AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master

Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
diff --git a/MAKEALL b/MAKEALL
index 2f4eeb7..dad6bd1 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -450,7 +450,6 @@
 	at91sam9g10ek		\
 	at91sam9g20ek		\
 	at91sam9m10g45ek	\
-	at91sam9rlek		\
 	pm9g45			\
 	SBC35_A9G20		\
 	TNY_A9260		\
diff --git a/Makefile b/Makefile
index e081c25..54b8804 100644
--- a/Makefile
+++ b/Makefile
@@ -844,18 +844,6 @@
 	fi;
 	@$(MKCONFIG) -n $@ -a at91sam9263ek arm arm926ejs at91sam9263ek atmel at91
 
-at91sam9rlek_nandflash_config \
-at91sam9rlek_dataflash_config \
-at91sam9rlek_dataflash_cs0_config \
-at91sam9rlek_config	:	unconfig
-	@mkdir -p $(obj)include
-	@if [ "$(findstring _nandflash,$@)" ] ; then \
-		echo "#define CONFIG_SYS_USE_NANDFLASH 1"	>>$(obj)include/config.h ; \
-	else \
-		echo "#define CONFIG_SYS_USE_DATAFLASH 1"	>>$(obj)include/config.h ; \
-	fi;
-	@$(MKCONFIG) -n $@ -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91
-
 at91sam9m10g45ek_nandflash_config \
 at91sam9m10g45ek_dataflash_config \
 at91sam9m10g45ek_dataflash_cs0_config \
diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c
index e374917..e559084 100644
--- a/board/atmel/at91sam9rlek/at91sam9rlek.c
+++ b/board/atmel/at91sam9rlek/at91sam9rlek.c
@@ -23,6 +23,7 @@
  */
 
 #include <common.h>
+#include <asm/io.h>
 #include <asm/arch/at91sam9rl.h>
 #include <asm/arch/at91sam9rl_matrix.h>
 #include <asm/arch/at91sam9_smc.h>
@@ -31,7 +32,7 @@
 #include <asm/arch/at91_rstc.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/gpio.h>
-#include <asm/arch/io.h>
+
 #include <lcd.h>
 #include <atmel_lcdc.h>
 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
@@ -48,33 +49,37 @@
 #ifdef CONFIG_CMD_NAND
 static void at91sam9rlek_nand_hw_init(void)
 {
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
 	unsigned long csa;
 
 	/* Enable CS3 */
-	csa = at91_sys_read(AT91_MATRIX_EBICSA);
-	at91_sys_write(AT91_MATRIX_EBICSA,
-		       csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+	csa = readl(&matrix->ebicsa);
+	csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
+
+	writel(csa, &matrix->ebicsa);
 
 	/* Configure SMC CS3 for NAND/SmartMedia */
-	at91_sys_write(AT91_SMC_SETUP(3),
-		       AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
-		       AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-	at91_sys_write(AT91_SMC_PULSE(3),
-		       AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
-		       AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-	at91_sys_write(AT91_SMC_CYCLE(3),
-		       AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-	at91_sys_write(AT91_SMC_MODE(3),
-		       AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
-		       AT91_SMC_EXNWMODE_DISABLE |
+	writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+		AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+		&smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
+		AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
+		&smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
+		&smc->cs[3].cycle);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+		AT91_SMC_MODE_EXNW_DISABLE |
 #ifdef CONFIG_SYS_NAND_DBW_16
-		       AT91_SMC_DBW_16 |
+		AT91_SMC_MODE_DBW_16 |
 #else /* CONFIG_SYS_NAND_DBW_8 */
-		       AT91_SMC_DBW_8 |
+		AT91_SMC_MODE_DBW_8 |
 #endif
-		       AT91_SMC_TDF_(2));
+		AT91_SMC_MODE_TDF_CYCLE(2),
+		&smc->cs[3].mode);
 
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_PIOD);
+	writel(1 << ATMEL_ID_PIOD, &pmc->pcer);
 
 	/* Configure RDY/BSY */
 	at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
@@ -102,7 +107,7 @@
 	vl_vsync_len:	1,
 	vl_upper_margin:1,
 	vl_lower_margin:0,
-	mmio:		AT91SAM9RL_LCDC_BASE,
+	mmio:		ATMEL_BASE_LCDC,
 };
 
 void lcd_enable(void)
@@ -116,6 +121,8 @@
 }
 static void at91sam9rlek_lcd_hw_init(void)
 {
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
 	at91_set_B_periph(AT91_PIN_PC1, 0);	/* LCDPWR */
 	at91_set_A_periph(AT91_PIN_PC5, 0);	/* LCDHSYNC */
 	at91_set_A_periph(AT91_PIN_PC6, 0);	/* LCDDOTCK */
@@ -138,9 +145,7 @@
 	at91_set_B_periph(AT91_PIN_PC24, 0);	/* LCDD22 */
 	at91_set_B_periph(AT91_PIN_PC25, 0);	/* LCDD23 */
 
