
+ *
+ */
+
+struct apds990x_platform_data {
+	struct apds990x_chip_factors cf;
+	u8     pdrive;
+	u8     ppcount;
+	int    (*setup_resources)(void);
+	int    (*release_resources)(void);
+};
+
+#endif
diff --git a/include/linux/i2c/bfin_twi.h b/include/linux/i2c/bfin_twi.h
new file mode 100644
index 0000000..135a4e0
--- /dev/null
+++ b/include/linux/i2c/bfin_twi.h
@@ -0,0 +1,145 @@
+/*
+ * i2c-bfin-twi.h - interface to ADI TWI controller
+ *
+ * Copyright 2005-2014 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __I2C_BFIN_TWI_H__
+#define __I2C_BFIN_TWI_H__
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/*
+ * ADI twi registers layout
+ */
+struct bfin_twi_regs {
+	u16 clkdiv;
+	u16 dummy1;
+	u16 control;
+	u16 dummy2;
+	u16 slave_ctl;
+	u16 dummy3;
+	u16 slave_stat;
+	u16 dummy4;
+	u16 slave_addr;
+	u16 dummy5;
+	u16 master_ctl;
+	u16 dummy6;
+	u16 master_stat;
+	u16 dummy7;
+	u16 master_addr;
+	u16 dummy8;
+	u16 int_stat;
+	u16 dummy9;
+	u16 int_mask;
+	u16 dummy10;
+	u16 fifo_ctl;
+	u16 dummy11;
+	u16 fifo_stat;
+	u16 dummy12;
+	u32 __pad[20];
+	u16 xmt_data8;
+	u16 dummy13;
+	u16 xmt_data16;
+	u16 dummy14;
+	u16 rcv_data8;
+	u16 dummy15;
+	u16 rcv_data16;
+	u16 dummy16;
+};
+
+struct bfin_twi_iface {
+	int			irq;
+	spinlock_t		lock;
+	char			read_write;
+	u8			command;
+	u8			*transPtr;
+	int			readNum;
+	int			writeNum;
+	int			cur_mode;
+	int			manual_stop;
+	int			result;
+	struct i2c_adapter	adap;
+	struct completion	complete;
+	struct i2c_msg		*pmsg;
+	int			msg_num;
+	int			cur_msg;
+	u16			saved_clkdiv;
+	u16			saved_control;
+	struct bfin_twi_regs __iomem *regs_base;
+};
+
+/*  ********************  TWO-WIRE INTERFACE (TWI) MASKS  ********************/
+/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y);  ) */
+#define	CLKLOW(x)	((x) & 0xFF)	/* Periods Clock Is Held Low */
+#define CLKHI(y)	(((y)&0xFF)<<0x8) /* Periods Before New Clock Low */
+
+/* TWI_PRESCALE Masks */
+#define	PRESCALE	0x007F	/* SCLKs Per Internal Time Reference (10MHz) */
+#define	TWI_ENA		0x0080	/* TWI Enable */
+#define	SCCB		0x0200	/* SCCB Compatibility Enable */
+
+/* TWI_SLAVE_CTL Masks */
+#define	SEN		0x0001	/* Slave Enable */
+#define	SADD_LEN	0x0002	/* Slave Address Length */
+#define	STDVAL		0x0004	/* Slave Transmit Data Valid */
+#define	NAK		0x0008	/* NAK Generated At Conclusion Of Transfer */
+#define	GEN		0x0010	/* General Call Address Matching Enabled */
+
+/* TWI_SLAVE_STAT Masks	*/
+#define	SDIR		0x0001	/* Slave Transfer Direction (RX/TX*) */
+#define GCALL		0x0002	/* General Call Indicator */
+
+/* TWI_MASTER_CTL Masks	*/
+#define	MEN		0x0001	/* Master Mode Enable          */
+#define	MADD_LEN	0x0002	/* Master Address Length       */
+#define	MDIR		0x0004	/* Master Transmit Direction (RX/TX*) */
+#define	FAST		0x0008	/* Use Fast Mode Timing Specs  */
+#define	STOP		0x0010	/* Issue Stop Condition        */
+#define	RSTART		0x0020	/* Repeat Start or Stop* At End Of Transfer */
+#define	DCNT		0x3FC0	/* Data Bytes To Transfer      */
+#define	SDAOVR		0x4000	/* Serial Data Override        */
+#define	SCLOVR		0x8000	/* Serial Clock Override       */
+
+/* TWI_MASTER_STAT Masks */
+#define	MPROG		0x0001	/* Master Transfer In Progress */
+#define	LOSTARB		0x0002	/* Lost Arbitration Indicator (Xfer Aborted) */
+#define	ANAK		0x0004	/* Address Not Acknowledged    */
+#define	DNAK		0x0008	/* Data Not Acknowledged       */
+#define	BUFRDERR	0x0010	/* Buffer Read Error           */
+#define	BUFWRERR	0x0020	/* Buffer Write Error          */
+#define	SDASEN		0x0040	/* Serial Data Sense           */
+#define	SCLSEN		0x0080	/* Serial Clock Sense          */
+#define	BUSBUSY		0x0100	/* Bus Busy Indicator          */
+
+/* TWI_INT_SRC and TWI_INT_ENABLE Masks	*/
+#define	SINIT		0x0001	/* Slave Transfer Initiated    */
+#define	SCOMP		0x0002	/* Slave Transfer Complete     */
+#define	SERR		0x0004	/* Slave Transfer Error        */
+#define	SOVF		0x0008	/* Slave Overflow              */
+#define	MCOMP		0x0010	/* Master Transfer Complete    */
+#define	MERR		0x0020	/* Master Transfer Error       */
+#define	XMTSERV		0x0040	/* Transmit FIFO Service       */
+#define	RCVSERV		0x0080	/* Receive FIFO Service        */
+
+/* TWI_FIFO_CTRL Masks */
+#define	XMTFLUSH	0x0001	/* Transmit Buffer Flush                 */
+#define	RCVFLUSH	0x0002	/* Receive Buffer Flush                  */
+#define	XMTINTLEN	0x0004	/* Transmit Buffer Interrupt Length      */
+#define	RCVINTLEN	0x0008	/* Receive Buffer Interrupt Length       */
+
+/* TWI_FIFO_STAT Masks */
+#define	XMTSTAT		0x0003	/* Transmit FIFO Status                  */
+#define	XMT_EMPTY	0x0000	/* Transmit FIFO Empty                   */
+#define	XMT_HALF	0x0001	/* Transmit FIFO Has 1 Byte To Write     */
+#define	XMT_FULL	0x0003	/* Transmit FIFO Full (2 Bytes To Write) */
+
+#define	RCVSTAT		0x000C	/* Receive FIFO Status                   */
+#define	RCV_EMPTY	0x0000	/* Receive FIFO Empty                    */
+#define	RCV_HALF	0x0004	/* Receive FIFO Has 1 Byte To Read       */
+#define	RCV_FULL	0x000C	/* Receive FIFO Full (2 Bytes To Read)   */
+
+#endif
diff --git a/include/linux/i2c/bh1770glc.h b/include/linux/i2c/bh1770glc.h
new file mode 100644
index 0000000..8b5e2df
--- /dev/null
+++ b/include/linux/i2c/bh1770glc.h
@@ -0,0 +1,53 @@
+/*
+ * This file is part of the ROHM BH1770GLC / OSRAM SFH7770 sensor driver.
+ * Chip is combined proximity and ambient light sensor.
+ *
+ * Copyright (C) 2010 Nokia Corporation and/or its subsidiary(-ies).
+ *
+ * Contact: Samu Onkalo <samu.p.onkalo@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __BH1770_H__
+#define __BH1770_H__
+
+/**
+ * struct bh1770_platform_data - platform data for bh1770glc driver
+ * @led_def_curr: IR led driving current.
+ * @glass_attenuation: Attenuation factor for covering window.
+ * @setup_resources: Call back for interrupt line setup function
+ * @release_resources: Call back for interrupte line release function
+ *
+ * Example of glass attenuation: 16384 * 385 / 100 means attenuation factor
+ * of 3.85. i.e. light_above_sensor = light_above_cover_window / 3.85
+ */
+
+struct bh1770_platform_data {
+#define BH1770_LED_5mA	0
+#define BH1770_LED_10mA	1
+#define BH1770_LED_20mA	2
+#define BH1770_LED_50mA	3
+#define BH1770_LED_100mA 4
+#define BH1770_LED_150mA 5
+#define BH1770_LED_200mA 6
+	__u8 led_def_curr;
+#define BH1770_NEUTRAL_GA 16384 /* 16384 / 16384 = 1 */
+	__u32 glass_attenuation;
+	int (*setup_resources)(void);
+	int (*release_resources)(void);
+};
+#endif
diff --git a/include/linux/i2c/dm355evm_msp.h b/include/linux/i2c/dm355evm_msp.h
new file mode 100644
index 0000000..3724703
--- /dev/null
+++ b/include/linux/i2c/dm355evm_msp.h
@@ -0,0 +1,79 @@
+/*
+ * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board
+ */
+#ifndef __LINUX_I2C_DM355EVM_MSP
+#define __LINUX_I2C_DM355EVM_MSP
+
+/*
+ * Written against Spectrum's writeup for the A4 firmware revision,
+ * and tweaked to match source and rev D2 schematics by removing CPLD
+ * and NOR flash hooks (which were last appropriate in rev B boards).
+ *
+ * Note that the firmware supports a flavor of write posting ... to be
+ * sure a write completes, issue another read or write.
