Merge branch 'master' of git://git.denx.de/u-boot-arm
diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c
index 5617a41..bd65a08 100644
--- a/arch/arm/cpu/armv7/mx6/clock.c
+++ b/arch/arm/cpu/armv7/mx6/clock.c
@@ -409,20 +409,15 @@
u32 imx_get_fecclk(void)
{
- return decode_pll(PLL_ENET, MXC_HCLK);
+ return mxc_get_clock(MXC_IPG_CLK);
}
-int enable_sata_clock(void)
+static int enable_enet_pll(uint32_t en)
{
- u32 reg = 0;
- s32 timeout = 100000;
struct mxc_ccm_reg *const imx_ccm
= (struct mxc_ccm_reg *) CCM_BASE_ADDR;
-
- /* Enable sata clock */
- reg = readl(&imx_ccm->CCGR5); /* CCGR5 */
- reg |= MXC_CCM_CCGR5_SATA_MASK;
- writel(reg, &imx_ccm->CCGR5);
+ s32 timeout = 100000;
+ u32 reg = 0;
/* Enable PLLs */
reg = readl(&imx_ccm->analog_pll_enet);
@@ -437,10 +432,70 @@
return -EIO;
reg &= ~BM_ANADIG_PLL_SYS_BYPASS;
writel(reg, &imx_ccm->analog_pll_enet);
- reg |= BM_ANADIG_PLL_ENET_ENABLE_SATA;
+ reg |= en;
writel(reg, &imx_ccm->analog_pll_enet);
+ return 0;
+}
- return 0 ;
+static void ungate_sata_clock(void)
+{
+ struct mxc_ccm_reg *const imx_ccm =
+ (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* Enable SATA clock. */
+ setbits_le32(&imx_ccm->CCGR5, MXC_CCM_CCGR5_SATA_MASK);
+}
+
+static void ungate_pcie_clock(void)
+{
+ struct mxc_ccm_reg *const imx_ccm =
+ (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* Enable PCIe clock. */
+ setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_PCIE_MASK);
+}
+
+int enable_sata_clock(void)
+{
+ ungate_sata_clock();
+ return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA);
+}
+
+int enable_pcie_clock(void)
+{
+ struct anatop_regs *anatop_regs =
+ (struct anatop_regs *)ANATOP_BASE_ADDR;
+ struct mxc_ccm_reg *ccm_regs = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /*
+ * Here be dragons!
+ *
+ * The register ANATOP_MISC1 is not documented in the Freescale
+ * MX6RM. The register that is mapped in the ANATOP space and
+ * marked as ANATOP_MISC1 is actually documented in the PMU section
+ * of the datasheet as PMU_MISC1.
+ *
+ * Switch LVDS clock source to SATA (0xb), disable clock INPUT and
+ * enable clock OUTPUT. This is important for PCI express link that
+ * is clocked from the i.MX6.
+ */
+#define ANADIG_ANA_MISC1_LVDSCLK1_IBEN (1 << 12)
+#define ANADIG_ANA_MISC1_LVDSCLK1_OBEN (1 << 10)
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK 0x0000001F
+ clrsetbits_le32(&anatop_regs->ana_misc1,
+ ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
+ ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
+ ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
+
+ /* PCIe reference clock sourced from AXI. */
+ clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
+
+ /* Party time! Ungate the clock to the PCIe. */
+ ungate_sata_clock();
+ ungate_pcie_clock();
+
+ return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA |
+ BM_ANADIG_PLL_ENET_ENABLE_PCIE);
}
unsigned int mxc_get_clock(enum mxc_clock clk)
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index 0208cba..1725279 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -8,6 +8,8 @@
*/
#include <common.h>
+#include <asm/armv7.h>
+#include <asm/pl310.h>
#include <asm/errno.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
@@ -41,14 +43,19 @@
if (type != MXC_CPU_MX6SL) {
reg = readl(&anatop->digprog);
+ struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
+ u32 cfg = readl(&scu->config) & 3;
type = ((reg >> 16) & 0xff);
if (type == MXC_CPU_MX6DL) {
- struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
- u32 cfg = readl(&scu->config) & 3;
-
if (!cfg)
type = MXC_CPU_MX6SOLO;
}
+
+ if (type == MXC_CPU_MX6Q) {
+ if (cfg == 1)
+ type = MXC_CPU_MX6D;
+ }
+
}
reg &= 0xff; /* mx6 silicon revision */
return (type << 12) | (reg + 0x10);
@@ -62,6 +69,9 @@
if (type == MXC_CPU_MX6SOLO)
cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF);
+ if (type == MXC_CPU_MX6D)
+ cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF);
+
return cpurev;
}
#endif
@@ -177,10 +187,41 @@
writew(enable, &wdog2->wmcr);
}
+static void set_ahb_rate(u32 val)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ u32 reg, div;
+
+ div = get_periph_clk() / val - 1;
+ reg = readl(&mxc_ccm->cbcdr);
+
+ writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) |
+ (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr);
+}
+
+static void clear_mmdc_ch_mask(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* Clear MMDC channel mask */
+ writel(0, &mxc_ccm->ccdr);
+}
+
int arch_cpu_init(void)
{
init_aips();
+ /* Need to clear MMDC_CHx_MASK to make warm reset work. */
+ clear_mmdc_ch_mask();
+
+ /*
+ * When low freq boot is enabled, ROM will not set AHB
+ * freq, so we need to ensure AHB freq is 132MHz in such
+ * scenario.
+ */
+ if (mxc_get_clock(MXC_ARM_CLK) == 396000000)
+ set_ahb_rate(132000000);
+
imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */
#ifdef CONFIG_APBH_DMA
@@ -336,3 +377,59 @@
writel(reg, &mxc_ccm->chsccdr);
}
#endif
+
+#ifndef CONFIG_SYS_L2CACHE_OFF
+#define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002
+void v7_outer_cache_enable(void)
+{
+ struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
+ unsigned int val;
+
+#if defined CONFIG_MX6SL
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ val = readl(&iomux->gpr[11]);
+ if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) {
+ /* L2 cache configured as OCRAM, reset it */
+ val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM;
+ writel(val, &iomux->gpr[11]);
+ }
+#endif
+
+ writel(0x132, &pl310->pl310_tag_latency_ctrl);
+ writel(0x132, &pl310->pl310_data_latency_ctrl);
+
+ val = readl(&pl310->pl310_prefetch_ctrl);
+
+ /* Turn on the L2 I/D prefetch */
+ val |= 0x30000000;
+
+ /*
+ * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
+ * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
+ * But according to ARM PL310 errata: 752271
+ * ID: 752271: Double linefill feature can cause data corruption
+ * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
+ * Workaround: The only workaround to this erratum is to disable the
+ * double linefill feature. This is the default behavior.