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_LCDC);
-
-	gd->fb_base = 0;
+	writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
 }
 
 #ifdef CONFIG_LCD_INFO
@@ -157,7 +162,7 @@
 	lcd_printf ("(C) 2008 ATMEL Corp\n");
 	lcd_printf ("at91support@atmel.com\n");
 	lcd_printf ("%s CPU at %s MHz\n",
-		CONFIG_SYS_AT91_CPU_NAME,
+		ATMEL_CPU_NAME,
 		strmhz(temp, get_cpu_clk_rate()));
 
 	dram_size = 0;
@@ -173,6 +178,17 @@
 #endif /* CONFIG_LCD_INFO */
 #endif
 
+int board_early_init_f(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+	/* Enable clocks for all PIOs */
+	writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
+		(1 << ATMEL_ID_PIOC) | (1 << ATMEL_ID_PIOD),
+		&pmc->pcer);
+
+	return 0;
+}
 
 int board_init(void)
 {
@@ -182,9 +198,9 @@
 	/* arch number of AT91SAM9RLEK-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK;
 	/* adress of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-	at91_serial_hw_init();
+	at91_seriald_hw_init();
 #ifdef CONFIG_CMD_NAND
 	at91sam9rlek_nand_hw_init();
 #endif
@@ -199,7 +215,8 @@
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	gd->ram_size = get_ram_size(
+		(void *)CONFIG_SYS_SDRAM_BASE,
+		CONFIG_SYS_SDRAM_SIZE);
 	return 0;
 }
diff --git a/board/atmel/at91sam9rlek/config.mk b/board/atmel/at91sam9rlek/config.mk
deleted file mode 100644
index e554a45..0000000
--- a/board/atmel/at91sam9rlek/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x23f00000
diff --git a/board/atmel/at91sam9rlek/led.c b/board/atmel/at91sam9rlek/led.c
index 9634cc0..987e8c0 100644
--- a/board/atmel/at91sam9rlek/led.c
+++ b/board/atmel/at91sam9rlek/led.c
@@ -26,12 +26,14 @@
 #include <asm/arch/at91sam9rl.h>
 #include <asm/arch/at91_pmc.h>
 #include <asm/arch/gpio.h>
-#include <asm/arch/io.h>
+#include <asm/io.h>
 
 void coloured_LED_init(void)
 {
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
 	/* Enable clock */
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_PIOD);
+	writel(ATMEL_ID_PIOD, &pmc->pcer);
 
 	at91_set_gpio_output(CONFIG_RED_LED, 1);
 	at91_set_gpio_output(CONFIG_GREEN_LED, 1);
diff --git a/boards.cfg b/boards.cfg
index 3e79c82..8a5a618 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -80,6 +80,8 @@
 at91sam9g20ek_nandflash      arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH
 at91sam9g20ek_dataflash_cs0  arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0
 at91sam9g20ek_dataflash_cs1  arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1
+at91sam9rlek_nandflash       arm         arm926ejs   at91sam9rlek        atmel          at91        at91sam9rlek:AT91SAM9RL,SYS_USE_NANDFLASH
+at91sam9rlek_dataflash       arm         arm926ejs   at91sam9rlek        atmel          at91        at91sam9rlek:AT91SAM9RL,SYS_USE_DATAFLASH
 at91sam9xeek_nandflash       arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_NANDFLASH
 at91sam9xeek_dataflash_cs0   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS0
 at91sam9xeek_dataflash_cs1   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1
diff --git a/include/configs/at91sam9rlek.h b/include/configs/at91sam9rlek.h
index 8dbd082..3ca09e1 100644
--- a/include/configs/at91sam9rlek.h
+++ b/include/configs/at91sam9rlek.h
@@ -27,33 +27,42 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_AT91_LEGACY
+#include <asm/hardware.h>
+
+#define CONFIG_SYS_TEXT_BASE		0x21F00000
 
 /* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000	/* 12 MHz crystal */
-#define CONFIG_SYS_HZ		1000
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000	/* main clock xtal */
+#define CONFIG_SYS_HZ			1000
 