+ */
+
+/* utilities to access "registers" emulated by msp430 firmware */
+extern int dm355evm_msp_write(u8 value, u8 reg);
+extern int dm355evm_msp_read(u8 reg);
+
+
+/* command/control registers */
+#define DM355EVM_MSP_COMMAND		0x00
+#	define MSP_COMMAND_NULL		0
+#	define MSP_COMMAND_RESET_COLD	1
+#	define MSP_COMMAND_RESET_WARM	2
+#	define MSP_COMMAND_RESET_WARM_I	3
+#	define MSP_COMMAND_POWEROFF	4
+#	define MSP_COMMAND_IR_REINIT	5
+#define DM355EVM_MSP_STATUS		0x01
+#	define MSP_STATUS_BAD_OFFSET	BIT(0)
+#	define MSP_STATUS_BAD_COMMAND	BIT(1)
+#	define MSP_STATUS_POWER_ERROR	BIT(2)
+#	define MSP_STATUS_RXBUF_OVERRUN	BIT(3)
+#define DM355EVM_MSP_RESET		0x02	/* 0 bits == in reset */
+#	define MSP_RESET_DC5		BIT(0)
+#	define MSP_RESET_TVP5154	BIT(2)
+#	define MSP_RESET_IMAGER		BIT(3)
+#	define MSP_RESET_ETHERNET	BIT(4)
+#	define MSP_RESET_SYS		BIT(5)
+#	define MSP_RESET_AIC33		BIT(7)
+
+/* GPIO registers ... bit patterns mostly match the source MSP ports */
+#define DM355EVM_MSP_LED		0x03	/* active low (MSP P4) */
+#define DM355EVM_MSP_SWITCH1		0x04	/* (MSP P5, masked) */
+#	define MSP_SWITCH1_SW6_1	BIT(0)
+#	define MSP_SWITCH1_SW6_2	BIT(1)
+#	define MSP_SWITCH1_SW6_3	BIT(2)
+#	define MSP_SWITCH1_SW6_4	BIT(3)
+#	define MSP_SWITCH1_J1		BIT(4)	/* NTSC/PAL */
+#	define MSP_SWITCH1_MSP_INT	BIT(5)	/* active low */
+#define DM355EVM_MSP_SWITCH2		0x05	/* (MSP P6, masked) */
+#	define MSP_SWITCH2_SW10		BIT(3)
+#	define MSP_SWITCH2_SW11		BIT(4)
+#	define MSP_SWITCH2_SW12		BIT(5)
+#	define MSP_SWITCH2_SW13		BIT(6)
+#	define MSP_SWITCH2_SW14		BIT(7)
+#define DM355EVM_MSP_SDMMC		0x06	/* (MSP P2, masked) */
+#	define MSP_SDMMC_0_WP		BIT(1)
+#	define MSP_SDMMC_0_CD		BIT(2)	/* active low */
+#	define MSP_SDMMC_1_WP		BIT(3)
+#	define MSP_SDMMC_1_CD		BIT(4)	/* active low */
+#define DM355EVM_MSP_FIRMREV		0x07	/* not a GPIO (out of order) */
+#define DM355EVM_MSP_VIDEO_IN		0x08	/* (MSP P3, masked) */
+#	define MSP_VIDEO_IMAGER		BIT(7)	/* low == tvp5146 */
+
+/* power supply registers are currently omitted */
+
+/* RTC registers */
+#define DM355EVM_MSP_RTC_0		0x12	/* LSB */
+#define DM355EVM_MSP_RTC_1		0x13
+#define DM355EVM_MSP_RTC_2		0x14
+#define DM355EVM_MSP_RTC_3		0x15	/* MSB */
+
+/* input event queue registers; code == ((HIGH << 8) | LOW) */
+#define DM355EVM_MSP_INPUT_COUNT	0x16	/* decrement by reading LOW */
+#define DM355EVM_MSP_INPUT_HIGH		0x17
+#define DM355EVM_MSP_INPUT_LOW		0x18
+
+#endif /* __LINUX_I2C_DM355EVM_MSP */
diff --git a/include/linux/i2c/ds620.h b/include/linux/i2c/ds620.h
new file mode 100644
index 0000000..736bb87
--- /dev/null
+++ b/include/linux/i2c/ds620.h
@@ -0,0 +1,21 @@
+#ifndef _LINUX_DS620_H
+#define _LINUX_DS620_H
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/* platform data for the DS620 temperature sensor and thermostat */
+
+struct ds620_platform_data {
+	/*
+	 *  Thermostat output pin PO mode:
+	 *  0 = always low (default)
+	 *  1 = PO_LOW
+	 *  2 = PO_HIGH
+	 *
+	 * (see Documentation/hwmon/ds620)
+	 */
+	int pomode;
+};
+
+#endif /* _LINUX_DS620_H */
diff --git a/include/linux/i2c/i2c-hid.h b/include/linux/i2c/i2c-hid.h
new file mode 100644
index 0000000..7aa901d
--- /dev/null
+++ b/include/linux/i2c/i2c-hid.h
@@ -0,0 +1,36 @@
+/*
+ * HID over I2C protocol implementation
+ *
+ * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@gmail.com>
+ * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive for
+ * more details.
+ */
+
+#ifndef __LINUX_I2C_HID_H
+#define __LINUX_I2C_HID_H
+
+#include <linux/types.h>
+
+/**
+ * struct i2chid_platform_data - used by hid over i2c implementation.
+ * @hid_descriptor_address: i2c register where the HID descriptor is stored.
+ *
+ * Note that it is the responsibility of the platform driver (or the acpi 5.0
+ * driver, or the flattened device tree) to setup the irq related to the gpio in
+ * the struct i2c_board_info.
+ * The platform driver should also setup the gpio according to the device:
+ *
+ * A typical example is the following:
+ *	irq = gpio_to_irq(intr_gpio);
+ *	hkdk4412_i2c_devs5[0].irq = irq; // store the irq in i2c_board_info
+ *	gpio_request(intr_gpio, "elan-irq");
+ *	s3c_gpio_setpull(intr_gpio, S3C_GPIO_PULL_UP);
+ */
+struct i2c_hid_platform_data {
+	u16 hid_descriptor_address;
+};
+
+#endif /* __LINUX_I2C_HID_H */
diff --git a/include/linux/i2c/i2c-sh_mobile.h b/include/linux/i2c/i2c-sh_mobile.h
new file mode 100644
index 0000000..06e3089
--- /dev/null
+++ b/include/linux/i2c/i2c-sh_mobile.h
@@ -0,0 +1,11 @@
+#ifndef __I2C_SH_MOBILE_H__
+#define __I2C_SH_MOBILE_H__
+
+#include <linux/platform_device.h>
+
+struct i2c_sh_mobile_platform_data {
+	unsigned long bus_speed;
+	unsigned int clks_per_count;
+};
+
+#endif /* __I2C_SH_MOBILE_H__ */
diff --git a/include/linux/i2c/lm8323.h b/include/linux/i2c/lm8323.h
new file mode 100644
index 0000000..478d668
--- /dev/null
+++ b/include/linux/i2c/lm8323.h
@@ -0,0 +1,46 @@
+/*
+ * lm8323.h - Configuration for LM8323 keypad driver.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation (version 2 of the License only).
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __LINUX_LM8323_H
+#define __LINUX_LM8323_H
+
+#include <linux/types.h>
+
+/*
+ * Largest keycode that the chip can send, plus one,
+ * so keys can be mapped directly at the index of the
+ * LM8323 keycode instead of subtracting one.
+ */
+#define LM8323_KEYMAP_SIZE	(0x7f + 1)
+
+#define LM8323_NUM_PWMS		3
+
+struct lm8323_platform_data {
+	int debounce_time; /* Time to watch for key bouncing, in ms. */
+	int active_time; /* Idle time until sleep, in ms. */
+
+	int size_x;
+	int size_y;
+	bool repeat;
+	const unsigned short *keymap;
+
+	const char *pwm_names[LM8323_NUM_PWMS];
+
+	const char *name; /* Device name. */
+};
+
+#endif /* __LINUX_LM8323_H */
diff --git a/include/linux/i2c/ltc4245.h b/include/linux/i2c/ltc4245.h
new file mode 100644
index 0000000..56bda4b
--- /dev/null
+++ b/include/linux/i2c/ltc4245.h
@@ -0,0 +1,21 @@
+/*
+ * Platform Data for LTC4245 hardware monitor chip
+ *
+ * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef LINUX_LTC4245_H
+#define LINUX_LTC4245_H
+
+#include <linux/types.h>
+
+struct ltc4245_platform_data {
+	bool use_extra_gpios;
+};
+
+#endif /* LINUX_LTC4245_H */
diff --git a/include/linux/i2c/max6639.h b/include/linux/i2c/max6639.h
new file mode 100644
index 0000000..6011c42
--- /dev/null
+++ b/include/linux/i2c/max6639.h
@@ -0,0 +1,14 @@
+#ifndef _LINUX_MAX6639_H
+#define _LINUX_MAX6639_H
+
+#include <linux/types.h>
+
+/* platform data for the MAX6639 temperature sensor and fan control */
+
+struct max6639_platform_data {
+	bool pwm_polarity;	/* Polarity low (0) or high (1, default) */
+	int ppr;		/* Pulses per rotation 1..4 (default == 2) */
+	int rpm_range;		/* 2000, 4000 (default), 8000 or 16000 */
+};
+
+#endif /* _LINUX_MAX6639_H */
diff --git a/include/linux/i2c/max732x.h b/include/linux/i2c/max732x.h
new file mode 100644
index 0000000..c04bac8
--- /dev/null
+++ b/include/linux/i2c/max732x.h
@@ -0,0 +1,22 @@
+#ifndef __LINUX_I2C_MAX732X_H
+#define __LINUX_I2C_MAX732X_H
+
+/* platform data for the MAX732x 8/16-bit I/O expander driver */
+
+struct max732x_platform_data {
+	/* number of the first GPIO */
+	unsigned	gpio_base;
+
+	/* interrupt base */
+	int		irq_base;
+
+	void		*context;	/* param to setup/teardown */
+
+	int		(*setup)(struct i2c_client *client,
+				unsigned gpio, unsigned ngpio,
+				void *context);
+	int		(*teardown)(struct i2c_client *client,
+				unsigned gpio, unsigned ngpio,
+				void *context);
+};
+#endif /* __LINUX_I2C_MAX732X_H */
diff --git a/include/linux/i2c/mcs.h b/include/linux/i2c/mcs.h
new file mode 100644
index 0000000..61bb18a
--- /dev/null
+++ b/include/linux/i2c/mcs.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright (C) 2009 - 2010 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ * Author: HeungJun Kim <riverful.kim@samsung.com>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#ifndef __LINUX_MCS_H
+#define __LINUX_MCS_H
+
+#define MCS_KEY_MAP(v, c)	((((v) & 0xff) << 16) | ((c) & 0xffff))
+#define MCS_KEY_VAL(v)		(((v) >> 16) & 0xff)
+#define MCS_KEY_CODE(v)		((v) & 0xffff)
+
+struct mcs_platform_data {
+	void (*poweron)(bool);
+	void (*cfg_pin)(void);
+
+	/* touchscreen */
+	unsigned int x_size;
+	unsigned int y_size;
+
+	/* touchkey */
+	const u32 *keymap;
+	unsigned int keymap_size;
+	unsigned int key_maxval;
+	bool no_autorepeat;
+};
+
+#endif	/* __LINUX_MCS_H */
diff --git a/include/linux/i2c/mms114.h b/include/linux/i2c/mms114.h
new file mode 100644
index 0000000..5722ebf
--- /dev/null
+++ b/include/linux/i2c/mms114.h
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundationr
+ */
+
+#ifndef __LINUX_MMS114_H
+#define __LINUX_MMS114_H
+
+struct mms114_platform_data {
+	unsigned int x_size;
+	unsigned int y_size;
+	unsigned int contact_threshold;
+	unsigned int moving_threshold;
+	bool x_invert;
+	bool y_invert;
+
+	void (*cfg_pin)(bool);
+};
+
+#endif	/* __LINUX_MMS114_H */
diff --git a/include/linux/i2c/mpr121_touchkey.h b/include/linux/i2c/mpr121_touchkey.h
new file mode 100644
index 0000000..f0bcc38
--- /dev/null
+++ b/include/linux/i2c/mpr121_touchkey.h
@@ -0,0 +1,20 @@
+/* Header file for Freescale MPR121 Capacitive Touch Sensor */
+
+#ifndef _MPR121_TOUCHKEY_H
+#define _MPR121_TOUCHKEY_H
+
+/**
+ * struct mpr121_platform_data - platform data for mpr121 sensor
+ * @keymap: pointer to array of KEY_* values representing keymap
+ * @keymap_size: size of the keymap
+ * @wakeup: configure the button as a wake-up source
+ * @vdd_uv: VDD voltage in uV
+ */
+struct mpr121_platform_data {
+	const unsigned short *keymap;
+	unsigned int keymap_size;
+	bool wakeup;
+	int vdd_uv;
+};
+
+#endif /* _MPR121_TOUCHKEY_H */
diff --git a/include/linux/i2c/pca954x.h b/include/linux/i2c/pca954x.h
new file mode 100644
index 0000000..1712677
--- /dev/null
+++ b/include/linux/i2c/pca954x.h
@@ -0,0 +1,48 @@
+/*
+ *
+ * pca954x.h - I2C multiplexer/switch support
+ *
+ * Copyright (c) 2008-2009 Rodolfo Giometti <giometti@linux.it>
+ * Copyright (c) 2008-2009 Eurotech S.p.A. <info@eurotech.it>
+ * Michael Lawnick <michael.lawnick.ext@nsn.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+
+#ifndef _LINUX_I2C_PCA954X_H
+#define _LINUX_I2C_PCA954X_H
+
+/* Platform data for the PCA954x I2C multiplexers */
+
+/* Per channel initialisation data:
+ * @adap_id: bus number for the adapter. 0 = don't care
+ * @deselect_on_exit: set this entry to 1, if your H/W needs deselection
+ *                    of this channel after transaction.