+ */
+
+#ifndef CONFIG_MX6Q
+ val |= 0x40800000;
+#endif
+ writel(val, &pl310->pl310_prefetch_ctrl);
+
+ val = readl(&pl310->pl310_power_ctrl);
+ val |= L2X0_DYNAMIC_CLK_GATING_EN;
+ val |= L2X0_STNDBY_MODE_EN;
+ writel(val, &pl310->pl310_power_ctrl);
+
+ setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+}
+
+void v7_outer_cache_disable(void)
+{
+ struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
+
+ clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+}
+#endif /* !CONFIG_SYS_L2CACHE_OFF */
diff --git a/arch/arm/cpu/armv7/start.S b/arch/arm/cpu/armv7/start.S
index 6c9b11a..5aac773 100644
--- a/arch/arm/cpu/armv7/start.S
+++ b/arch/arm/cpu/armv7/start.S
@@ -38,12 +38,19 @@
_fiq: .word _fiq
_pad: .word 0x12345678 /* now 16*4=64 */
#else
+.globl _undefined_instruction
_undefined_instruction: .word undefined_instruction
+.globl _software_interrupt
_software_interrupt: .word software_interrupt
+.globl _prefetch_abort
_prefetch_abort: .word prefetch_abort
+.globl _data_abort
_data_abort: .word data_abort
+.globl _not_used
_not_used: .word not_used
+.globl _irq
_irq: .word irq
+.globl _fiq
_fiq: .word fiq
_pad: .word 0x12345678 /* now 16*4=64 */
#endif /* CONFIG_SPL_BUILD */
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index 9231649..a77c4de 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -106,6 +106,8 @@
switch (imxtype) {
case MXC_CPU_MX6Q:
return "6Q"; /* Quad-core version of the mx6 */
+ case MXC_CPU_MX6D:
+ return "6D"; /* Dual-core version of the mx6 */
case MXC_CPU_MX6DL:
return "6DL"; /* Dual Lite version of the mx6 */
case MXC_CPU_MX6SOLO:
diff --git a/arch/arm/include/asm/arch-imx/cpu.h b/arch/arm/include/asm/arch-imx/cpu.h
new file mode 100644
index 0000000..a35940e
--- /dev/null
+++ b/arch/arm/include/asm/arch-imx/cpu.h
@@ -0,0 +1,13 @@
+/*
+ * (C) Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#define MXC_CPU_MX51 0x51
+#define MXC_CPU_MX53 0x53
+#define MXC_CPU_MX6SL 0x60
+#define MXC_CPU_MX6DL 0x61
+#define MXC_CPU_MX6SOLO 0x62
+#define MXC_CPU_MX6Q 0x63
+#define MXC_CPU_MX6D 0x64
diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h
index 9949ad1..ac7705b 100644
--- a/arch/arm/include/asm/arch-mx5/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx5/sys_proto.h
@@ -8,12 +8,7 @@
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
-#define MXC_CPU_MX51 0x51
-#define MXC_CPU_MX53 0x53
-#define MXC_CPU_MX6SL 0x60
-#define MXC_CPU_MX6DL 0x61
-#define MXC_CPU_MX6SOLO 0x62
-#define MXC_CPU_MX6Q 0x63
+#include "../arch-imx/cpu.h"
#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev)
u32 get_cpu_rev(void);
diff --git a/arch/arm/include/asm/arch-mx6/clock.h b/arch/arm/include/asm/arch-mx6/clock.h
index e31ba0a..1b4ded7 100644
--- a/arch/arm/include/asm/arch-mx6/clock.h
+++ b/arch/arm/include/asm/arch-mx6/clock.h
@@ -55,6 +55,7 @@
void enable_ocotp_clk(unsigned char enable);
void enable_usboh3_clk(unsigned char enable);
int enable_sata_clock(void);
+int enable_pcie_clock(void);
int enable_i2c_clk(unsigned char enable, unsigned i2c_num);
void enable_ipu_clock(void);
int enable_fec_anatop_clock(enum enet_freq freq);
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index f2ad6e9..c2d210a 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -53,6 +53,7 @@
#define GLOBAL_TIMER_BASE_ADDR 0x00A00200
#define PRIVATE_TIMERS_WD_BASE_ADDR 0x00A00600
#define IC_DISTRIBUTOR_BASE_ADDR 0x00A01000
+#define L2_PL310_BASE 0x00A02000
#define GPV0_BASE_ADDR 0x00B00000
#define GPV1_BASE_ADDR 0x00C00000
#define PCIE_ARB_BASE_ADDR 0x01000000
diff --git a/arch/arm/include/asm/arch-mx6/iomux.h b/arch/arm/include/asm/arch-mx6/iomux.h
index fe4675e..f9ee0d9 100644
--- a/arch/arm/include/asm/arch-mx6/iomux.h
+++ b/arch/arm/include/asm/arch-mx6/iomux.h
@@ -15,6 +15,33 @@
#define IOMUXC_GPR1_OTG_ID_ENET_RX_ERR (0<<13)
#define IOMUXC_GPR1_OTG_ID_GPIO1 (1<<13)
#define IOMUXC_GPR1_OTG_ID_MASK (1<<13)
+#define IOMUXC_GPR1_REF_SSP_EN (1 << 16)
+#define IOMUXC_GPR1_TEST_POWERDOWN (1 << 18)
+
+/*
+ * IOMUXC_GPR8 bit fields
+ */
+#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_MASK (0x3f << 0)
+#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET 0
+#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_MASK (0x3f << 6)
+#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET 6
+#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_MASK (0x3f << 12)
+#define IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET 12
+#define IOMUXC_GPR8_PCS_TX_SWING_FULL_MASK (0x7f << 18)
+#define IOMUXC_GPR8_PCS_TX_SWING_FULL_OFFSET 18
+#define IOMUXC_GPR8_PCS_TX_SWING_LOW_MASK (0x7f << 25)
+#define IOMUXC_GPR8_PCS_TX_SWING_LOW_OFFSET 25
+
+/*
+ * IOMUXC_GPR12 bit fields
+ */
+#define IOMUXC_GPR12_LOS_LEVEL_9 (0x9 << 4)
+#define IOMUXC_GPR12_LOS_LEVEL_MASK (0x1f << 4)