-#define CONFIG_ARM926EJS	1	/* This is an ARM926EJS Core	*/
-#define CONFIG_AT91SAM9RL	1	/* It's an Atmel AT91SAM9RL SoC*/
-#define CONFIG_AT91SAM9RLEK	1	/* on an AT91SAM9RLEK Board	*/
+#define CONFIG_AT91SAM9RLEK		1	/* It's an AT91SAM9RLEK Board */
+
 #define CONFIG_ARCH_CPU_INIT
-#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff	*/
-
-#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs	*/
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG	1
-
 #define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
+
+#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS	1
+#define CONFIG_INITRD_TAG		1
+
+#define CONFIG_DISPLAY_CPUINFO
+
+#define CONFIG_ATMEL_LEGACY
+#define CONFIG_AT91_GPIO		1
+#define CONFIG_AT91_GPIO_PULLUP		1
 
 /*
  * Hardware drivers
  */
-#define CONFIG_AT91_GPIO	1
-#define CONFIG_ATMEL_USART	1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3		1	/* USART 3 is DBGU */
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define CONFIG_USART_ID			ATMEL_ID_SYS
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200, 19200, 38400, 57600, 9600}
 
 /* LCD */
 #define CONFIG_LCD			1
@@ -62,10 +71,13 @@
 #undef LCD_TEST_PATTERN
 #define CONFIG_LCD_INFO			1
 #define CONFIG_LCD_INFO_BELOW_LOGO	1
-#define CONFIG_SYS_WHITE_ON_BLACK		1
+#define CONFIG_SYS_WHITE_ON_BLACK	1
 #define CONFIG_ATMEL_LCD		1
 #define CONFIG_ATMEL_LCD_RGB565		1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV		1
+/* Let board_init_f handle the framebuffer allocation */
+#undef CONFIG_FB_ADDR
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+
 
 /* LED */
 #define CONFIG_AT91_LED
@@ -85,25 +97,29 @@
 #undef CONFIG_CMD_IMLS
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
 #undef CONFIG_CMD_SOURCE
 #undef CONFIG_CMD_USB
 
-#define CONFIG_CMD_NAND		1
+#define CONFIG_CMD_NAND			1
 
 /* SDRAM */
 #define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM			0x20000000
-#define PHYS_SDRAM_SIZE			0x04000000	/* 64 megs */
+#define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
+#define CONFIG_SYS_SDRAM_SIZE		0x04000000
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE)
 
 /* DataFlash */
 #define CONFIG_ATMEL_DATAFLASH_SPI
-#define CONFIG_HAS_DATAFLASH		1
+#define CONFIG_HAS_DATAFLASH			1
 #define CONFIG_SYS_SPI_WRITE_TOUT		(5*CONFIG_SYS_HZ)
 #define CONFIG_SYS_MAX_DATAFLASH_BANKS		1
 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0	0xC0000000	/* CS0 */
-#define AT91_SPI_CLK			15000000
-#define DATAFLASH_TCSS			(0x1a << 16)
-#define DATAFLASH_TCHS			(0x1 << 24)
+#define AT91_SPI_CLK				15000000
+#define DATAFLASH_TCSS				(0x1a << 16)
+#define DATAFLASH_TCHS				(0x1 << 24)
 
 /* NOR flash - not present */
 #define CONFIG_SYS_NO_FLASH			1
@@ -112,7 +128,7 @@
 #ifdef CONFIG_CMD_NAND
 #define CONFIG_NAND_ATMEL
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
-#define CONFIG_SYS_NAND_BASE			0x40000000
+#define CONFIG_SYS_NAND_BASE			ATMEL_BASE_CS3
 #define CONFIG_SYS_NAND_DBW_8			1
 /* our ALE is AD21 */
 #define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
@@ -129,7 +145,7 @@
 
 #define CONFIG_SYS_LOAD_ADDR			0x22000000	/* load address */
 
-#define CONFIG_SYS_MEMTEST_START		PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_START		CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END			0x23e00000
 
 #ifdef CONFIG_SYS_USE_DATAFLASH
@@ -149,7 +165,7 @@
 #else /* CONFIG_SYS_USE_NANDFLASH */
 
 /* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_IS_IN_NAND	1
+#define CONFIG_ENV_IS_IN_NAND		1
 #define CONFIG_ENV_OFFSET		0x60000
 #define CONFIG_ENV_OFFSET_REDUND	0x80000
 #define CONFIG_ENV_SIZE		0x20000		/* 1 sector = 128 kB */
@@ -161,25 +177,20 @@
 
 #endif
 
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }
-
 #define CONFIG_SYS_PROMPT		"U-Boot> "
 #define CONFIG_SYS_CBSIZE		256
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING	1
+#define CONFIG_CMDLINE_EDITING		1
 
 /*
  * Size of malloc() pool
  */
-#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+#define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
 
 #define CONFIG_STACKSIZE	(32*1024)	/* regular stack */
 
-#ifdef CONFIG_USE_IRQ
-#error CONFIG_USE_IRQ not supported
-#endif
+#undef CONFIG_USE_IRQ
 
 #endif