+ *
+ */
+struct pca954x_platform_mode {
+	int		adap_id;
+	unsigned int	deselect_on_exit:1;
+	unsigned int	class;
+};
+
+/* Per mux/switch data, used with i2c_register_board_info */
+struct pca954x_platform_data {
+	struct pca954x_platform_mode *modes;
+	int num_modes;
+};
+
+#endif /* _LINUX_I2C_PCA954X_H */
diff --git a/include/linux/i2c/pcf857x.h b/include/linux/i2c/pcf857x.h
new file mode 100644
index 0000000..0767a2a
--- /dev/null
+++ b/include/linux/i2c/pcf857x.h
@@ -0,0 +1,44 @@
+#ifndef __LINUX_PCF857X_H
+#define __LINUX_PCF857X_H
+
+/**
+ * struct pcf857x_platform_data - data to set up pcf857x driver
+ * @gpio_base: number of the chip's first GPIO
+ * @n_latch: optional bit-inverse of initial register value; if
+ *	you leave this initialized to zero the driver will act
+ *	like the chip was just reset
+ * @setup: optional callback issued once the GPIOs are valid
+ * @teardown: optional callback issued before the GPIOs are invalidated
+ * @context: optional parameter passed to setup() and teardown()
+ *
+ * In addition to the I2C_BOARD_INFO() state appropriate to each chip,
+ * the i2c_board_info used with the pcf875x driver must provide its
+ * platform_data (pointer to one of these structures) with at least
+ * the gpio_base value initialized.
+ *
+ * The @setup callback may be used with the kind of board-specific glue
+ * which hands the (now-valid) GPIOs to other drivers, or which puts
+ * devices in their initial states using these GPIOs.
+ *
+ * These GPIO chips are only "quasi-bidirectional"; read the chip specs
+ * to understand the behavior.  They don't have separate registers to
+ * record which pins are used for input or output, record which output
+ * values are driven, or provide access to input values.  That must be
+ * inferred by reading the chip's value and knowing the last value written
+ * to it.  If you leave n_latch initialized to zero, that last written
+ * value is presumed to be all ones (as if the chip were just reset).
+ */
+struct pcf857x_platform_data {
+	unsigned	gpio_base;
+	unsigned	n_latch;
+
+	int		(*setup)(struct i2c_client *client,
+					int gpio, unsigned ngpio,
+					void *context);
+	int		(*teardown)(struct i2c_client *client,
+					int gpio, unsigned ngpio,
+					void *context);
+	void		*context;
+};
+
+#endif /* __LINUX_PCF857X_H */
diff --git a/include/linux/i2c/pmbus.h b/include/linux/i2c/pmbus.h
new file mode 100644
index 0000000..ee3c2ab
--- /dev/null
+++ b/include/linux/i2c/pmbus.h
@@ -0,0 +1,49 @@
+/*
+ * Hardware monitoring driver for PMBus devices
+ *
+ * Copyright (c) 2010, 2011 Ericsson AB.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef _PMBUS_H_
+#define _PMBUS_H_
+
+/* flags */
+
+/*
+ * PMBUS_SKIP_STATUS_CHECK
+ *
+ * During register detection, skip checking the status register for
+ * communication or command errors.
+ *
+ * Some PMBus chips respond with valid data when trying to read an unsupported
+ * register. For such chips, checking the status register is mandatory when
+ * trying to determine if a chip register exists or not.
+ * Other PMBus chips don't support the STATUS_CML register, or report
+ * communication errors for no explicable reason. For such chips, checking
+ * the status register must be disabled.
+ */
+#define PMBUS_SKIP_STATUS_CHECK	(1 << 0)
+
+struct pmbus_platform_data {
+	u32 flags;		/* Device specific flags */
+
+	/* regulator support */
+	int num_regulators;
+	struct regulator_init_data *reg_init_data;
+};
+
+#endif /* _PMBUS_H_ */
diff --git a/include/linux/i2c/pxa-i2c.h b/include/linux/i2c/pxa-i2c.h
new file mode 100644
index 0000000..53aab24
--- /dev/null
+++ b/include/linux/i2c/pxa-i2c.h
@@ -0,0 +1,85 @@
+/*
+ *  i2c_pxa.h
+ *
+ *  Copyright (C) 2002 Intrinsyc Software Inc.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ *
+ */
+#ifndef _I2C_PXA_H_
+#define _I2C_PXA_H_
+
+#if 0
+#define DEF_TIMEOUT             3
+#else
+/* need a longer timeout if we're dealing with the fact we may well be
+ * looking at a multi-master environment
+*/
+#define DEF_TIMEOUT             32
+#endif
+
+#define BUS_ERROR               (-EREMOTEIO)
+#define XFER_NAKED              (-ECONNREFUSED)
+#define I2C_RETRY               (-2000) /* an error has occurred retry transmit */
+
+/* ICR initialize bit values
+*
+*  15. FM       0 (100 Khz operation)
+*  14. UR       0 (No unit reset)
+*  13. SADIE    0 (Disables the unit from interrupting on slave addresses
+*                                       matching its slave address)
+*  12. ALDIE    0 (Disables the unit from interrupt when it loses arbitration
+*                                       in master mode)
+*  11. SSDIE    0 (Disables interrupts from a slave stop detected, in slave mode)
+*  10. BEIE     1 (Enable interrupts from detected bus errors, no ACK sent)
+*  9.  IRFIE    1 (Enable interrupts from full buffer received)
+*  8.  ITEIE    1 (Enables the I2C unit to interrupt when transmit buffer empty)
+*  7.  GCD      1 (Disables i2c unit response to general call messages as a slave)
+*  6.  IUE      0 (Disable unit until we change settings)
+*  5.  SCLE     1 (Enables the i2c clock output for master mode (drives SCL)
+*  4.  MA       0 (Only send stop with the ICR stop bit)
+*  3.  TB       0 (We are not transmitting a byte initially)
+*  2.  ACKNAK   0 (Send an ACK after the unit receives a byte)
+*  1.  STOP     0 (Do not send a STOP)
+*  0.  START    0 (Do not send a START)
+*
+*/
+#define I2C_ICR_INIT	(ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
+
+/* I2C status register init values
+ *
+ * 10. BED      1 (Clear bus error detected)
+ * 9.  SAD      1 (Clear slave address detected)
+ * 7.  IRF      1 (Clear IDBR Receive Full)
+ * 6.  ITE      1 (Clear IDBR Transmit Empty)
+ * 5.  ALD      1 (Clear Arbitration Loss Detected)
+ * 4.  SSD      1 (Clear Slave Stop Detected)
+ */
+#define I2C_ISR_INIT	0x7FF  /* status register init */
+
+struct i2c_slave_client;
+
+struct i2c_pxa_platform_data {
+	unsigned int		slave_addr;
+	struct i2c_slave_client	*slave;
+	unsigned int		class;
+	unsigned int		use_pio :1;
+	unsigned int		fast_mode :1;
+	unsigned int		high_mode:1;
+	unsigned char		master_code;
+	unsigned long		rate;
+};
+
+extern void pxa_set_i2c_info(struct i2c_pxa_platform_data *info);
+
+#ifdef CONFIG_PXA27x
+extern void pxa27x_set_i2c_power_info(struct i2c_pxa_platform_data *info);
+#endif
+
+#ifdef CONFIG_PXA3xx
+extern void pxa3xx_set_i2c_power_info(struct i2c_pxa_platform_data *info);
+#endif
+
+#endif
diff --git a/include/linux/i2c/sx150x.h b/include/linux/i2c/sx150x.h
new file mode 100644
index 0000000..52baa79
--- /dev/null
+++ b/include/linux/i2c/sx150x.h
@@ -0,0 +1,82 @@
+/*
+ * Driver for the Semtech SX150x I2C GPIO Expanders
+ *
+ * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#ifndef __LINUX_I2C_SX150X_H
+#define __LINUX_I2C_SX150X_H
+
+/**
+ * struct sx150x_platform_data - config data for SX150x driver
+ * @gpio_base: The index number of the first GPIO assigned to this
+ *             GPIO expander.  The expander will create a block of
+ *             consecutively numbered gpios beginning at the given base,
+ *             with the size of the block depending on the model of the
+ *             expander chip.
+ * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
+ *                instead of as an oscillator, increasing the size of the
+ *                GP(I)O pool created by this expander by one.  The
+ *                output-only GPO pin will be added at the end of the block.
+ * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
+ *                 for each IO line in the expander.  Setting the bit at
+ *                 position n will enable the pull-up for the IO at
+ *                 the corresponding offset.  For chips with fewer than
+ *                 16 IO pins, high-end bits are ignored.
+ * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
+ *                 resistor for each IO line in the expander. Setting the
+ *                 bit at position n will enable the pull-down for the IO at
+ *                 the corresponding offset.  For chips with fewer than
+ *                 16 IO pins, high-end bits are ignored.
+ * @io_open_drain_ena: A bit-mask which enables-or disables open-drain
+ *                     operation for each IO line in the expander. Setting the
+ *                     bit at position n enables open-drain operation for
+ *                     the IO at the corresponding offset.  Clearing the bit
+ *                     enables regular push-pull operation for that IO.
+ *                     For chips with fewer than 16 IO pins, high-end bits
+ *                     are ignored.
+ * @io_polarity: A bit-mask which enables polarity inversion for each IO line
+ *               in the expander.  Setting the bit at position n inverts
+ *               the polarity of that IO line, while clearing it results
+ *               in normal polarity. For chips with fewer than 16 IO pins,
+ *               high-end bits are ignored.
+ * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
+ *               is connected, via which it reports interrupt events
+ *               across all GPIO lines.  This must be a real,
+ *               pre-existing IRQ line.
+ *               Setting this value < 0 disables the irq_chip functionality
+ *               of the driver.
+ * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
+ *            IRQ lines will appear.  Similarly to gpio_base, the expander
+ *            will create a block of irqs beginning at this number.
+ *            This value is ignored if irq_summary is < 0.
+ * @reset_during_probe: If set to true, the driver will trigger a full
+ *                      reset of the chip at the beginning of the probe
+ *                      in order to place it in a known state.
+ */
+struct sx150x_platform_data {
+	unsigned gpio_base;
+	bool     oscio_is_gpo;
+	u16      io_pullup_ena;
+	u16      io_pulldn_ena;
+	u16      io_open_drain_ena;
+	u16      io_polarity;
+	int      irq_summary;
+	unsigned irq_base;
+	bool     reset_during_probe;
+};
+
+#endif /* __LINUX_I2C_SX150X_H */
diff --git a/include/linux/i2c/tc35876x.h b/include/linux/i2c/tc35876x.h
new file mode 100644
index 0000000..cd6a51c
--- /dev/null
+++ b/include/linux/i2c/tc35876x.h
@@ -0,0 +1,11 @@
+
+#ifndef _TC35876X_H
+#define _TC35876X_H
+
+struct tc35876x_platform_data {
+	int gpio_bridge_reset;
+	int gpio_panel_bl_en;
+	int gpio_panel_vadd;
+};
+
+#endif /* _TC35876X_H */
diff --git a/include/linux/i2c/tps65010.h b/include/linux/i2c/tps65010.h
new file mode 100644
index 0000000..08aa922
--- /dev/null
+++ b/include/linux/i2c/tps65010.h
@@ -0,0 +1,205 @@
+/* linux/i2c/tps65010.h
+ *
+ * Functions to access TPS65010 power management device.
+ *
+ * Copyright (C) 2004 Dirk Behme <dirk.behme@de.bosch.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the  GNU General Public License along
+ * with this program; if not, write  to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __LINUX_I2C_TPS65010_H
+#define __LINUX_I2C_TPS65010_H
+
+/*
+ * ----------------------------------------------------------------------------
+ * Registers, all 8 bits
+ * ----------------------------------------------------------------------------
+ */
+
+#define	TPS_CHGSTATUS		0x01
+#	define	TPS_CHG_USB		(1 << 7)
+#	define	TPS_CHG_AC		(1 << 6)
+#	define	TPS_CHG_THERM		(1 << 5)
+#	define	TPS_CHG_TERM		(1 << 4)
+#	define	TPS_CHG_TAPER_TMO	(1 << 3)
+#	define	TPS_CHG_CHG_TMO		(1 << 2)
+#	define	TPS_CHG_PRECHG_TMO	(1 << 1)
+#	define	TPS_CHG_TEMP_ERR	(1 << 0)
+#define	TPS_REGSTATUS		0x02
+#	define	TPS_REG_ONOFF		(1 << 7)
+#	define	TPS_REG_COVER		(1 << 6)
+#	define	TPS_REG_UVLO		(1 << 5)
+#	define	TPS_REG_NO_CHG		(1 << 4)	/* tps65013 */
+#	define	TPS_REG_PG_LD02		(1 << 3)
+#	define	TPS_REG_PG_LD01		(1 << 2)
+#	define	TPS_REG_PG_MAIN		(1 << 1)
+#	define	TPS_REG_PG_CORE		(1 << 0)
+#define	TPS_MASK1		0x03
+#define	TPS_MASK2		0x04
+#define	TPS_ACKINT1		0x05
+#define	TPS_ACKINT2		0x06
+#define	TPS_CHGCONFIG		0x07
+#	define	TPS_CHARGE_POR		(1 << 7)	/* 65010/65012 */
+#	define	TPS65013_AUA		(1 << 7)	/* 65011/65013 */
+#	define	TPS_CHARGE_RESET	(1 << 6)
+#	define	TPS_CHARGE_FAST		(1 << 5)
+#	define	TPS_CHARGE_CURRENT	(3 << 3)
+#	define	TPS_VBUS_500MA		(1 << 2)
+#	define	TPS_VBUS_CHARGING	(1 << 1)
+#	define	TPS_CHARGE_ENABLE	(1 << 0)
+#define	TPS_LED1_ON		0x08
+#define	TPS_LED1_PER		0x09
+#define	TPS_LED2_ON		0x0a
+#define	TPS_LED2_PER		0x0b
+#define	TPS_VDCDC1		0x0c
+#	define	TPS_ENABLE_LP		(1 << 3)
+#define	TPS_VDCDC2		0x0d
+#	define	TPS_LP_COREOFF	(1 << 7)
+#	define 	TPS_VCORE_1_8V	(7<<4)
+#	define 	TPS_VCORE_1_5V	(6 << 4)
+#	define 	TPS_VCORE_1_4V	(5 << 4)
+#	define 	TPS_VCORE_1_3V	(4 << 4)
+#	define 	TPS_VCORE_1_2V	(3 << 4)
+#	define 	TPS_VCORE_1_1V	(2 << 4)
+#	define 	TPS_VCORE_1_0V	(1 << 4)
+#	define 	TPS_VCORE_0_85V	(0 << 4)
+#	define	TPS_VCORE_LP_1_2V (3 << 2)
+#	define	TPS_VCORE_LP_1_1V (2 << 2)
+#	define	TPS_VCORE_LP_1_0V (1 << 2)
+#	define	TPS_VCORE_LP_0_85V (0 << 2)
+#	define	TPS_VIB		(1 << 1)
+#	define	TPS_VCORE_DISCH	(1 << 0)
+#define	TPS_VREGS1		0x0e
+#	define	TPS_LDO2_ENABLE	(1 << 7)
+#	define	TPS_LDO2_OFF	(1 << 6)
+#	define	TPS_VLDO2_3_0V	(3 << 4)
+#	define	TPS_VLDO2_2_75V	(2 << 4)
+#	define	TPS_VLDO2_2_5V	(1 << 4)
+#	define	TPS_VLDO2_1_8V	(0 << 4)
+#	define	TPS_LDO1_ENABLE	(1 << 3)
+#	define	TPS_LDO1_OFF	(1 << 2)
+#	define	TPS_VLDO1_3_0V	(3 << 0)
+#	define	TPS_VLDO1_2_75V	(2 << 0)
+#	define	TPS_VLDO1_2_5V	(1 << 0)
+#	define	TPS_VLDO1_ADJ	(0 << 0)
+#define	TPS_MASK3		0x0f
+#define	TPS_DEFGPIO		0x10
+
+/*
+ * ----------------------------------------------------------------------------
+ * Macros used by exported functions
+ * ----------------------------------------------------------------------------
+ */
+
+#define LED1  1
+#define LED2  2
+#define OFF   0
+#define ON    1
+#define BLINK 2
+#define GPIO1 1
+#define GPIO2 2
+#define GPIO3 3
+#define GPIO4 4
+#define LOW   0
+#define HIGH  1
+
+/*
+ * ----------------------------------------------------------------------------
+ * Exported functions
+ * ----------------------------------------------------------------------------
+ */
+
+/* Draw from VBUS:
+ *   0 mA -- DON'T DRAW (might supply power instead)
+ * 100 mA -- usb unit load (slowest charge rate)
+ * 500 mA -- usb high power (fast battery charge)
+ */
+extern int tps65010_set_vbus_draw(unsigned mA);
+
+/* tps65010_set_gpio_out_value parameter:
+ * gpio:  GPIO1, GPIO2, GPIO3 or GPIO4
+ * value: LOW or HIGH
+ */
+extern int tps65010_set_gpio_out_value(unsigned gpio, unsigned value);
+
+/* tps65010_set_led parameter:
+ * led:  LED1 or LED2
+ * mode: ON, OFF or BLINK
+ */
+extern int tps65010_set_led(unsigned led, unsigned mode);
+
+/* tps65010_set_vib parameter:
+ * value: ON or OFF
+ */
+extern int tps65010_set_vib(unsigned value);
+
+/* tps65010_set_low_pwr parameter:
+ * mode: ON or OFF
+ */
+extern int tps65010_set_low_pwr(unsigned mode);
+
+/* tps65010_config_vregs1 parameter:
+ * value to be written to VREGS1 register
+ * Note: The complete register is written, set all bits you need
+ */
+extern int tps65010_config_vregs1(unsigned value);
+
+/* tps65013_set_low_pwr parameter:
+ * mode: ON or OFF
+ */
+extern int tps65013_set_low_pwr(unsigned mode);
+
+/* tps65010_set_vdcdc2
+ *  value to be written to VDCDC2
+ */
+extern int tps65010_config_vdcdc2(unsigned value);
+
+struct i2c_client;
+
+/**
+ * struct tps65010_board - packages GPIO and LED lines
+ * @base: the GPIO number to assign to GPIO-1
+ * @outmask: bit (N-1) is set to allow GPIO-N to be used as an
+ *	(open drain) output
+ * @setup: optional callback issued once the GPIOs are valid
+ * @teardown: optional callback issued before the GPIOs are invalidated
+ * @context: optional parameter passed to setup() and teardown()
+ *
+ * Board data may be used to package the GPIO (and LED) lines for use
+ * in by the generic GPIO and LED frameworks.  The first four GPIOs
+ * starting at gpio_base are GPIO1..GPIO4.  The next two are LED1/nPG
+ * and LED2 (with hardware blinking capability, not currently exposed).
+ *
+ * The @setup callback may be used with the kind of board-specific glue
+ * which hands the (now-valid) GPIOs to other drivers, or which puts
+ * devices in their initial states using these GPIOs.