+#define IOMUXC_GPR12_APPS_LTSSM_ENABLE (1 << 10)
+#define IOMUXC_GPR12_DEVICE_TYPE_EP (0x0 << 12)
+#define IOMUXC_GPR12_DEVICE_TYPE_RC (0x2 << 12)
+#define IOMUXC_GPR12_DEVICE_TYPE_MASK (0xf << 12)
+
/*
* IOMUXC_GPR13 bit fields
*/
diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h
index 17125a6..38851a1 100644
--- a/arch/arm/include/asm/arch-mx6/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx6/sys_proto.h
@@ -9,13 +9,7 @@
#define _SYS_PROTO_H_
#include <asm/imx-common/regs-common.h>
-
-#define MXC_CPU_MX51 0x51
-#define MXC_CPU_MX53 0x53
-#define MXC_CPU_MX6SL 0x60
-#define MXC_CPU_MX6DL 0x61
-#define MXC_CPU_MX6SOLO 0x62
-#define MXC_CPU_MX6Q 0x63
+#include "../arch-imx/cpu.h"
#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev)
u32 get_cpu_rev(void);
diff --git a/arch/arm/include/asm/pl310.h b/arch/arm/include/asm/pl310.h
index f41ad8c..ddc245b 100644
--- a/arch/arm/include/asm/pl310.h
+++ b/arch/arm/include/asm/pl310.h
@@ -12,6 +12,9 @@
/* Register bit fields */
#define PL310_AUX_CTRL_ASSOCIATIVITY_MASK (1 << 16)
+#define L2X0_DYNAMIC_CLK_GATING_EN (1 << 1)
+#define L2X0_STNDBY_MODE_EN (1 << 0)
+#define L2X0_CTRL_EN 1
struct pl310_regs {
u32 pl310_cache_id;
@@ -47,6 +50,24 @@
u32 pad9[1];
u32 pl310_clean_inv_line_idx;
u32 pl310_clean_inv_way;
+ u32 pad10[64];
+ u32 pl310_lockdown_dbase;
+ u32 pl310_lockdown_ibase;
+ u32 pad11[190];
+ u32 pl310_addr_filter_start;
+ u32 pl310_addr_filter_end;
+ u32 pad12[190];
+ u32 pl310_test_operation;
+ u32 pad13[3];
+ u32 pl310_line_data;
+ u32 pad14[7];
+ u32 pl310_line_tag;
+ u32 pad15[3];
+ u32 pl310_debug_ctrl;
+ u32 pad16[7];
+ u32 pl310_prefetch_ctrl;
+ u32 pad17[7];
+ u32 pl310_power_ctrl;
};
void pl310_inval_all(void);
diff --git a/board/boundary/nitrogen6x/README b/board/boundary/nitrogen6x/README
index 5049093..9d84265 100644
--- a/board/boundary/nitrogen6x/README
+++ b/board/boundary/nitrogen6x/README
@@ -67,10 +67,10 @@
To build U-Boot for one of the Nitrogen6x or SabreLite board:
make nitrogen6x_config
- make u-boot.imx
+ make
Note that 'nitrogen6x' is a placeholder. The complete list of supported
-board configurations is shown in tha MAINTAINERS file:
+board configurations is shown in the boards.cfg file:
nitrogen6q i.MX6Q/6D 1GB
nitrogen6dl i.MX6DL 1GB
nitrogen6s i.MX6S 512MB
diff --git a/board/freescale/mx6qsabreauto/imximage.cfg b/board/freescale/mx6qsabreauto/imximage.cfg
index 6d192a6..16bf473 100644
--- a/board/freescale/mx6qsabreauto/imximage.cfg
+++ b/board/freescale/mx6qsabreauto/imximage.cfg
@@ -29,119 +29,101 @@
* Address absolute address of the register
* value value to be stored in the register
*/
+DATA 4 0x020e0798 0x000C0000
+DATA 4 0x020e0758 0x00000000
+DATA 4 0x020e0588 0x00000030
+DATA 4 0x020e0594 0x00000030
+DATA 4 0x020e056c 0x00000030
+DATA 4 0x020e0578 0x00000030
+DATA 4 0x020e074c 0x00000030
+DATA 4 0x020e057c 0x00000030
+DATA 4 0x020e058c 0x00000000
+DATA 4 0x020e059c 0x00000030
+DATA 4 0x020e05a0 0x00000030
+DATA 4 0x020e078c 0x00000030
+DATA 4 0x020e0750 0x00020000
DATA 4 0x020e05a8 0x00000028
DATA 4 0x020e05b0 0x00000028
DATA 4 0x020e0524 0x00000028
DATA 4 0x020e051c 0x00000028
-
DATA 4 0x020e0518 0x00000028
DATA 4 0x020e050c 0x00000028
DATA 4 0x020e05b8 0x00000028
DATA 4 0x020e05c0 0x00000028
-
-DATA 4 0x020e05ac 0x00000028
-DATA 4 0x020e05b4 0x00000028
-DATA 4 0x020e0528 0x00000028
-DATA 4 0x020e0520 0x00000028
-
-DATA 4 0x020e0514 0x00000028
-DATA 4 0x020e0510 0x00000028
-DATA 4 0x020e05bc 0x00000028
-DATA 4 0x020e05c4 0x00000028
-
-DATA 4 0x020e056c 0x00000030
-DATA 4 0x020e0578 0x00000030
-DATA 4 0x020e0588 0x00000030
-DATA 4 0x020e0594 0x00000030
-
-DATA 4 0x020e057c 0x00000030
-DATA 4 0x020e0590 0x00000030
-DATA 4 0x020e0598 0x00000030
-DATA 4 0x020e058c 0x00000000
-
-DATA 4 0x020e059c 0x00003030
-DATA 4 0x020e05a0 0x00003030
+DATA 4 0x020e0774 0x00020000
DATA 4 0x020e0784 0x00000028
DATA 4 0x020e0788 0x00000028
-
DATA 4 0x020e0794 0x00000028
DATA 4 0x020e079c 0x00000028
DATA 4 0x020e07a0 0x00000028
DATA 4 0x020e07a4 0x00000028
-
DATA 4 0x020e07a8 0x00000028
DATA 4 0x020e0748 0x00000028
-DATA 4 0x020e074c 0x00000030
-DATA 4 0x020e0750 0x00020000
-
-DATA 4 0x020e0758 0x00000000
-DATA 4 0x020e0774 0x00020000
-DATA 4 0x020e078c 0x00000030
-DATA 4 0x020e0798 0x000C0000
-
+DATA 4 0x020e05ac 0x00000028
+DATA 4 0x020e05b4 0x00000028
+DATA 4 0x020e0528 0x00000028
+DATA 4 0x020e0520 0x00000028
+DATA 4 0x020e0514 0x00000028
+DATA 4 0x020e0510 0x00000028
+DATA 4 0x020e05bc 0x00000028
+DATA 4 0x020e05c4 0x00000028
+DATA 4 0x021b0800 0xa1390003
+DATA 4 0x021b080c 0x001F001F
+DATA 4 0x021b0810 0x001F001F
+DATA 4 0x021b480c 0x001F001F
+DATA 4 0x021b4810 0x001F001F
+DATA 4 0x021b083c 0x43260335
+DATA 4 0x021b0840 0x031A030B
+DATA 4 0x021b483c 0x4323033B
+DATA 4 0x021b4840 0x0323026F
+DATA 4 0x021b0848 0x483D4545
+DATA 4 0x021b4848 0x44433E48
+DATA 4 0x021b0850 0x41444840
+DATA 4 0x021b4850 0x4835483E
DATA 4 0x021b081c 0x33333333
DATA 4 0x021b0820 0x33333333
DATA 4 0x021b0824 0x33333333
DATA 4 0x021b0828 0x33333333
-
DATA 4 0x021b481c 0x33333333
DATA 4 0x021b4820 0x33333333
DATA 4 0x021b4824 0x33333333
DATA 4 0x021b4828 0x33333333
-
-DATA 4 0x021b0018 0x00001740
-
-DATA 4 0x021b001c 0x00008000
-DATA 4 0x021b000c 0x8A8F7975
-DATA 4 0x021b0010 0xFF538E64
-DATA 4 0x021b0014 0x01FF00DB
-DATA 4 0x021b002c 0x000026D2
-
-DATA 4 0x021b0030 0x008F0E21
-DATA 4 0x021b0008 0x09444040
-DATA 4 0x021b0004 0x00020036
-DATA 4 0x021b0040 0x00000047
-DATA 4 0x021b0000 0x841A0000
-
-DATA 4 0x021b001c 0x04088032
-DATA 4 0x021b001c 0x00008033
-DATA 4 0x021b001c 0x00428031
-DATA 4 0x021b001c 0x09408030
-
-DATA 4 0x021b001c 0x04008040
-DATA 4 0x021b0800 0xA1380003
-DATA 4 0x021b0020 0x00005800
-DATA 4 0x021b0818 0x00000007
-DATA 4 0x021b4818 0x00000007
-
-/* Calibration values based on ARD and 528MHz */
-DATA 4 0x021b083c 0x434B0358
-DATA 4 0x021b0840 0x033D033C
-DATA 4 0x021b483c 0x03520362
-DATA 4 0x021b4840 0x03480318
-DATA 4 0x021b0848 0x41383A3C
-DATA 4 0x021b4848 0x3F3C374A
-DATA 4 0x021b0850 0x42434444
-DATA 4 0x021b4850 0x4932473A
-
-DATA 4 0x021b080c 0x001F001F
-DATA 4 0x021b0810 0x001F001F
-
-DATA 4 0x021b480c 0x001F001F
-DATA 4 0x021b4810 0x001F001F
-
DATA 4 0x021b08b8 0x00000800
DATA 4 0x021b48b8 0x00000800
-
-DATA 4 0x021b0404 0x00011006
+DATA 4 0x021b0004 0x00020036
+DATA 4 0x021b0008 0x09444040
+DATA 4 0x021b000c 0x8A8F7955
+DATA 4 0x021b0010 0xFF328F64
+DATA 4 0x021b0014 0x01FF00DB
+DATA 4 0x021b0018 0x00001740
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x008F1023
+DATA 4 0x021b0040 0x00000047
+DATA 4 0x021b0000 0x841A0000
+DATA 4 0x021b001c 0x04088032
+DATA 4 0x021b001c 0x00008033
+DATA 4 0x021b001c 0x00048031
+DATA 4 0x021b001c 0x09408030
+DATA 4 0x021b001c 0x04008040
+DATA 4 0x021b0020 0x00005800
+DATA 4 0x021b0818 0x00011117
+DATA 4 0x021b4818 0x00011117
DATA 4 0x021b0004 0x00025576
-
+DATA 4 0x021b0404 0x00011006
DATA 4 0x021b001c 0x00000000
+/* set the default clock gate to save power */
DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC00
+DATA 4 0x020c406c 0x0030FC03
DATA 4 0x020c4070 0x0FFFC000
DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
+DATA 4 0x020c4078 0xFFFFF300
+DATA 4 0x020c407c 0x0F0000F3
+DATA 4 0x020c4080 0x00000FFF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4 0x020e0010 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4 0x020e0018 0x007F007F
+DATA 4 0x020e001c 0x007F007F
diff --git a/board/solidrun/hummingboard/hummingboard.c b/board/solidrun/hummingboard/hummingboard.c
index 8b309b4..2e2fb2a 100644
--- a/board/solidrun/hummingboard/hummingboard.c
+++ b/board/solidrun/hummingboard/hummingboard.c
@@ -156,11 +156,7 @@
setup_iomux_enet();
- ret = cpu_eth_init(bis);
- if (ret)
- printf("FEC MXC: %s:failed\n", __func__);
-
- return ret;
+ return cpu_eth_init(bis);
}
#endif
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 3b2b995..4cefda4 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -128,8 +128,12 @@
* Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
* and do not drop the Preamble.
*/
- writel((((imx_get_fecclk() / 1000000) + 2) / 5) << 1,
- ð->mii_speed);
+ register u32 speed = DIV_ROUND_UP(imx_get_fecclk(), 5000000);
+#ifdef FEC_QUIRK_ENET_MAC
+ speed--;
+#endif
+ speed <<= 1;
+ writel(speed, ð->mii_speed);
debug("%s: mii_speed %08x\n", __func__, readl(ð->mii_speed));
}
diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
index 6182a59..18458d3 100644
--- a/drivers/pci/Makefile
+++ b/drivers/pci/Makefile
@@ -10,6 +10,7 @@
obj-$(CONFIG_PCI_INDIRECT_BRIDGE) += pci_indirect.o
obj-$(CONFIG_PCI_GT64120) += pci_gt64120.o
obj-$(CONFIG_PCI_MSC01) += pci_msc01.o
+obj-$(CONFIG_PCIE_IMX) += pcie_imx.o
obj-$(CONFIG_FTPCI100) += pci_ftpci100.o
obj-$(CONFIG_IXP_PCI) += pci_ixp.o
obj-$(CONFIG_SH4_PCI) += pci_sh4.o
diff --git a/drivers/pci/pcie_imx.c b/drivers/pci/pcie_imx.c
new file mode 100644
index 0000000..34377e9
--- /dev/null
+++ b/drivers/pci/pcie_imx.c
@@ -0,0 +1,606 @@
+/*
+ * Freescale i.MX6 PCI Express Root-Complex driver
+ *
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ *
+ * Based on upstream Linux kernel driver:
+ * pci-imx6.c: Sean Cross <xobs@kosagi.com>
+ * pcie-designware.c: Jingoo Han <jg1.han@samsung.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/sizes.h>
+#include <errno.h>
+
+#define PCI_ACCESS_READ 0
+#define PCI_ACCESS_WRITE 1
+
+#define MX6_DBI_ADDR 0x01ffc000
+#define MX6_DBI_SIZE 0x4000
+#define MX6_IO_ADDR 0x01000000
+#define MX6_IO_SIZE 0x100000
+#define MX6_MEM_ADDR 0x01100000
+#define MX6_MEM_SIZE 0xe00000
+#define MX6_ROOT_ADDR 0x01f00000
+#define MX6_ROOT_SIZE 0xfc000