+ */
+struct tps65010_board {
+	int				base;
+	unsigned			outmask;
+
+	int		(*setup)(struct i2c_client *client, void *context);
+	int		(*teardown)(struct i2c_client *client, void *context);
+	void		*context;
+};
+
+#endif /*  __LINUX_I2C_TPS65010_H */
+
diff --git a/include/linux/i2c/tsc2007.h b/include/linux/i2c/tsc2007.h
new file mode 100644
index 0000000..4f35b6a
--- /dev/null
+++ b/include/linux/i2c/tsc2007.h
@@ -0,0 +1,22 @@
+#ifndef __LINUX_I2C_TSC2007_H
+#define __LINUX_I2C_TSC2007_H
+
+/* linux/i2c/tsc2007.h */
+
+struct tsc2007_platform_data {
+	u16	model;				/* 2007. */
+	u16	x_plate_ohms;	/* must be non-zero value */
+	u16	max_rt; /* max. resistance above which samples are ignored */
+	unsigned long poll_period; /* time (in ms) between samples */
+	int	fuzzx; /* fuzz factor for X, Y and pressure axes */
+	int	fuzzy;
+	int	fuzzz;
+
+	int	(*get_pendown_state)(struct device *);
+	/* If needed, clear 2nd level interrupt source */
+	void	(*clear_penirq)(void);
+	int	(*init_platform_hw)(void);
+	void	(*exit_platform_hw)(void);
+};
+
+#endif
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
new file mode 100644
index 0000000..9ad7828
--- /dev/null
+++ b/include/linux/i2c/twl.h
@@ -0,0 +1,876 @@
+/*
+ * twl4030.h - header for TWL4030 PM and audio CODEC device
+ *
+ * Copyright (C) 2005-2006 Texas Instruments, Inc.
+ *
+ * Based on tlv320aic23.c:
+ * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
+ *
+ */
+
+#ifndef __TWL_H_
+#define __TWL_H_
+
+#include <linux/types.h>
+#include <linux/input/matrix_keypad.h>
+
+/*
+ * Using the twl4030 core we address registers using a pair
+ *	{ module id, relative register offset }
+ * which that core then maps to the relevant
+ *	{ i2c slave, absolute register address }
+ *
+ * The module IDs are meaningful only to the twl4030 core code,
+ * which uses them as array indices to look up the first register
+ * address each module uses within a given i2c slave.
+ */
+
+/* Module IDs for similar functionalities found in twl4030/twl6030 */
+enum twl_module_ids {
+	TWL_MODULE_USB,
+	TWL_MODULE_PIH,
+	TWL_MODULE_MAIN_CHARGE,
+	TWL_MODULE_PM_MASTER,
+	TWL_MODULE_PM_RECEIVER,
+
+	TWL_MODULE_RTC,
+	TWL_MODULE_PWM,
+	TWL_MODULE_LED,
+	TWL_MODULE_SECURED_REG,
+
+	TWL_MODULE_LAST,
+};
+
+/* Modules only available in twl4030 series */
+enum twl4030_module_ids {
+	TWL4030_MODULE_AUDIO_VOICE = TWL_MODULE_LAST,
+	TWL4030_MODULE_GPIO,
+	TWL4030_MODULE_INTBR,
+	TWL4030_MODULE_TEST,
+	TWL4030_MODULE_KEYPAD,
+
+	TWL4030_MODULE_MADC,
+	TWL4030_MODULE_INTERRUPTS,
+	TWL4030_MODULE_PRECHARGE,
+	TWL4030_MODULE_BACKUP,
+	TWL4030_MODULE_INT,
+
+	TWL5031_MODULE_ACCESSORY,
+	TWL5031_MODULE_INTERRUPTS,
+
+	TWL4030_MODULE_LAST,
+};
+
+/* Modules only available in twl6030 series */
+enum twl6030_module_ids {
+	TWL6030_MODULE_ID0 = TWL_MODULE_LAST,
+	TWL6030_MODULE_ID1,
+	TWL6030_MODULE_ID2,
+	TWL6030_MODULE_GPADC,
+	TWL6030_MODULE_GASGAUGE,
+
+	TWL6030_MODULE_LAST,
+};
+
+/* Until the clients has been converted to use TWL_MODULE_LED */
+#define TWL4030_MODULE_LED	TWL_MODULE_LED
+
+#define GPIO_INTR_OFFSET	0
+#define KEYPAD_INTR_OFFSET	1
+#define BCI_INTR_OFFSET		2
+#define MADC_INTR_OFFSET	3
+#define USB_INTR_OFFSET		4
+#define CHARGERFAULT_INTR_OFFSET 5
+#define BCI_PRES_INTR_OFFSET	9
+#define USB_PRES_INTR_OFFSET	10
+#define RTC_INTR_OFFSET		11
+
+/*
+ * Offset from TWL6030_IRQ_BASE / pdata->irq_base
+ */
+#define PWR_INTR_OFFSET		0
+#define HOTDIE_INTR_OFFSET	12
+#define SMPSLDO_INTR_OFFSET	13
+#define BATDETECT_INTR_OFFSET	14
+#define SIMDETECT_INTR_OFFSET	15
+#define MMCDETECT_INTR_OFFSET	16
+#define GASGAUGE_INTR_OFFSET	17
+#define USBOTG_INTR_OFFSET	4
+#define CHARGER_INTR_OFFSET	2
+#define RSV_INTR_OFFSET		0
+
+/* INT register offsets */
+#define REG_INT_STS_A			0x00
+#define REG_INT_STS_B			0x01
+#define REG_INT_STS_C			0x02
+
+#define REG_INT_MSK_LINE_A		0x03
+#define REG_INT_MSK_LINE_B		0x04
+#define REG_INT_MSK_LINE_C		0x05
+
+#define REG_INT_MSK_STS_A		0x06
+#define REG_INT_MSK_STS_B		0x07
+#define REG_INT_MSK_STS_C		0x08
+
+/* MASK INT REG GROUP A */
+#define TWL6030_PWR_INT_MASK 		0x07
+#define TWL6030_RTC_INT_MASK 		0x18
+#define TWL6030_HOTDIE_INT_MASK 	0x20
+#define TWL6030_SMPSLDOA_INT_MASK	0xC0
+
+/* MASK INT REG GROUP B */
+#define TWL6030_SMPSLDOB_INT_MASK 	0x01
+#define TWL6030_BATDETECT_INT_MASK 	0x02
+#define TWL6030_SIMDETECT_INT_MASK 	0x04
+#define TWL6030_MMCDETECT_INT_MASK 	0x08
+#define TWL6030_GPADC_INT_MASK 		0x60
+#define TWL6030_GASGAUGE_INT_MASK 	0x80
+
+/* MASK INT REG GROUP C */
+#define TWL6030_USBOTG_INT_MASK  	0x0F
+#define TWL6030_CHARGER_CTRL_INT_MASK 	0x10
+#define TWL6030_CHARGER_FAULT_INT_MASK 	0x60
+
+#define TWL6030_MMCCTRL		0xEE
+#define VMMC_AUTO_OFF			(0x1 << 3)
+#define SW_FC				(0x1 << 2)
+#define STS_MMC			0x1
+
+#define TWL6030_CFG_INPUT_PUPD3	0xF2
+#define MMC_PU				(0x1 << 3)
+#define MMC_PD				(0x1 << 2)
+
+#define TWL_SIL_TYPE(rev)		((rev) & 0x00FFFFFF)
+#define TWL_SIL_REV(rev)		((rev) >> 24)
+#define TWL_SIL_5030			0x09002F
+#define TWL5030_REV_1_0			0x00
+#define TWL5030_REV_1_1			0x10
+#define TWL5030_REV_1_2			0x30
+
+#define TWL4030_CLASS_ID 		0x4030
+#define TWL6030_CLASS_ID 		0x6030
+unsigned int twl_rev(void);
+#define GET_TWL_REV (twl_rev())
+#define TWL_CLASS_IS(class, id)			\
+static inline int twl_class_is_ ##class(void)	\
+{						\
+	return ((id) == (GET_TWL_REV)) ? 1 : 0;	\
+}
+
+TWL_CLASS_IS(4030, TWL4030_CLASS_ID)
+TWL_CLASS_IS(6030, TWL6030_CLASS_ID)
+
+/* Set the regcache bypass for the regmap associated with the nodule */
+int twl_set_regcache_bypass(u8 mod_no, bool enable);
+
+/*
+ * Read and write several 8-bit registers at once.
+ */
+int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+
+/*
+ * Read and write single 8-bit registers
+ */
+static inline int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg) {
+	return twl_i2c_write(mod_no, &val, reg, 1);
+}
+
+static inline int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg) {
+	return twl_i2c_read(mod_no, val, reg, 1);
+}
+
+static inline int twl_i2c_write_u16(u8 mod_no, u16 val, u8 reg) {
+	val = cpu_to_le16(val);
+	return twl_i2c_write(mod_no, (u8*) &val, reg, 2);
+}
+
+static inline int twl_i2c_read_u16(u8 mod_no, u16 *val, u8 reg) {
+	int ret;
+	ret = twl_i2c_read(mod_no, (u8*) val, reg, 2);
+	*val = le16_to_cpu(*val);
+	return ret;
+}
+
+int twl_get_type(void);
+int twl_get_version(void);
+int twl_get_hfclk_rate(void);
+
+int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
+int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
+
+/* Card detect Configuration for MMC1 Controller on OMAP4 */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect_config(void);
+#else
+static inline int twl6030_mmc_card_detect_config(void)
+{
+	pr_debug("twl6030_mmc_card_detect_config not supported\n");
+	return 0;
+}
+#endif
+
+/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect(struct device *dev, int slot);
+#else
+static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
+{
+	pr_debug("Call back twl6030_mmc_card_detect not supported\n");
+	return -EIO;
+}
+#endif
+/*----------------------------------------------------------------------*/
+
+/*
+ * NOTE:  at up to 1024 registers, this is a big chip.
+ *
+ * Avoid putting register declarations in this file, instead of into
+ * a driver-private file, unless some of the registers in a block
+ * need to be shared with other drivers.  One example is blocks that
+ * have Secondary IRQ Handler (SIH) registers.