+
+/* PCIe Port Logic registers (memory-mapped) */
+#define PL_OFFSET 0x700
+#define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28)
+#define PCIE_PHY_DEBUG_R1 (PL_OFFSET + 0x2c)
+#define PCIE_PHY_DEBUG_R1_LINK_UP (1 << 4)
+#define PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING (1 << 29)
+
+#define PCIE_PHY_CTRL (PL_OFFSET + 0x114)
+#define PCIE_PHY_CTRL_DATA_LOC 0
+#define PCIE_PHY_CTRL_CAP_ADR_LOC 16
+#define PCIE_PHY_CTRL_CAP_DAT_LOC 17
+#define PCIE_PHY_CTRL_WR_LOC 18
+#define PCIE_PHY_CTRL_RD_LOC 19
+
+#define PCIE_PHY_STAT (PL_OFFSET + 0x110)
+#define PCIE_PHY_STAT_DATA_LOC 0
+#define PCIE_PHY_STAT_ACK_LOC 16
+
+/* PHY registers (not memory-mapped) */
+#define PCIE_PHY_RX_ASIC_OUT 0x100D
+
+#define PHY_RX_OVRD_IN_LO 0x1005
+#define PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5)
+#define PHY_RX_OVRD_IN_LO_RX_PLL_EN (1 << 3)
+
+/* iATU registers */
+#define PCIE_ATU_VIEWPORT 0x900
+#define PCIE_ATU_REGION_INBOUND (0x1 << 31)
+#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31)
+#define PCIE_ATU_REGION_INDEX1 (0x1 << 0)
+#define PCIE_ATU_REGION_INDEX0 (0x0 << 0)
+#define PCIE_ATU_CR1 0x904
+#define PCIE_ATU_TYPE_MEM (0x0 << 0)
+#define PCIE_ATU_TYPE_IO (0x2 << 0)
+#define PCIE_ATU_TYPE_CFG0 (0x4 << 0)
+#define PCIE_ATU_TYPE_CFG1 (0x5 << 0)
+#define PCIE_ATU_CR2 0x908
+#define PCIE_ATU_ENABLE (0x1 << 31)
+#define PCIE_ATU_BAR_MODE_ENABLE (0x1 << 30)
+#define PCIE_ATU_LOWER_BASE 0x90C
+#define PCIE_ATU_UPPER_BASE 0x910
+#define PCIE_ATU_LIMIT 0x914
+#define PCIE_ATU_LOWER_TARGET 0x918
+#define PCIE_ATU_BUS(x) (((x) & 0xff) << 24)
+#define PCIE_ATU_DEV(x) (((x) & 0x1f) << 19)
+#define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16)
+#define PCIE_ATU_UPPER_TARGET 0x91C
+
+/*
+ * PHY access functions
+ */
+static int pcie_phy_poll_ack(void __iomem *dbi_base, int exp_val)
+{
+ u32 val;
+ u32 max_iterations = 10;
+ u32 wait_counter = 0;
+
+ do {
+ val = readl(dbi_base + PCIE_PHY_STAT);
+ val = (val >> PCIE_PHY_STAT_ACK_LOC) & 0x1;
+ wait_counter++;
+
+ if (val == exp_val)
+ return 0;
+
+ udelay(1);
+ } while (wait_counter < max_iterations);
+
+ return -ETIMEDOUT;
+}
+
+static int pcie_phy_wait_ack(void __iomem *dbi_base, int addr)
+{
+ u32 val;
+ int ret;
+
+ val = addr << PCIE_PHY_CTRL_DATA_LOC;
+ writel(val, dbi_base + PCIE_PHY_CTRL);
+
+ val |= (0x1 << PCIE_PHY_CTRL_CAP_ADR_LOC);
+ writel(val, dbi_base + PCIE_PHY_CTRL);
+
+ ret = pcie_phy_poll_ack(dbi_base, 1);
+ if (ret)
+ return ret;
+
+ val = addr << PCIE_PHY_CTRL_DATA_LOC;
+ writel(val, dbi_base + PCIE_PHY_CTRL);
+
+ ret = pcie_phy_poll_ack(dbi_base, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+/* Read from the 16-bit PCIe PHY control registers (not memory-mapped) */
+static int pcie_phy_read(void __iomem *dbi_base, int addr , int *data)
+{
+ u32 val, phy_ctl;
+ int ret;
+
+ ret = pcie_phy_wait_ack(dbi_base, addr);
+ if (ret)
+ return ret;
+
+ /* assert Read signal */
+ phy_ctl = 0x1 << PCIE_PHY_CTRL_RD_LOC;
+ writel(phy_ctl, dbi_base + PCIE_PHY_CTRL);
+
+ ret = pcie_phy_poll_ack(dbi_base, 1);
+ if (ret)
+ return ret;
+
+ val = readl(dbi_base + PCIE_PHY_STAT);
+ *data = val & 0xffff;
+
+ /* deassert Read signal */
+ writel(0x00, dbi_base + PCIE_PHY_CTRL);
+
+ ret = pcie_phy_poll_ack(dbi_base, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int pcie_phy_write(void __iomem *dbi_base, int addr, int data)
+{
+ u32 var;
+ int ret;
+
+ /* write addr */
+ /* cap addr */
+ ret = pcie_phy_wait_ack(dbi_base, addr);
+ if (ret)
+ return ret;
+
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* capture data */
+ var |= (0x1 << PCIE_PHY_CTRL_CAP_DAT_LOC);
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ ret = pcie_phy_poll_ack(dbi_base, 1);
+ if (ret)
+ return ret;
+
+ /* deassert cap data */
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack de-assertion */
+ ret = pcie_phy_poll_ack(dbi_base, 0);
+ if (ret)
+ return ret;
+
+ /* assert wr signal */
+ var = 0x1 << PCIE_PHY_CTRL_WR_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack */
+ ret = pcie_phy_poll_ack(dbi_base, 1);
+ if (ret)
+ return ret;
+
+ /* deassert wr signal */
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack de-assertion */
+ ret = pcie_phy_poll_ack(dbi_base, 0);
+ if (ret)
+ return ret;
+
+ writel(0x0, dbi_base + PCIE_PHY_CTRL);
+
+ return 0;
+}
+
+static int imx6_pcie_link_up(void)
+{
+ u32 rc, ltssm;
+ int rx_valid, temp;
+
+ /* link is debug bit 36, debug register 1 starts at bit 32 */
+ rc = readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R1);
+ if ((rc & PCIE_PHY_DEBUG_R1_LINK_UP) &&
+ !(rc & PCIE_PHY_DEBUG_R1_LINK_IN_TRAINING))
+ return -EAGAIN;
+
+ /*
+ * From L0, initiate MAC entry to gen2 if EP/RC supports gen2.
+ * Wait 2ms (LTSSM timeout is 24ms, PHY lock is ~5us in gen2).