+ */
+
+#define TWL4030_SIH_CTRL_EXCLEN_MASK	BIT(0)
+#define TWL4030_SIH_CTRL_PENDDIS_MASK	BIT(1)
+#define TWL4030_SIH_CTRL_COR_MASK	BIT(2)
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
+ */
+
+#define REG_GPIODATAIN1			0x0
+#define REG_GPIODATAIN2			0x1
+#define REG_GPIODATAIN3			0x2
+#define REG_GPIODATADIR1		0x3
+#define REG_GPIODATADIR2		0x4
+#define REG_GPIODATADIR3		0x5
+#define REG_GPIODATAOUT1		0x6
+#define REG_GPIODATAOUT2		0x7
+#define REG_GPIODATAOUT3		0x8
+#define REG_CLEARGPIODATAOUT1		0x9
+#define REG_CLEARGPIODATAOUT2		0xA
+#define REG_CLEARGPIODATAOUT3		0xB
+#define REG_SETGPIODATAOUT1		0xC
+#define REG_SETGPIODATAOUT2		0xD
+#define REG_SETGPIODATAOUT3		0xE
+#define REG_GPIO_DEBEN1			0xF
+#define REG_GPIO_DEBEN2			0x10
+#define REG_GPIO_DEBEN3			0x11
+#define REG_GPIO_CTRL			0x12
+#define REG_GPIOPUPDCTR1		0x13
+#define REG_GPIOPUPDCTR2		0x14
+#define REG_GPIOPUPDCTR3		0x15
+#define REG_GPIOPUPDCTR4		0x16
+#define REG_GPIOPUPDCTR5		0x17
+#define REG_GPIO_ISR1A			0x19
+#define REG_GPIO_ISR2A			0x1A
+#define REG_GPIO_ISR3A			0x1B
+#define REG_GPIO_IMR1A			0x1C
+#define REG_GPIO_IMR2A			0x1D
+#define REG_GPIO_IMR3A			0x1E
+#define REG_GPIO_ISR1B			0x1F
+#define REG_GPIO_ISR2B			0x20
+#define REG_GPIO_ISR3B			0x21
+#define REG_GPIO_IMR1B			0x22
+#define REG_GPIO_IMR2B			0x23
+#define REG_GPIO_IMR3B			0x24
+#define REG_GPIO_EDR1			0x28
+#define REG_GPIO_EDR2			0x29
+#define REG_GPIO_EDR3			0x2A
+#define REG_GPIO_EDR4			0x2B
+#define REG_GPIO_EDR5			0x2C
+#define REG_GPIO_SIH_CTRL		0x2D
+
+/* Up to 18 signals are available as GPIOs, when their
+ * pins are not assigned to another use (such as ULPI/USB).
+ */
+#define TWL4030_GPIO_MAX		18
+
+/*----------------------------------------------------------------------*/
+
+/*Interface Bit Register (INTBR) offsets
+ *(Use TWL_4030_MODULE_INTBR)
+ */
+
+#define REG_IDCODE_7_0			0x00
+#define REG_IDCODE_15_8			0x01
+#define REG_IDCODE_16_23		0x02
+#define REG_IDCODE_31_24		0x03
+#define REG_GPPUPDCTR1			0x0F
+#define REG_UNLOCK_TEST_REG		0x12
+
+/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */
+
+#define I2C_SCL_CTRL_PU			BIT(0)
+#define I2C_SDA_CTRL_PU			BIT(2)
+#define SR_I2C_SCL_CTRL_PU		BIT(4)
+#define SR_I2C_SDA_CTRL_PU		BIT(6)
+
+#define TWL_EEPROM_R_UNLOCK		0x49
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Keypad register offsets (use TWL4030_MODULE_KEYPAD)
+ * ... SIH/interrupt only
+ */
+
+#define TWL4030_KEYPAD_KEYP_ISR1	0x11
+#define TWL4030_KEYPAD_KEYP_IMR1	0x12
+#define TWL4030_KEYPAD_KEYP_ISR2	0x13
+#define TWL4030_KEYPAD_KEYP_IMR2	0x14
+#define TWL4030_KEYPAD_KEYP_SIR		0x15	/* test register */
+#define TWL4030_KEYPAD_KEYP_EDR		0x16
+#define TWL4030_KEYPAD_KEYP_SIH_CTRL	0x17
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
+ * ... SIH/interrupt only
+ */
+
+#define TWL4030_MADC_ISR1		0x61
+#define TWL4030_MADC_IMR1		0x62
+#define TWL4030_MADC_ISR2		0x63
+#define TWL4030_MADC_IMR2		0x64
+#define TWL4030_MADC_SIR		0x65	/* test register */
+#define TWL4030_MADC_EDR		0x66
+#define TWL4030_MADC_SIH_CTRL		0x67
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
+ */
+
+#define TWL4030_INTERRUPTS_BCIISR1A	0x0
+#define TWL4030_INTERRUPTS_BCIISR2A	0x1
+#define TWL4030_INTERRUPTS_BCIIMR1A	0x2
+#define TWL4030_INTERRUPTS_BCIIMR2A	0x3
+#define TWL4030_INTERRUPTS_BCIISR1B	0x4
+#define TWL4030_INTERRUPTS_BCIISR2B	0x5
+#define TWL4030_INTERRUPTS_BCIIMR1B	0x6
+#define TWL4030_INTERRUPTS_BCIIMR2B	0x7
+#define TWL4030_INTERRUPTS_BCISIR1	0x8	/* test register */
+#define TWL4030_INTERRUPTS_BCISIR2	0x9	/* test register */
+#define TWL4030_INTERRUPTS_BCIEDR1	0xa
+#define TWL4030_INTERRUPTS_BCIEDR2	0xb
+#define TWL4030_INTERRUPTS_BCIEDR3	0xc
+#define TWL4030_INTERRUPTS_BCISIHCTRL	0xd
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Power Interrupt block register offsets (use TWL4030_MODULE_INT)
+ */
+
+#define TWL4030_INT_PWR_ISR1		0x0
+#define TWL4030_INT_PWR_IMR1		0x1
+#define TWL4030_INT_PWR_ISR2		0x2
+#define TWL4030_INT_PWR_IMR2		0x3
+#define TWL4030_INT_PWR_SIR		0x4	/* test register */
+#define TWL4030_INT_PWR_EDR1		0x5
+#define TWL4030_INT_PWR_EDR2		0x6
+#define TWL4030_INT_PWR_SIH_CTRL	0x7
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Accessory Interrupts
+ */
+#define TWL5031_ACIIMR_LSB		0x05
+#define TWL5031_ACIIMR_MSB		0x06
+#define TWL5031_ACIIDR_LSB		0x07
+#define TWL5031_ACIIDR_MSB		0x08
+#define TWL5031_ACCISR1			0x0F
+#define TWL5031_ACCIMR1			0x10
+#define TWL5031_ACCISR2			0x11
+#define TWL5031_ACCIMR2			0x12
+#define TWL5031_ACCSIR			0x13
+#define TWL5031_ACCEDR1			0x14
+#define TWL5031_ACCSIHCTRL		0x15
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Battery Charger Controller
+ */
+
+#define TWL5031_INTERRUPTS_BCIISR1	0x0
+#define TWL5031_INTERRUPTS_BCIIMR1	0x1
+#define TWL5031_INTERRUPTS_BCIISR2	0x2
+#define TWL5031_INTERRUPTS_BCIIMR2	0x3
+#define TWL5031_INTERRUPTS_BCISIR	0x4
+#define TWL5031_INTERRUPTS_BCIEDR1	0x5
+#define TWL5031_INTERRUPTS_BCIEDR2	0x6
+#define TWL5031_INTERRUPTS_BCISIHCTRL	0x7
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * PM Master module register offsets (use TWL4030_MODULE_PM_MASTER)
+ */
+
+#define TWL4030_PM_MASTER_CFG_P1_TRANSITION	0x00
+#define TWL4030_PM_MASTER_CFG_P2_TRANSITION	0x01
+#define TWL4030_PM_MASTER_CFG_P3_TRANSITION	0x02
+#define TWL4030_PM_MASTER_CFG_P123_TRANSITION	0x03
+#define TWL4030_PM_MASTER_STS_BOOT		0x04
+#define TWL4030_PM_MASTER_CFG_BOOT		0x05
+#define TWL4030_PM_MASTER_SHUNDAN		0x06
+#define TWL4030_PM_MASTER_BOOT_BCI		0x07
+#define TWL4030_PM_MASTER_CFG_PWRANA1		0x08
+#define TWL4030_PM_MASTER_CFG_PWRANA2		0x09
+#define TWL4030_PM_MASTER_BACKUP_MISC_STS	0x0b
+#define TWL4030_PM_MASTER_BACKUP_MISC_CFG	0x0c
+#define TWL4030_PM_MASTER_BACKUP_MISC_TST	0x0d
+#define TWL4030_PM_MASTER_PROTECT_KEY		0x0e
+#define TWL4030_PM_MASTER_STS_HW_CONDITIONS	0x0f
+#define TWL4030_PM_MASTER_P1_SW_EVENTS		0x10
+#define TWL4030_PM_MASTER_P2_SW_EVENTS		0x11
+#define TWL4030_PM_MASTER_P3_SW_EVENTS		0x12
+#define TWL4030_PM_MASTER_STS_P123_STATE	0x13
+#define TWL4030_PM_MASTER_PB_CFG		0x14
+#define TWL4030_PM_MASTER_PB_WORD_MSB		0x15
+#define TWL4030_PM_MASTER_PB_WORD_LSB		0x16
+#define TWL4030_PM_MASTER_SEQ_ADD_W2P		0x1c
+#define TWL4030_PM_MASTER_SEQ_ADD_P2A		0x1d
+#define TWL4030_PM_MASTER_SEQ_ADD_A2W		0x1e
+#define TWL4030_PM_MASTER_SEQ_ADD_A2S		0x1f
+#define TWL4030_PM_MASTER_SEQ_ADD_S2A12		0x20
+#define TWL4030_PM_MASTER_SEQ_ADD_S2A3		0x21
+#define TWL4030_PM_MASTER_SEQ_ADD_WARM		0x22
+#define TWL4030_PM_MASTER_MEMORY_ADDRESS	0x23
+#define TWL4030_PM_MASTER_MEMORY_DATA		0x24
+
+#define TWL4030_PM_MASTER_KEY_CFG1		0xc0
+#define TWL4030_PM_MASTER_KEY_CFG2		0x0c
+
+#define TWL4030_PM_MASTER_KEY_TST1		0xe0
+#define TWL4030_PM_MASTER_KEY_TST2		0x0e
+
+#define TWL4030_PM_MASTER_GLOBAL_TST		0xb6
+
+/*----------------------------------------------------------------------*/
+
+/* Power bus message definitions */
+
+/* The TWL4030/5030 splits its power-management resources (the various
+ * regulators, clock and reset lines) into 3 processor groups - P1, P2 and
+ * P3. These groups can then be configured to transition between sleep, wait-on
+ * and active states by sending messages to the power bus.  See Section 5.4.2
+ * Power Resources of TWL4030 TRM
+ */
+
+/* Processor groups */
+#define DEV_GRP_NULL		0x0
+#define DEV_GRP_P1		0x1	/* P1: all OMAP devices */
+#define DEV_GRP_P2		0x2	/* P2: all Modem devices */
+#define DEV_GRP_P3		0x4	/* P3: all peripheral devices */
+
+/* Resource groups */
+#define RES_GRP_RES		0x0	/* Reserved */
+#define RES_GRP_PP		0x1	/* Power providers */
+#define RES_GRP_RC		0x2	/* Reset and control */
+#define RES_GRP_PP_RC		0x3
+#define RES_GRP_PR		0x4	/* Power references */
+#define RES_GRP_PP_PR		0x5
+#define RES_GRP_RC_PR		0x6
+#define RES_GRP_ALL		0x7	/* All resource groups */
+
+#define RES_TYPE2_R0		0x0
+#define RES_TYPE2_R1		0x1
+#define RES_TYPE2_R2		0x2
+
+#define RES_TYPE_R0		0x0
+#define RES_TYPE_ALL		0x7
+
+/* Resource states */
+#define RES_STATE_WRST		0xF
+#define RES_STATE_ACTIVE	0xE
+#define RES_STATE_SLEEP		0x8
+#define RES_STATE_OFF		0x0
+
+/* Power resources */
+
+/* Power providers */
+#define RES_VAUX1               1
+#define RES_VAUX2               2
+#define RES_VAUX3               3
+#define RES_VAUX4               4
+#define RES_VMMC1               5
+#define RES_VMMC2               6
+#define RES_VPLL1               7
+#define RES_VPLL2               8
+#define RES_VSIM                9
+#define RES_VDAC                10
+#define RES_VINTANA1            11
+#define RES_VINTANA2            12
+#define RES_VINTDIG             13
+#define RES_VIO                 14
+#define RES_VDD1                15
+#define RES_VDD2                16
+#define RES_VUSB_1V5            17
+#define RES_VUSB_1V8            18
+#define RES_VUSB_3V1            19
+#define RES_VUSBCP              20
+#define RES_REGEN               21
+/* Reset and control */
+#define RES_NRES_PWRON          22
+#define RES_CLKEN               23
+#define RES_SYSEN               24
+#define RES_HFCLKOUT            25
+#define RES_32KCLKOUT           26
+#define RES_RESET               27
+/* Power Reference */
+#define RES_MAIN_REF            28
+
+#define TOTAL_RESOURCES		28
+/*
+ * Power Bus Message Format ... these can be sent individually by Linux,
+ * but are usually part of downloaded scripts that are run when various
+ * power events are triggered.
+ *
+ *  Broadcast Message (16 Bits):
+ *    DEV_GRP[15:13] MT[12]  RES_GRP[11:9]  RES_TYPE2[8:7] RES_TYPE[6:4]
+ *    RES_STATE[3:0]
+ *
+ *  Singular Message (16 Bits):
+ *    DEV_GRP[15:13] MT[12]  RES_ID[11:4]  RES_STATE[3:0]
+ */
+
+#define MSG_BROADCAST(devgrp, grp, type, type2, state) \
+	( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \
+	| (type) << 4 | (state))
+
+#define MSG_SINGULAR(devgrp, id, state) \
+	((devgrp) << 13 | 0 << 12 | (id) << 4 | (state))
+
+#define MSG_BROADCAST_ALL(devgrp, state) \
+	((devgrp) << 5 | (state))
+
+#define MSG_BROADCAST_REF MSG_BROADCAST_ALL
+#define MSG_BROADCAST_PROV MSG_BROADCAST_ALL
+#define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL
+/*----------------------------------------------------------------------*/
+
+struct twl4030_clock_init_data {
+	bool ck32k_lowpwr_enable;
+};
+
+struct twl4030_bci_platform_data {
+	int *battery_tmp_tbl;
+	unsigned int tblsize;
+	int	bb_uvolt;	/* voltage to charge backup battery */
+	int	bb_uamp;	/* current for backup battery charging */
+};
+
+/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
+struct twl4030_gpio_platform_data {
+	/* package the two LED signals as output-only GPIOs? */
+	bool		use_leds;
+
+	/* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
+	u8		mmc_cd;
+
+	/* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */
+	u32		debounce;
+
+	/* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
+	 * should be enabled.  Else, if that bit is set in "pulldowns",
+	 * that pulldown is enabled.  Don't waste power by letting any
+	 * digital inputs float...
+	 */
+	u32		pullups;
+	u32		pulldowns;
+
+	int		(*setup)(struct device *dev,
+				unsigned gpio, unsigned ngpio);
+	int		(*teardown)(struct device *dev,
+				unsigned gpio, unsigned ngpio);
+};
+
+struct twl4030_madc_platform_data {
+	int		irq_line;
+};
+
+/* Boards have unique mappings of {row, col} --> keycode.
+ * Column and row are 8 bits each, but range only from 0..7.
+ * a PERSISTENT_KEY is "always on" and never reported.
+ */
+#define PERSISTENT_KEY(r, c)	KEY((r), (c), KEY_RESERVED)
+
+struct twl4030_keypad_data {
+	const struct matrix_keymap_data *keymap_data;
+	unsigned rows;
+	unsigned cols;
+	bool rep;
+};
+
+enum twl4030_usb_mode {
+	T2_USB_MODE_ULPI = 1,
+	T2_USB_MODE_CEA2011_3PIN = 2,
+};
+
+struct twl4030_usb_data {
+	enum twl4030_usb_mode	usb_mode;
+	unsigned long		features;
+
+	int		(*phy_init)(struct device *dev);
+	int		(*phy_exit)(struct device *dev);
+	/* Power on/off the PHY */
+	int		(*phy_power)(struct device *dev, int iD, int on);
+	/* enable/disable  phy clocks */
+	int		(*phy_set_clock)(struct device *dev, int on);
+	/* suspend/resume of phy */
+	int		(*phy_suspend)(struct device *dev, int suspend);
+};
+
+struct twl4030_ins {
+	u16 pmb_message;
+	u8 delay;
+};
+
+struct twl4030_script {
+	struct twl4030_ins *script;
+	unsigned size;
+	u8 flags;
+#define TWL4030_WRST_SCRIPT	(1<<0)
+#define TWL4030_WAKEUP12_SCRIPT	(1<<1)
+#define TWL4030_WAKEUP3_SCRIPT	(1<<2)
+#define TWL4030_SLEEP_SCRIPT	(1<<3)
+};
+
+struct twl4030_resconfig {
+	u8 resource;
+	u8 devgroup;	/* Processor group that Power resource belongs to */
+	u8 type;	/* Power resource addressed, 6 / broadcast message */
+	u8 type2;	/* Power resource addressed, 3 / broadcast message */
+	u8 remap_off;	/* off state remapping */
+	u8 remap_sleep;	/* sleep state remapping */
+};
+
+struct twl4030_power_data {
+	struct twl4030_script **scripts;
+	unsigned num;
+	struct twl4030_resconfig *resource_config;
+	struct twl4030_resconfig *board_config;
+#define TWL4030_RESCONFIG_UNDEF	((u8)-1)
+	bool use_poweroff;	/* Board is wired for TWL poweroff */
+	bool ac_charger_quirk;	/* Disable AC charger on board */
+};
+
+extern int twl4030_remove_script(u8 flags);
+extern void twl4030_power_off(void);
+
+struct twl4030_codec_data {
+	unsigned int digimic_delay; /* in ms */
+	unsigned int ramp_delay_value;
+	unsigned int offset_cncl_path;
+	unsigned int hs_extmute:1;
+	int hs_extmute_gpio;
+};
+
+struct twl4030_vibra_data {
+	unsigned int	coexist;
+};
+
+struct twl4030_audio_data {
+	unsigned int	audio_mclk;
+	struct twl4030_codec_data *codec;
+	struct twl4030_vibra_data *vibra;
+
+	/* twl6040 */
+	int audpwron_gpio;	/* audio power-on gpio */
+	int naudint_irq;	/* audio interrupt */
+	unsigned int irq_base;
+};
+
+struct twl4030_platform_data {
+	struct twl4030_clock_init_data		*clock;
+	struct twl4030_bci_platform_data	*bci;
+	struct twl4030_gpio_platform_data	*gpio;
+	struct twl4030_madc_platform_data	*madc;
+	struct twl4030_keypad_data		*keypad;
+	struct twl4030_usb_data			*usb;
+	struct twl4030_power_data		*power;
+	struct twl4030_audio_data		*audio;
+
+	/* Common LDO regulators for TWL4030/TWL6030 */
+	struct regulator_init_data		*vdac;
+	struct regulator_init_data		*vaux1;
+	struct regulator_init_data		*vaux2;
+	struct regulator_init_data		*vaux3;
+	struct regulator_init_data		*vdd1;
+	struct regulator_init_data		*vdd2;
+	struct regulator_init_data		*vdd3;
+	/* TWL4030 LDO regulators */
+	struct regulator_init_data		*vpll1;
+	struct regulator_init_data		*vpll2;
+	struct regulator_init_data		*vmmc1;
+	struct regulator_init_data		*vmmc2;
+	struct regulator_init_data		*vsim;
+	struct regulator_init_data		*vaux4;
+	struct regulator_init_data		*vio;
+	struct regulator_init_data		*vintana1;
+	struct regulator_init_data		*vintana2;
+	struct regulator_init_data		*vintdig;
+	/* TWL6030 LDO regulators */
+	struct regulator_init_data              *vmmc;
+	struct regulator_init_data              *vpp;
+	struct regulator_init_data              *vusim;
+	struct regulator_init_data              *vana;
+	struct regulator_init_data              *vcxio;
+	struct regulator_init_data              *vusb;
+	struct regulator_init_data		*clk32kg;
+	struct regulator_init_data              *v1v8;
+	struct regulator_init_data              *v2v1;
+	/* TWL6032 LDO regulators */
+	struct regulator_init_data		*ldo1;
+	struct regulator_init_data		*ldo2;
+	struct regulator_init_data		*ldo3;
+	struct regulator_init_data		*ldo4;
+	struct regulator_init_data		*ldo5;
+	struct regulator_init_data		*ldo6;
+	struct regulator_init_data		*ldo7;
+	struct regulator_init_data		*ldoln;
+	struct regulator_init_data		*ldousb;
+	/* TWL6032 DCDC regulators */
+	struct regulator_init_data		*smps3;
+	struct regulator_init_data		*smps4;
+	struct regulator_init_data		*vio6025;
+};
+
+struct twl_regulator_driver_data {
+	int		(*set_voltage)(void *data, int target_uV);
+	int		(*get_voltage)(void *data);
+	void		*data;
+	unsigned long	features;
+};
+/* chip-specific feature flags, for twl_regulator_driver_data.features */
+#define TWL4030_VAUX2		BIT(0)	/* pre-5030 voltage ranges */
+#define TPS_SUBSET		BIT(1)	/* tps659[23]0 have fewer LDOs */
+#define TWL5031			BIT(2)  /* twl5031 has different registers */
+#define TWL6030_CLASS		BIT(3)	/* TWL6030 class */
+#define TWL6032_SUBCLASS	BIT(4)  /* TWL6032 has changed registers */
+#define TWL4030_ALLOW_UNSUPPORTED BIT(5) /* Some voltages are possible
+					  * but not officially supported.
+					  * This flag is necessary to
+					  * enable them.
+					  */
+
+/*----------------------------------------------------------------------*/
+
+int twl4030_sih_setup(struct device *dev, int module, int irq_base);
+
+/* Offsets to Power Registers */
+#define TWL4030_VDAC_DEV_GRP		0x3B
+#define TWL4030_VDAC_DEDICATED		0x3E
+#define TWL4030_VAUX1_DEV_GRP		0x17
+#define TWL4030_VAUX1_DEDICATED		0x1A
+#define TWL4030_VAUX2_DEV_GRP		0x1B
+#define TWL4030_VAUX2_DEDICATED		0x1E
+#define TWL4030_VAUX3_DEV_GRP		0x1F
+#define TWL4030_VAUX3_DEDICATED		0x22
+
+static inline int twl4030charger_usb_en(int enable) { return 0; }
+
+/*----------------------------------------------------------------------*/
+
+/* Linux-specific regulator identifiers ... for now, we only support
+ * the LDOs, and leave the three buck converters alone.  VDD1 and VDD2
+ * need to tie into hardware based voltage scaling (cpufreq etc), while
+ * VIO is generally fixed.
+ */
+
+/* TWL4030 SMPS/LDO's */
+/* EXTERNAL dc-to-dc buck converters */
+#define TWL4030_REG_VDD1	0
+#define TWL4030_REG_VDD2	1
+#define TWL4030_REG_VIO		2
+
+/* EXTERNAL LDOs */
+#define TWL4030_REG_VDAC	3
+#define TWL4030_REG_VPLL1	4
+#define TWL4030_REG_VPLL2	5	/* not on all chips */
+#define TWL4030_REG_VMMC1	6
+#define TWL4030_REG_VMMC2	7	/* not on all chips */
+#define TWL4030_REG_VSIM	8	/* not on all chips */
+#define TWL4030_REG_VAUX1	9	/* not on all chips */
+#define TWL4030_REG_VAUX2_4030	10	/* (twl4030-specific) */
+#define TWL4030_REG_VAUX2	11	/* (twl5030 and newer) */
+#define TWL4030_REG_VAUX3	12	/* not on all chips */
+#define TWL4030_REG_VAUX4	13	/* not on all chips */
+
+/* INTERNAL LDOs */
+#define TWL4030_REG_VINTANA1	14
+#define TWL4030_REG_VINTANA2	15
+#define TWL4030_REG_VINTDIG	16
+#define TWL4030_REG_VUSB1V5	17
+#define TWL4030_REG_VUSB1V8	18
+#define TWL4030_REG_VUSB3V1	19
+
+/* TWL6030 SMPS/LDO's */
+/* EXTERNAL dc-to-dc buck convertor controllable via SR */
+#define TWL6030_REG_VDD1	30
+#define TWL6030_REG_VDD2	31
+#define TWL6030_REG_VDD3	32
+
+/* Non SR compliant dc-to-dc buck convertors */
+#define TWL6030_REG_VMEM	33
+#define TWL6030_REG_V2V1	34
+#define TWL6030_REG_V1V29	35
+#define TWL6030_REG_V1V8	36
+
+/* EXTERNAL LDOs */
+#define TWL6030_REG_VAUX1_6030	37
+#define TWL6030_REG_VAUX2_6030	38
+#define TWL6030_REG_VAUX3_6030	39
+#define TWL6030_REG_VMMC	40
+#define TWL6030_REG_VPP		41
+#define TWL6030_REG_VUSIM	42
+#define TWL6030_REG_VANA	43
+#define TWL6030_REG_VCXIO	44
+#define TWL6030_REG_VDAC	45
+#define TWL6030_REG_VUSB	46
+
+/* INTERNAL LDOs */
+#define TWL6030_REG_VRTC	47
+#define TWL6030_REG_CLK32KG	48
+
+/* LDOs on 6025 have different names */
+#define TWL6032_REG_LDO2	49
+#define TWL6032_REG_LDO4	50
+#define TWL6032_REG_LDO3	51
+#define TWL6032_REG_LDO5	52
+#define TWL6032_REG_LDO1	53
+#define TWL6032_REG_LDO7	54
+#define TWL6032_REG_LDO6	55
+#define TWL6032_REG_LDOLN	56
+#define TWL6032_REG_LDOUSB	57
+
+/* 6025 DCDC supplies */
+#define TWL6032_REG_SMPS3	58
+#define TWL6032_REG_SMPS4	59
+#define TWL6032_REG_VIO		60
+
+
+#endif /* End of __TWL4030_H */
diff --git a/include/linux/i2c/twl4030-madc.h b/include/linux/i2c/twl4030-madc.h
new file mode 100644
index 0000000..1c0134d
--- /dev/null
+++ b/include/linux/i2c/twl4030-madc.h
@@ -0,0 +1,147 @@
+/*
+ * twl4030_madc.h - Header for TWL4030 MADC
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ * J Keerthy <j-keerthy@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef _TWL4030_MADC_H
+#define _TWL4030_MADC_H
+
+struct twl4030_madc_conversion_method {
+	u8 sel;
+	u8 avg;
+	u8 rbase;
+	u8 ctrl;
+};
+
+#define TWL4030_MADC_MAX_CHANNELS 16
+
+
+/*
+ * twl4030_madc_request- madc request packet for channel conversion
+ * @channels:	16 bit bitmap for individual channels
+ * @do_avgP:	sample the input channel for 4 consecutive cycles
+ * @method:	RT, SW1, SW2
+ * @type:	Polling or interrupt based method
+ * @raw:	Return raw value, do not convert it
+ */
+
+struct twl4030_madc_request {
+	unsigned long channels;
+	bool do_avg;
+	u16 method;
+	u16 type;
+	bool active;
+	bool result_pending;
+	bool raw;
+	int rbuf[TWL4030_MADC_MAX_CHANNELS];
+	void (*func_cb)(int len, int channels, int *buf);
+};
+
+enum conversion_methods {
+	TWL4030_MADC_RT,
+	TWL4030_MADC_SW1,
+	TWL4030_MADC_SW2,
+	TWL4030_MADC_NUM_METHODS
+};
+
+enum sample_type {
+	TWL4030_MADC_WAIT,
+	TWL4030_MADC_IRQ_ONESHOT,
+	TWL4030_MADC_IRQ_REARM
+};
+
+#define TWL4030_MADC_CTRL1		0x00
+#define TWL4030_MADC_CTRL2		0x01
+
+#define TWL4030_MADC_RTSELECT_LSB	0x02
+#define TWL4030_MADC_SW1SELECT_LSB	0x06
+#define TWL4030_MADC_SW2SELECT_LSB	0x0A
+
+#define TWL4030_MADC_RTAVERAGE_LSB	0x04
+#define TWL4030_MADC_SW1AVERAGE_LSB	0x08
+#define TWL4030_MADC_SW2AVERAGE_LSB	0x0C
+
+#define TWL4030_MADC_CTRL_SW1		0x12
+#define TWL4030_MADC_CTRL_SW2		0x13
+
+#define TWL4030_MADC_RTCH0_LSB		0x17
+#define TWL4030_MADC_GPCH0_LSB		0x37
+
+#define TWL4030_MADC_MADCON	(1 << 0)	/* MADC power on */
+#define TWL4030_MADC_BUSY	(1 << 0)	/* MADC busy */
+/* MADC conversion completion */
+#define TWL4030_MADC_EOC_SW	(1 << 1)
+/* MADC SWx start conversion */
+#define TWL4030_MADC_SW_START	(1 << 5)
+#define TWL4030_MADC_ADCIN0	(1 << 0)
+#define TWL4030_MADC_ADCIN1	(1 << 1)
+#define TWL4030_MADC_ADCIN2	(1 << 2)
+#define TWL4030_MADC_ADCIN3	(1 << 3)
+#define TWL4030_MADC_ADCIN4	(1 << 4)
+#define TWL4030_MADC_ADCIN5	(1 << 5)
+#define TWL4030_MADC_ADCIN6	(1 << 6)
+#define TWL4030_MADC_ADCIN7	(1 << 7)
+#define TWL4030_MADC_ADCIN8	(1 << 8)
+#define TWL4030_MADC_ADCIN9	(1 << 9)
+#define TWL4030_MADC_ADCIN10	(1 << 10)
+#define TWL4030_MADC_ADCIN11	(1 << 11)
+#define TWL4030_MADC_ADCIN12	(1 << 12)
+#define TWL4030_MADC_ADCIN13	(1 << 13)
+#define TWL4030_MADC_ADCIN14	(1 << 14)
+#define TWL4030_MADC_ADCIN15	(1 << 15)
+
+/* Fixed channels */
+#define TWL4030_MADC_BTEMP	TWL4030_MADC_ADCIN1
+#define TWL4030_MADC_VBUS	TWL4030_MADC_ADCIN8
+#define TWL4030_MADC_VBKB	TWL4030_MADC_ADCIN9
+#define TWL4030_MADC_ICHG	TWL4030_MADC_ADCIN10
+#define TWL4030_MADC_VCHG	TWL4030_MADC_ADCIN11
+#define TWL4030_MADC_VBAT	TWL4030_MADC_ADCIN12
+
+/* Step size and prescaler ratio */
+#define TEMP_STEP_SIZE          147
+#define TEMP_PSR_R              100
+#define CURR_STEP_SIZE		147
+#define CURR_PSR_R1		44
+#define CURR_PSR_R2		88
+
+#define TWL4030_BCI_BCICTL1	0x23
+#define TWL4030_BCI_CGAIN	0x020
+#define TWL4030_BCI_MESBAT	(1 << 1)
+#define TWL4030_BCI_TYPEN	(1 << 4)
+#define TWL4030_BCI_ITHEN	(1 << 3)
+
+#define REG_BCICTL2             0x024
+#define TWL4030_BCI_ITHSENS	0x007
+
+/* Register and bits for GPBR1 register */
+#define TWL4030_REG_GPBR1		0x0c
+#define TWL4030_GPBR1_MADC_HFCLK_EN	(1 << 7)
+
+struct twl4030_madc_user_parms {
+	int channel;
+	int average;
+	int status;
+	u16 result;
+};
+
+int twl4030_madc_conversion(struct twl4030_madc_request *conv);
+int twl4030_get_madc_conversion(int channel_no);
+#endif