+ * If (MAC/LTSSM.state == Recovery.RcvrLock)
+ * && (PHY/rx_valid==0) then pulse PHY/rx_reset. Transition
+ * to gen2 is stuck
+ */
+ pcie_phy_read((void *)MX6_DBI_ADDR, PCIE_PHY_RX_ASIC_OUT, &rx_valid);
+ ltssm = readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R0) & 0x3F;
+
+ if (rx_valid & 0x01)
+ return 0;
+
+ if (ltssm != 0x0d)
+ return 0;
+
+ printf("transition to gen2 is stuck, reset PHY!\n");
+
+ pcie_phy_read((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, &temp);
+ temp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN | PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+ pcie_phy_write((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, temp);
+
+ udelay(3000);
+
+ pcie_phy_read((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, &temp);
+ temp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN | PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+ pcie_phy_write((void *)MX6_DBI_ADDR, PHY_RX_OVRD_IN_LO, temp);
+
+ return 0;
+}
+
+/*
+ * iATU region setup
+ */
+static int imx_pcie_regions_setup(void)
+{
+ /*
+ * i.MX6 defines 16MB in the AXI address map for PCIe.
+ *
+ * That address space excepted the pcie registers is
+ * split and defined into different regions by iATU,
+ * with sizes and offsets as follows:
+ *
+ * 0x0100_0000 --- 0x010F_FFFF 1MB IORESOURCE_IO
+ * 0x0110_0000 --- 0x01EF_FFFF 14MB IORESOURCE_MEM
+ * 0x01F0_0000 --- 0x01FF_FFFF 1MB Cfg + Registers
+ */
+
+ /* CMD reg:I/O space, MEM space, and Bus Master Enable */
+ setbits_le32(MX6_DBI_ADDR | PCI_COMMAND,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ /* Set the CLASS_REV of RC CFG header to PCI_CLASS_BRIDGE_PCI */
+ setbits_le32(MX6_DBI_ADDR + PCI_CLASS_REVISION,
+ PCI_CLASS_BRIDGE_PCI << 16);
+
+ /* Region #0 is used for Outbound CFG space access. */
+ writel(0, MX6_DBI_ADDR + PCIE_ATU_VIEWPORT);
+
+ writel(MX6_ROOT_ADDR, MX6_DBI_ADDR + PCIE_ATU_LOWER_BASE);
+ writel(0, MX6_DBI_ADDR + PCIE_ATU_UPPER_BASE);
+ writel(MX6_ROOT_ADDR + MX6_ROOT_SIZE, MX6_DBI_ADDR + PCIE_ATU_LIMIT);
+
+ writel(0, MX6_DBI_ADDR + PCIE_ATU_LOWER_TARGET);
+ writel(0, MX6_DBI_ADDR + PCIE_ATU_UPPER_TARGET);
+ writel(PCIE_ATU_TYPE_CFG0, MX6_DBI_ADDR + PCIE_ATU_CR1);
+ writel(PCIE_ATU_ENABLE, MX6_DBI_ADDR + PCIE_ATU_CR2);
+
+ return 0;
+}
+
+/*
+ * PCI Express accessors
+ */
+static uint32_t get_bus_address(pci_dev_t d, int where)
+{
+ uint32_t va_address;
+
+ /* Reconfigure Region #0 */
+ writel(0, MX6_DBI_ADDR + PCIE_ATU_VIEWPORT);
+
+ if (PCI_BUS(d) < 2)
+ writel(PCIE_ATU_TYPE_CFG0, MX6_DBI_ADDR + PCIE_ATU_CR1);
+ else
+ writel(PCIE_ATU_TYPE_CFG1, MX6_DBI_ADDR + PCIE_ATU_CR1);
+
+ if (PCI_BUS(d) == 0) {
+ va_address = MX6_DBI_ADDR;
+ } else {
+ writel(d << 8, MX6_DBI_ADDR + PCIE_ATU_LOWER_TARGET);
+ va_address = MX6_IO_ADDR + SZ_16M - SZ_1M;
+ }
+
+ va_address += (where & ~0x3);
+
+ return va_address;
+}
+
+static int imx_pcie_addr_valid(pci_dev_t d)
+{
+ if ((PCI_BUS(d) == 0) && (PCI_DEV(d) > 1))
+ return -EINVAL;
+ if ((PCI_BUS(d) == 1) && (PCI_DEV(d) > 0))
+ return -EINVAL;
+ return 0;
+}
+
+/*
+ * Replace the original ARM DABT handler with a simple jump-back one.
+ *
+ * The problem here is that if we have a PCIe bridge attached to this PCIe
+ * controller, but no PCIe device is connected to the bridges' downstream
+ * port, the attempt to read/write from/to the config space will produce
+ * a DABT. This is a behavior of the controller and can not be disabled
+ * unfortuatelly.
+ *
+ * To work around the problem, we backup the current DABT handler address
+ * and replace it with our own DABT handler, which only bounces right back
+ * into the code.
+ */
+static void imx_pcie_fix_dabt_handler(bool set)
+{
+ extern uint32_t *_data_abort;
+ uint32_t *data_abort_addr = (uint32_t *)&_data_abort;
+
+ static const uint32_t data_abort_bounce_handler = 0xe25ef004;
+ uint32_t data_abort_bounce_addr = (uint32_t)&data_abort_bounce_handler;
+
+ static uint32_t data_abort_backup;
+
+ if (set) {
+ data_abort_backup = *data_abort_addr;
+ *data_abort_addr = data_abort_bounce_addr;
+ } else {
+ *data_abort_addr = data_abort_backup;
+ }
+}
+
+static int imx_pcie_read_config(struct pci_controller *hose, pci_dev_t d,
+ int where, u32 *val)
+{
+ uint32_t va_address;
+ int ret;
+
+ ret = imx_pcie_addr_valid(d);
+ if (ret) {
+ *val = 0xffffffff;
+ return ret;
+ }
+
+ va_address = get_bus_address(d, where);
+
+ /*
+ * Read the PCIe config space. We must replace the DABT handler
+ * here in case we got data abort from the PCIe controller, see
+ * imx_pcie_fix_dabt_handler() description. Note that writing the
+ * "val" with valid value is also imperative here as in case we
+ * did got DABT, the val would contain random value.
+ */
+ imx_pcie_fix_dabt_handler(true);
+ writel(0xffffffff, val);
+ *val = readl(va_address);
+ imx_pcie_fix_dabt_handler(false);
+
+ return 0;
+}
+
+static int imx_pcie_write_config(struct pci_controller *hose, pci_dev_t d,
+ int where, u32 val)
+{
+ uint32_t va_address = 0;
+ int ret;
+
+ ret = imx_pcie_addr_valid(d);
+ if (ret)
+ return ret;
+
+ va_address = get_bus_address(d, where);
+
+ /*
+ * Write the PCIe config space. We must replace the DABT handler
+ * here in case we got data abort from the PCIe controller, see
+ * imx_pcie_fix_dabt_handler() description.
+ */
+ imx_pcie_fix_dabt_handler(true);
+ writel(val, va_address);
+ imx_pcie_fix_dabt_handler(false);
+
+ return 0;
+}
+
+/*
+ * Initial bus setup
+ */
+static int imx6_pcie_assert_core_reset(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
+ clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+
+ return 0;
+}
+
+static int imx6_pcie_init_phy(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ clrbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_APPS_LTSSM_ENABLE);
+
+ clrsetbits_le32(&iomuxc_regs->gpr[12],
+ IOMUXC_GPR12_DEVICE_TYPE_MASK,
+ IOMUXC_GPR12_DEVICE_TYPE_RC);
+ clrsetbits_le32(&iomuxc_regs->gpr[12],
+ IOMUXC_GPR12_LOS_LEVEL_MASK,
+ IOMUXC_GPR12_LOS_LEVEL_9);
+
+ writel((0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET) |
+ (0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET) |
+ (20 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET) |
+ (127 << IOMUXC_GPR8_PCS_TX_SWING_FULL_OFFSET) |
+ (127 << IOMUXC_GPR8_PCS_TX_SWING_LOW_OFFSET),
+ &iomuxc_regs->gpr[8]);
+
+ return 0;
+}
+
+__weak int imx6_pcie_toggle_reset(void)
+{
+ /*
+ * See 'PCI EXPRESS BASE SPECIFICATION, REV 3.0, SECTION 6.6.1'
+ * for detailed understanding of the PCIe CR reset logic.
+ *
+ * The PCIe #PERST reset line _MUST_ be connected, otherwise your
+ * design does not conform to the specification. You must wait at
+ * least 20 mS after de-asserting the #PERST so the EP device can
+ * do self-initialisation.
+ *
+ * In case your #PERST pin is connected to a plain GPIO pin of the
+ * CPU, you can define CONFIG_PCIE_IMX_PERST_GPIO in your board's
+ * configuration file and the condition below will handle the rest
+ * of the reset toggling.
+ *
+ * In case your #PERST toggling logic is more complex, for example
+ * connected via CPLD or somesuch, you can override this function
+ * in your board file and implement reset logic as needed. You must
+ * not forget to wait at least 20 mS after de-asserting #PERST in
+ * this case either though.
+ *
+ * In case your #PERST line of the PCIe EP device is not connected
+ * at all, your design is broken and you should fix your design,
+ * otherwise you will observe problems like for example the link
+ * not coming up after rebooting the system back from running Linux
+ * that uses the PCIe as well OR the PCIe link might not come up in
+ * Linux at all in the first place since it's in some non-reset
+ * state due to being previously used in U-Boot.
+ */
+#ifdef CONFIG_PCIE_IMX_PERST_GPIO
+ gpio_direction_output(CONFIG_PCIE_IMX_PERST_GPIO, 0);
+ mdelay(20);
+ gpio_set_value(CONFIG_PCIE_IMX_PERST_GPIO, 1);
+ mdelay(20);
+#else
+ puts("WARNING: Make sure the PCIe #PERST line is connected!\n");
+#endif
+ return 0;
+}
+
+static int imx6_pcie_deassert_core_reset(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* FIXME: Power-up GPIO goes here. */
+
+ /* Enable PCIe */
+ clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
+ setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+
+ enable_pcie_clock();
+
+ /*
+ * Wait for the clock to settle a bit, when the clock are sourced
+ * from the CPU, we need about 30mS to settle.
+ */
+ mdelay(50);
+
+ imx6_pcie_toggle_reset();
+
+ return 0;
+}
+
+static int imx_pcie_link_up(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ uint32_t tmp;
+ int count = 0;
+
+ imx6_pcie_assert_core_reset();
+ imx6_pcie_init_phy();
+ imx6_pcie_deassert_core_reset();
+
+ imx_pcie_regions_setup();
+
+ /*
+ * FIXME: Force the PCIe RC to Gen1 operation
+ * The RC must be forced into Gen1 mode before bringing the link
+ * up, otherwise no downstream devices are detected. After the
+ * link is up, a managed Gen1->Gen2 transition can be initiated.
+ */
+ tmp = readl(MX6_DBI_ADDR + 0x7c);
+ tmp &= ~0xf;
+ tmp |= 0x1;
+ writel(tmp, MX6_DBI_ADDR + 0x7c);
+
+ /* LTSSM enable, starting link. */
+ setbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_APPS_LTSSM_ENABLE);
+
+ while (!imx6_pcie_link_up()) {
+ udelay(10);
+ count++;
+ if (count >= 2000) {
+ debug("phy link never came up\n");
+ debug("DEBUG_R0: 0x%08x, DEBUG_R1: 0x%08x\n",
+ readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R0),
+ readl(MX6_DBI_ADDR + PCIE_PHY_DEBUG_R1));
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+void imx_pcie_init(void)
+{
+ /* Static instance of the controller. */
+ static struct pci_controller pcc;
+ struct pci_controller *hose = &pcc;
+ int ret;
+
+ memset(&pcc, 0, sizeof(pcc));
+
+ /* PCI I/O space */
+ pci_set_region(&hose->regions[0],
+ MX6_IO_ADDR, MX6_IO_ADDR,
+ MX6_IO_SIZE, PCI_REGION_IO);
+
+ /* PCI memory space */
+ pci_set_region(&hose->regions[1],
+ MX6_MEM_ADDR, MX6_MEM_ADDR,
+ MX6_MEM_SIZE, PCI_REGION_MEM);
+
+ /* System memory space */
+ pci_set_region(&hose->regions[2],
+ MMDC0_ARB_BASE_ADDR, MMDC0_ARB_BASE_ADDR,
+ 0xefffffff, PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
+
+ hose->region_count = 3;
+
+ pci_set_ops(hose,
+ pci_hose_read_config_byte_via_dword,
+ pci_hose_read_config_word_via_dword,
+ imx_pcie_read_config,
+ pci_hose_write_config_byte_via_dword,
+ pci_hose_write_config_word_via_dword,
+ imx_pcie_write_config);
+
+ /* Start the controller. */
+ ret = imx_pcie_link_up();
+
+ if (!ret) {
+ pci_register_hose(hose);
+ hose->last_busno = pci_hose_scan(hose);
+ }
+}
+
+/* Probe function. */
+void pci_init_board(void)
+{
+ imx_pcie_init();
+}
diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h
index 29a023c..b189bf1 100644
--- a/include/configs/cgtqmx6eval.h
+++ b/include/configs/cgtqmx6eval.h
@@ -75,7 +75,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"boot_dir=/boot\0" \
"console=ttymxc1\0" \
@@ -92,24 +92,24 @@
"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
- "${boot_dir}/${uimage}\0" \
+ "loadimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+ "${boot_dir}/${image}\0" \
"loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdt_addr} " \
"${boot_dir}/${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -118,7 +118,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else "\
"echo ERR: Fail to boot from mmc; " \
diff --git a/include/configs/hummingboard.h b/include/configs/hummingboard.h
index 4055af5..ac65620 100644
--- a/include/configs/hummingboard.h
+++ b/include/configs/hummingboard.h
@@ -92,7 +92,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console=ttymxc0\0" \
"splashpos=m,m\0" \
"fdt_high=0xffffffff\0" \
@@ -124,22 +124,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
@@ -151,19 +151,19 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -171,7 +171,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/m53evk.h b/include/configs/m53evk.h
index a344af4..bd67603 100644
--- a/include/configs/m53evk.h
+++ b/include/configs/m53evk.h
@@ -39,6 +39,8 @@
#define CONFIG_CMD_USB
#define CONFIG_VIDEO
+#define CONFIG_REGEX /* Enable regular expression support */
+
/*
* Memory configurations
*/
@@ -128,9 +130,9 @@
#define CONFIG_LZO
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
-#define MTDIDS_DEFAULT "nand0=mxc-nand"
+#define MTDIDS_DEFAULT "nand0=mxc_nand"
#define MTDPARTS_DEFAULT \
- "mtdparts=mxc-nand:" \
+ "mtdparts=mxc_nand:" \
"1m(bootloader)ro," \
"512k(environment)," \
"512k(redundant-environment)," \
diff --git a/include/configs/mx23evk.h b/include/configs/mx23evk.h
index 1b40a36..b496892 100644
--- a/include/configs/mx23evk.h
+++ b/include/configs/mx23evk.h
@@ -84,7 +84,7 @@
"fi ; " \
"fi\0" \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console=ttyAMA0\0" \
"fdt_file=imx23-evk.dtb\0" \
"fdt_addr=0x41000000\0" \
@@ -98,22 +98,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -121,7 +121,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else " \
"echo ERR: Fail to boot from MMC; " \
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
index 4fd67eb..9b9124a 100644
--- a/include/configs/mx28evk.h
+++ b/include/configs/mx28evk.h
@@ -198,7 +198,7 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"nand write ${loadaddr} kernel ${filesize}\0" \
"update_nand_fdt=" /* Update fdt */ \
"mtdparts default; " \
@@ -230,10 +230,10 @@
"nand read ${loadaddr} kernel 0x00400000; " \
"if test ${boot_fdt} = yes; then " \
"nand read ${fdt_addr} fdt 0x00080000; " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = no; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo \"ERROR: Set boot_fdt to yes or no.\"; " \
"fi; " \
@@ -248,7 +248,7 @@
"fi ; " \
"fi\0" \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console_fsl=ttyAM0\0" \
"console_mainline=ttyAMA0\0" \
"fdt_file=imx28-evk.dtb\0" \
@@ -264,22 +264,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console_mainline},${baudrate} " \
"root=/dev/nfs " \
@@ -291,19 +291,19 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi;" \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -311,7 +311,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h
index 1cff171..b389475 100644
--- a/include/configs/mx51evk.h
+++ b/include/configs/mx51evk.h
@@ -143,7 +143,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"fdt_file=imx51-babbage.dtb\0" \
"fdt_addr=0x91000000\0" \
"boot_fdt=try\0" \
@@ -157,22 +157,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=ttymxc0,${baudrate} " \
"root=/dev/nfs " \
@@ -184,20 +184,20 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo ERROR: Cannot load the DT; " \
"exit; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -205,7 +205,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
index ae43ea3..77f8567 100644
--- a/include/configs/mx53loco.h
+++ b/include/configs/mx53loco.h
@@ -103,7 +103,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"fdt_file=imx53-qsb.dtb\0" \
"fdt_addr=0x71000000\0" \
"boot_fdt=try\0" \
@@ -116,22 +116,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=ttymxc0,${baudrate} " \
"root=/dev/nfs " \
@@ -143,20 +143,20 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo ERROR: Cannot load the DT; " \
"exit; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -164,7 +164,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/mx6_common.h b/include/configs/mx6_common.h
index 514d634..eb107d3 100644
--- a/include/configs/mx6_common.h
+++ b/include/configs/mx6_common.h
@@ -22,4 +22,9 @@
#define CONFIG_ARM_ERRATA_751472
#define CONFIG_BOARD_POSTCLK_INIT
+#ifndef CONFIG_SYS_L2CACHE_OFF
+#define CONFIG_SYS_L2_PL310
+#define CONFIG_SYS_PL310_BASE L2_PL310_BASE
+#endif
+
#endif
diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h
index f0a82d1..fd651cf 100644
--- a/include/configs/mx6qarm2.h
+++ b/include/configs/mx6qarm2.h
@@ -72,7 +72,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console=ttymxc3\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
@@ -85,16 +85,16 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
- "bootm\0" \
+ "bootz\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
- "dhcp ${uimage}; bootm\0" \
+ "dhcp ${image}; bootz\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev};" \
@@ -102,7 +102,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h
index 5ee7fa5..4efcebf 100644
--- a/include/configs/mx6sabre_common.h
+++ b/include/configs/mx6sabre_common.h
@@ -119,7 +119,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_addr=0x18000000\0" \
"boot_fdt=try\0" \
@@ -150,22 +150,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
@@ -177,19 +177,19 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -198,7 +198,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h
index b29f78c..e5bdcc2 100644
--- a/include/configs/mx6slevk.h
+++ b/include/configs/mx6slevk.h
@@ -76,12 +76,12 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console=ttymxc0\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"fdt_file=imx6sl-evk.dtb\0" \
- "fdt_addr=0x81000000\0" \
+ "fdt_addr=0x88000000\0" \
"boot_fdt=try\0" \
"ip_dyn=yes\0" \
"mmcdev=0\0" \
@@ -93,22 +93,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
@@ -120,19 +120,19 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -141,7 +141,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h
index f4ff5cd..e656551 100644
--- a/include/configs/nitrogen6x.h
+++ b/include/configs/nitrogen6x.h
@@ -352,4 +352,15 @@
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_CMD_FS_GENERIC
+/*
+ * PCI express
+ */
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#endif
+
#endif /* __CONFIG_H */
diff --git a/include/configs/udoo.h b/include/configs/udoo.h
index 614e1fe..7f09489 100644
--- a/include/configs/udoo.h
+++ b/include/configs/udoo.h
@@ -100,7 +100,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console=ttymxc1\0" \
"splashpos=m,m\0" \
"fdt_high=0xffffffff\0" \
@@ -132,22 +132,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
@@ -159,19 +159,19 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -179,7 +179,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h
index 8d0a00d..500fd2f 100644
--- a/include/configs/vf610twr.h
+++ b/include/configs/vf610twr.h
@@ -81,7 +81,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
- "uimage=uImage\0" \
+ "image=zImage\0" \
"console=ttyLP1\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
@@ -112,22 +112,22 @@
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
@@ -139,19 +139,19 @@
"else " \
"setenv get_cmd tftp; " \
"fi; " \
- "${get_cmd} ${uimage}; " \
+ "${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
- "bootm; " \
+ "bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
- "bootm; " \
+ "bootz; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
@@ -159,7 +159,7 @@
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
- "if run loaduimage; then " \
+ "if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \