omap730p2: Remove board
Signed-off-by: Tom Rini <trini@ti.com>
diff --git a/board/ti/omap730p2/Makefile b/board/ti/omap730p2/Makefile
deleted file mode 100644
index 8242f3d..0000000
--- a/board/ti/omap730p2/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := omap730p2.o flash.o
-obj-y += lowlevel_init.o
diff --git a/board/ti/omap730p2/README.omap730p2 b/board/ti/omap730p2/README.omap730p2
deleted file mode 100644
index 7c70916..0000000
--- a/board/ti/omap730p2/README.omap730p2
+++ /dev/null
@@ -1,91 +0,0 @@
-
- u-boot for the TI OMAP730 Perseus2
-
- Dave Peverley, MPC-Data Limited
- http://www.mpc-data.co.uk
-
-
-Overview :
-
- As the OMAP730 is similar to the OMAP1610 in many ways, this port was based
-on the u-boot port to the OMAP1610 Innovator. Supported features are :
-
- - Serial terminal support
- - Onboard NOR Flash
- - Ethernet via the seperate debug board
- - Tested on Rev4 and Rev5 boards
-
- It has also been tested to work correctly when built with a 'standard' GCC
-3.2.1 cross-compiler as well as Montavista Linux CEE 3.1's toolchain.
-
-
-Hardware Configuration :
-
- The main dips on the P2 board should be set to 2,3,7 and 9 on with all
-others off. On the debug board, dips 1 and 7 should be on with the rest off.
-The serial console has been set up to run from the DB9 connector on the
-P2 board at 115200 baud, 8 data bits, no stop bits, 1 parity bit.
-
- It should be noted that the P2 board has NOR flash that is addressable via
-either CS0 or CS3. This mode can be changed via DIP9 on the P2 board.
-
-
-Installing u-boot for the P2 :
-
- You can simply build u-boot for the Perseus by following the instructions
-in the main readme file. The target configuration is "omap730p2_config".
-Once u-boot has been built, you should strip the executable so it can be
-loaded via CCS (which cant cope with the symbols in the ELF binary) :
- $ cp u-boot u-boot.out
- $ arm-linux-strip u-boot.out
-
- The method we've used for installing u-boot the first time on a P2 is
-as follows :
-
-1) Configure TI Code Composer Studio to connect to the P2 board via JTAG
- as described in the Users Guide.
-
-2) Set up the P2 to boot from CS3, and connect with CCS. Reset the CPU
- and run the "init_mmu" GEL script.
-
-3) Use the "Load Program" option to send the u-boot.out file to the P2 and
- run.
-
- At this point, u-boot should run and you will see the boot menu on your
-serial terminal. You can then load the u-boot image to memory :
-
- # loadb 0x10000000
-
- Send the "u-boot.bin" binary via the serial using Kermit. Once loaded
-you can self-flash u-boot :
-
- # protect off 1:0
- # erase 1:0
- # cp.b 0x10000000 0x0 0x20000
-
- You should now be able to reset the board and run u-boot from flash.
-
-
-Alternative flash option :
-
- Sometimes, if you've been silly, you can get the board into a state where
-whats in flash has upset the board so much that you can no longer connect
-to the P2 via JTAG. However, you can set DIP9 to off to swap the boot mode
-of the P2 so that you boot from RAM instead of NOR flash. This moves NOR
-flash up to 0x0C000000. You can build a special version of u-boot to
-utilise this by the following config :
-
- $ make omap730p2_cs0boot_config
-
- If you load this up via CCS it will detect flash at its alternate location
-and allow you to programme your u-boot image (which, remember must be built
-for CS3 boot!) Once you do this, you can revert to CS3 boot and it will work
-fine again.
-
-
-Errata :
-
-1) It's been observed that sometimes the tftp transfer of kernels to the
- board can have checksum errors or stall. This appears to be an issue
- with the lan91c96.c driver, and can normally be worked around by
- resetting the board and trying again.
diff --git a/board/ti/omap730p2/config.mk b/board/ti/omap730p2/config.mk
deleted file mode 100644
index 8618820..0000000
--- a/board/ti/omap730p2/config.mk
+++ /dev/null
@@ -1,25 +0,0 @@
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# TI Perseus 2 board with OMAP720 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Innovator has 1 bank of 256 MB SDRAM
-# Physical Address:
-# 1000'0000 to 2000'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# we load ourself to 1108'0000
-#
-#
-
-CONFIG_SYS_TEXT_BASE = 0x11080000
diff --git a/board/ti/omap730p2/flash.c b/board/ti/omap730p2/flash.c
deleted file mode 100644
index 56f981c..0000000
--- a/board/ti/omap730p2/flash.c
+++ /dev/null
@@ -1,463 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH ushort
-#define FLASH_PORT_WIDTHV vu_short
-#define SWAP(x) __swab16(x)
-#else
-#define FLASH_PORT_WIDTH ulong
-#define FLASH_PORT_WIDTHV vu_long
-#define SWAP(x) __swab32(x)
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-
-/* Flash Organization Structure */
-typedef struct OrgDef {
- unsigned int sector_number;
- unsigned int sector_size;
-} OrgDef;
-
-
-/* Flash Organizations */
-OrgDef OrgIntel_28F256L18T[] = {
- {4, 32 * 1024}, /* 4 * 32kBytes sectors */
- {255, 128 * 1024}, /* 255 * 128kBytes sectors */
-};
-
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-unsigned long flash_init (void);
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-void flash_print_info (flash_info_t * info);
-void flash_unprotect_sectors (FPWV * addr);
-int flash_erase (flash_info_t * info, int s_first, int s_last);
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i;
- ulong size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- switch (i) {
- case 0:
- flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
- flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
- break;
- default:
- panic ("configured too many flash banks!\n");
- break;
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
-
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- if (i > 255) {
- info->start[i] = base + (i * 0x8000);
- info->protect[i] = 0;
- } else {
- info->start[i] = base +
- (i * PHYS_FLASH_SECT_SIZE);
- info->protect[i] = 0;
- }
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F256L18T:
- printf ("FLASH 28F256L18T\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
- volatile FPW value;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = (FPW) 0x00AA00AA;
- addr[0x2AAA] = (FPW) 0x00550055;
- addr[0x5555] = (FPW) 0x00900090;
-
- mb ();
- value = addr[0];
-
- switch (value) {
-
- case (FPW) INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- mb ();
- value = addr[1]; /* device ID */
- switch (value) {
-
- case (FPW) (INTEL_ID_28F256L18T):
- info->flash_id += FLASH_28F256L18T;
- info->sector_count = 259;
- info->size = 0x02000000;
- break; /* => 32 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/* unprotects a sector for write and erase
- * on some intel parts, this unprotects the entire chip, but it
- * wont hurt to call this additional times per sector...
- */
-void flash_unprotect_sectors (FPWV * addr)
-{
-#define PD_FINTEL_WSMS_READY_MASK 0x0080
-
- *addr = (FPW) 0x00500050; /* clear status register */
-
- /* this sends the clear lock bit command */
- *addr = (FPW) 0x00600060;
- *addr = (FPW) 0x00D000D0;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong type, start;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- FPWV *addr = (FPWV *) (info->start[sect]);
- FPW status;
-
- printf ("Erasing sector %2d ... ", sect);
-
- flash_unprotect_sectors (addr);
-
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0);
-
- *addr = (FPW) 0x00500050;/* clear status register */
- *addr = (FPW) 0x00200020;/* erase setup */
- *addr = (FPW) 0x00D000D0;/* erase confirm */
-
- while (((status =
- *addr) & (FPW) 0x00800080) !=
- (FPW) 0x00800080) {
- if (get_timer(start) >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- /* suspend erase */
- *addr = (FPW) 0x00B000B0;
- /* reset to read mode */
- *addr = (FPW) 0x00FF00FF;
- rcode = 1;
- break;
- }
- }
-
- /* clear status register cmd. */
- *addr = (FPW) 0x00500050;
- *addr = (FPW) 0x00FF00FF;/* resest to read mode */
- printf (" done\n");
- }
- }
-
- if (flag)
- enable_interrupts();
-
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- FPW data;
- int count, i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
- wp = (addr & ~1);
- port_width = 2;
-#else
- wp = (addr & ~3);
- port_width = 4;
-#endif
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- count = 0;
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- if (count++ > 0x800) {
- spin_wheel ();
- count = 0;
- }
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
- FPWV *addr = (FPWV *) dest;
- ulong status;
- int flag, rc = 0;
- ulong start;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
- return (2);
- }
- flash_unprotect_sectors (addr);
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
- *addr = (FPW) 0x00400040; /* write setup */
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- start = get_timer(0);
-
- /* wait while polling the status register */
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- rc = 1;
- goto done;
- }
- }
-done:
- *addr = (FPW)0x00FF00FF; /* restore read mode */
- if (flag)
- enable_interrupts();
- return rc;
-}
-
-void inline spin_wheel (void)
-{
- static int p = 0;
- static char w[] = "\\/-";
-
- printf ("\010%c", w[p]);
- (++p == 3) ? (p = 0) : 0;
-}
diff --git a/board/ti/omap730p2/lowlevel_init.S b/board/ti/omap730p2/lowlevel_init.S
deleted file mode 100644
index 795c495..0000000
--- a/board/ti/omap730p2/lowlevel_init.S
+++ /dev/null
@@ -1,379 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003-2004
- *
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited
- * (http://www.mpc-data.co.uk)
- *
- * TODO : Tidy up and change to use system register defines
- * from omap730.h where possible.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
-_TEXT_BASE:
- .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */
-
-.globl lowlevel_init
-lowlevel_init:
- /* Save callers address in r11 - r11 must never be modified */
- mov r11, lr
-
- /*------------------------------------------------------*
- *mask all IRQs by setting all bits in the INTMR default*
- *------------------------------------------------------*/
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT1) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT1
- ldr r1, VAL_ARM_IDLECT1
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT2) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT2
- ldr r1, VAL_ARM_IDLECT2
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT3) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT3
- ldr r1, VAL_ARM_IDLECT3
- str r1, [r0]
-
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- /* I supposedly need to enable the dsp clock before switching */
- mov r1, #0x1000
- ldr r0, REG_ARM_SYSST
- strh r1, [r0]
- mov r0, #0x400
-1:
- subs r0, r0, #0x1 /* wait for any bubbles to finish */
- bne 1b
- ldr r1, VAL_ARM_CKCTL
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* a few nops to let settle */
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* setup DPLL 1 */
- /* Ramp up the clock to 96Mhz */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit.*/
- beq 2b /* loop until bit goes hi. */
-lock_end:
-
- /*------------------------------------------------------*
- * Turn off the watchdog during init... *
- *------------------------------------------------------*/
- ldr r0, REG_WATCHDOG
- ldr r1, WATCHDOG_VAL1
- str r1, [r0]
- ldr r1, WATCHDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL1
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-
-watch1Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch1Wait
-
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-watch2Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch2Wait
-
- /* Set memory timings corresponding to the new clock speed */
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- /* Compare physical SDRAM base & current execution location. */
- and r0, pc, #0xF0000000
- /* Compare. */
- cmp r0, #0
- /* Skip over EMIF-fast initialization if running from SDRAM. */
- bne skip_sdram
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r3, #0x1800 /* value should be checked */
-3:
- subs r3, r3, #0x1 /* Decrement count */
- bne 3b
-
- ldr r0, REG_SDRAM_CONFIG
- ldr r1, SDRAM_CONFIG_VAL
- str r1, [r0]
-
- ldr r0, REG_SDRAM_MRS_LEGACY
- ldr r1, SDRAM_MRS_VAL
- str r1, [r0]
-
-skip_sdram:
-
-common_tc:
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
-
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
- ldr r1, VAL_TC_EMIFS_CS2_CONFIG
- ldr r0, REG_TC_EMIFS_CS2_CONFIG
- str r1, [r0] /* Chip Select 2 */
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
- /* 48MHz clock request for UART1 */
- ldr r1, PERSEUS2_CONFIG_BASE
- ldrh r0, [r1, #CONFIG_PCC_CONF]
- orr r0, r0, #CONF_MOD_UART1_CLK_MODE_R
- strh r0, [r1, #CONFIG_PCC_CONF]
-
- /* Initialize public and private rheas
- * - set access factor 2 on both rhea / strobe
- * - disable write buffer on strb0, enable write buffer on strb1
- */
-
- ldr R0, REG_RHEA_PUB_CTL
- ldr R1, REG_RHEA_PRIV_CTL
- ldr R2, VAL_RHEA_CTL
- strh R2, [R0]
- strh R2, [R1]
- mov R3, #2 /* disable write buffer on strb0, enable write buffer on strb1 */
- strh R3, [R0, #0x08] /* arm rhea control reg */
- strh R3, [R1, #0x08]
-
- /* enable IRQ and FIQ */
-
- mrs r4, CPSR
- bic r4, r4, #IRQ_MASK
- bic r4, r4, #FIQ_MASK
- msr CPSR, r4
-
- /* set TAP CONF to TRI EMULATION */
-
- ldr r1, [r0, #CONFIG_MODE2]
- bic r1, r1, #0x18
- orr r1, r1, #0x10
- str r1, [r0, #CONFIG_MODE2]
-
- /* set tdbgen to 1 */
-
- ldr r0, PERSEUS2_CONFIG_BASE
- ldr r1, [r0, #CONFIG_MODE1]
- mov r2, #0x10000
- orr r1, r1, r2
- str r1, [r0, #CONFIG_MODE1]
-
-#ifdef CONFIG_P2_OMAP1610
- /* inserting additional 2 clock cycle hold time for LAN */
- ldr r0, REG_TC_EMIFS_CS1_ADVANCED
- ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
- str r1, [r0]
-#endif
- /* Start MPU Timer 1 */
- ldr r0, REG_MPU_LOAD_TIMER
- ldr r1, VAL_MPU_LOAD_TIMER
- str r1, [r0]
-
- ldr r0, REG_MPU_CNTL_TIMER
- ldr r1, VAL_MPU_CNTL_TIMER
- str r1, [r0]
-
- /* back to arch calling code */
- mov pc, r11
-
- /* the literal pools origin */
- .ltorg
-
-REG_TC_EMIFS_CONFIG: /* 32 bits */
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-
-#ifdef CONFIG_P2_OMAP730
-REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
- .word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-
-REG_ARM_IDLECT3: /* 16 bits */
- .word 0xfffece24
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_IDLECT1: /* 16 bits */
- .word 0xfffece04
-
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
- .word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
- .word 0xfffeb034
-
-WSPRDOG_VAL1:
- .word 0x0000aaaa
-WSPRDOG_VAL2:
- .word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
- .word 0xfffecc20
-
-REG_SDRAM_MRS_LEGACY:
- .word 0xfffecc24
-
-REG_WATCHDOG:
- .word 0xfffec808
-
-REG_MPU_LOAD_TIMER:
- .word 0xfffec504
-REG_MPU_CNTL_TIMER:
- .word 0xfffec500
-
-/* Public and private rhea bridge registers definition */
-
-REG_RHEA_PUB_CTL:
- .word 0xFFFECA00
-
-REG_RHEA_PRIV_CTL:
- .word 0xFFFED300
-
-/* EMIFF SDRAM Configuration register
- - self refresh disable
- - auto refresh enabled
- - SDRAM type 64 Mb, 16 bits bus 4 banks
- - power down enabled
- - SDRAM clock disabled
- */
-SDRAM_CONFIG_VAL:
- .word 0x0C017DF4
-
-/* Burst full page length ; cas latency = 3 */
-SDRAM_MRS_VAL:
- .word 0x00000037
-
-VAL_ARM_CKCTL:
- .word 0x6505
-VAL_DPLL1_CTL:
- .word 0x3412
-
-#ifdef CONFIG_P2_OMAP730
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x0000FFF3
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x00004278
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x00004278
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x00004278
-VAL_TC_EMIFS_CS1_ADVANCED:
- .word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
- .word 0x00000400
-VAL_ARM_IDLECT2:
- .word 0x00000886
-VAL_ARM_IDLECT3:
- .word 0x00000015
-
-WATCHDOG_VAL1:
- .word 0x000000f5
-WATCHDOG_VAL2:
- .word 0x000000a0
-
-VAL_MPU_LOAD_TIMER:
- .word 0xffffffff
-VAL_MPU_CNTL_TIMER:
- .word 0xffffffa1
-
-VAL_RHEA_CTL:
- .word 0xFF22
-
-/* Config Register vals */
-PERSEUS2_CONFIG_BASE:
- .word 0xFFFE1000
-
-.equ CONFIG_PCC_CONF, 0xB4
-.equ CONFIG_MODE1, 0x10
-.equ CONFIG_MODE2, 0x14
-.equ CONF_MOD_UART1_CLK_MODE_R, 0x0A
-
-/* misc values */
-.equ IRQ_MASK, 0x80 /* IRQ mask value */
-.equ FIQ_MASK, 0x40 /* FIQ mask value */
diff --git a/board/ti/omap730p2/omap730p2.c b/board/ti/omap730p2/omap730p2.c
deleted file mode 100644
index 554019c..0000000
--- a/board/ti/omap730p2/omap730p2.c
+++ /dev/null
@@ -1,255 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#if defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int test_boot_mode(void);
-void spin_up_leds(void);
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define FLASH_ON_CS0 1
-#define FLASH_ON_CS3 0
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-int test_boot_mode(void)
-{
- /* Check for CS0 and CS3 address decode swapping */
- if (*((volatile int *)EMIFS_CONFIG) & 0x00000002)
- return(FLASH_ON_CS3);
- else
- return(FLASH_ON_CS0);
-}
-
-/* Toggle backup LED indication */
-void toggle_backup_led(void)
-{
- static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */
- volatile unsigned int *IOConfReg;
-
-
- IOConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT);
-
- if (backupLEDState != 0) {
- *IOConfReg &= (0xFFFFEFFF);
- backupLEDState = 0;
- } else {
- *IOConfReg |= (0x00001000);
- backupLEDState = 1;
- }
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- /* arch number of OMAP 730 P2 Board - Same as the Innovator! */
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
- /* Configure MUX settings */
- set_muxconf_regs ();
-
- peripheral_power_enable ();
-
- /* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */
- toggle_backup_led();
-
- /* Hold GSM in reset until needed */
- *((volatile unsigned short *)M_CTL) &= ~1;
-
- /*
- * CSx timings, GPIO Mux ... setup
- */
-
- /* Flash: CS0 timings setup */
- *((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3;
- *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088;
-
- /* Ethernet support trough the debug board */
- /* CS1 timings setup */
- *((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3;
- *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000;
-
- /* this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-
- flash__init ();
- ether__init ();
-
- return 0;
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
- unsigned int regval;
-
- regval = *((volatile unsigned int *) EMIFS_CONFIG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_CONFIG) = regval;
-}
-
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define LAN_RESET_REGISTER 0x0400001c
-
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
- do {
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
- udelay (100);
- } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
-
- do {
- *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
- udelay (100);
- } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
-
-#define ETH_CONTROL_REG 0x0400030b
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (100);
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init (void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return 0;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
- specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
- volatile unsigned int *MuxConfReg;
- /* set each registers to its reset value; */
-
- /*
- * Backup LED Indication
- */
-
- /* Configure MUXed pin. Mode 6: GPIO_140 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10);
- *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */
- *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */
-
- /* Configure GPIO_140 as output */
- MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL);
- *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */
-
- /*
- * Configure GPIOs for battery charge & feedback
- */
-
- /* Configure MUXed pin. Mode 6: GPIO_35 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
- *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */
- *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */
-
- /* Configure MUXed pin. Mode 6: GPIO_72,73,74 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5);
- *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */
- *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */
-
- MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL);
- *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */
- *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */
-
- /*
- * Allow battery charge
- */
-
- MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT);
- *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */
-
- /*
- * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
- * It is used as the Ethernet controller interrupt
- */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF9);
- *MuxConfReg &= 0x1FFFFFFF;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
- volatile unsigned int *MuxConfReg;
-
-
- /* Set up pins used by UART */
-
- /* Start UART clock (48MHz) */
- MuxConfReg = (volatile unsigned int *) (PERSEUS_PCC_CONF_REG);
- *MuxConfReg &= (0xFFFFFFF7);
- *MuxConfReg |= (0x00000008);
-
- /* Get the UART pin in mode0 */
- MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
- *MuxConfReg &= (0xFF1FFFFF);
- *MuxConfReg &= (0xF1FFFFFF);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_LAN91C96
- rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
- return rc;
-}
-#endif
diff --git a/boards.cfg b/boards.cfg
index efecbc2..36f0924 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -213,9 +213,6 @@
Active arm arm926ejs nomadik st nhk8815 nhk8815 - Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com>:Alessandro Rubini <rubini@unipv.it>
Active arm arm926ejs nomadik st nhk8815 nhk8815_onenand nhk8815:BOOT_ONENAND Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com>:Alessandro Rubini <rubini@unipv.it>
Active arm arm926ejs omap ti - omap5912osk - Rishi Bhattacharya <rishi@ti.com>
-Active arm arm926ejs omap ti omap730p2 omap730p2 omap730p2:CS3_BOOT Dave Peverley <dpeverley@mpc-data.co.uk>
-Active arm arm926ejs omap ti omap730p2 omap730p2_cs0boot omap730p2:CS0_BOOT Dave Peverley <dpeverley@mpc-data.co.uk>
-Active arm arm926ejs omap ti omap730p2 omap730p2_cs3boot omap730p2:CS3_BOOT Dave Peverley <dpeverley@mpc-data.co.uk>
Active arm arm926ejs orion5x LaCie - edminiv2 - Albert ARIBAUD <albert.u.boot@aribaud.net>
Active arm arm926ejs pantheon Marvell - dkb - Lei Wen <leiwen@marvell.com>
Active arm arm926ejs spear spear - x600 x600 Stefan Roese <sr@denx.de>
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 8ed09c7..a48ce7c 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,8 +11,9 @@
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-pdnb3 arm ixp - 2013-09-24 Stefan Roese <sr@denx.de>
-scpu arm ixp - 2013-09-24 Stefan Roese <sr@denx.de>
+omap730p2 arm arm926ejs - 2013-11-11
+pdnb3 arm ixp 304db0b 2013-09-24 Stefan Roese <sr@denx.de>
+scpu arm ixp 304db0b 2013-09-24 Stefan Roese <sr@denx.de>
omap1510inn arm arm925t 0610a16 2013-09-23 Kshitij Gupta <kshitij@ti.com>
CANBT powerpc 405CR fb8f4fd 2013-08-07 Matthias Fuchs <matthias.fuchs@esd.eu>
Alaska8220 powerpc mpc8220 d6ed322 2013-05-11
diff --git a/include/configs/h2_p2_dbg_board.h b/include/configs/h2_p2_dbg_board.h
deleted file mode 100644
index 4ba2c55..0000000
--- a/include/configs/h2_p2_dbg_board.h
+++ /dev/null
@@ -1,120 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * TI H2 and P2 Debug Board hardware map
- *
- * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk)
- * Author: MPC-Data Limited
- * Dave Peverley
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __INCLUDED_H2_P2_DBH_BOARD_H
-#define __INCLUDED_H2_P2_DBH_BOARD_H
-
-#include <asm/sizes.h>
-
-/*
- * The Debug board is designed to function with the P2 Sample, H2
- * Sample and 1610 Innovator boards. The main difference AFAICT is
- * the chip selects used with each system ;
- *
- * P2 Sample : CS1 of OMAP730 is used to select the CPLD & LAN regs
- * H2 Sample : CS1a is used to select the CPLD registers.
- *
- */
-
-/***************************************************************************
- * CPLD Registers
- **************************************************************************/
-
-#define H2DBG_CPLD_REVISION 0x04000010
-#define H2DBG_BOARD_REVISION 0x04000012
-#define H2DBG_GPIO_REGISTER 0x04000014
-#define H2DBG_LED_CONTROL 0x04000016
-#define H2DBG_MISC_INPUT 0x04000018
-#define H2DBG_LAN_STATUS 0x0400001A
-#define H2DBG_LAN_RESET 0x0400001C
-#define H2DBG_ETH_REG_BASE 0x04000300
-
-/***************************************************************************
- * Ethernet Control Registers
- * These are for the LAN91C96 on the debug board
- **************************************************************************/
-
-/* Bank 0 in IO space */
-
-#define ETH_TCR (H2DBG_ETH_REG_BASE + 0x00) /* Transmit Control Register */
-#define ETH_EPH_STATUS (H2DBG_ETH_REG_BASE + 0x02) /* EPH Status Register */
-#define ETH_RCR (H2DBG_ETH_REG_BASE + 0x04) /* Receive Control Register */
-#define ETH_COUNTER (H2DBG_ETH_REG_BASE + 0x06) /* Counter Register */
-#define ETH_MIR (H2DBG_ETH_REG_BASE + 0x08) /* Memory Information Register */
-#define ETH_MCR (H2DBG_ETH_REG_BASE + 0x0A) /* Memory Configuration Register */
-
-/* Bank 1 in IO space */
-
-#define ETH_CONFIG (H2DBG_ETH_REG_BASE + 0x00) /* Configuration Register */
-#define ETH_BASE (H2DBG_ETH_REG_BASE + 0x02) /* Base Address Register */
-#define ETH_IA0 (H2DBG_ETH_REG_BASE + 0x04) /* Individual Address Register - 0 */
-#define ETH_IA1 (H2DBG_ETH_REG_BASE + 0x05) /* Individual Address Register - 1 */
-#define ETH_IA2 (H2DBG_ETH_REG_BASE + 0x06) /* Individual Address Register - 2 */
-#define ETH_IA3 (H2DBG_ETH_REG_BASE + 0x07) /* Individual Address Register - 3 */
-#define ETH_IA4 (H2DBG_ETH_REG_BASE + 0x08) /* Individual Address Register - 4 */
-#define ETH_IA5 (H2DBG_ETH_REG_BASE + 0x09) /* Individual Address Register - 5 */
-#define ETH_GEN_PURPOSE (H2DBG_ETH_REG_BASE + 0x0A) /* General Address Registers */
-#define ETH_CONTROL (H2DBG_ETH_REG_BASE + 0x0B) /* Control Register */
-
-/* Bank 2 in IO space */
-
-#define ETH_MMU (H2DBG_ETH_REG_BASE + 0x00) /* MMU Command Register */
-#define ETH_AUTO_TX_START (H2DBG_ETH_REG_BASE + 0x01) /* Auto Tx Start Register */
-#define ETH_PNR (H2DBG_ETH_REG_BASE + 0x02) /* Packet Number Register */
-#define ETH_ARR (H2DBG_ETH_REG_BASE + 0x03) /* Allocation Result Register */
-#define ETH_FIFO (H2DBG_ETH_REG_BASE + 0x04) /* FIFO Ports Register */
-#define ETH_POINTER (H2DBG_ETH_REG_BASE + 0x06) /* Pointer Register */
-#define ETH_DATA_HIGH (H2DBG_ETH_REG_BASE + 0x08) /* Data High Register */
-#define ETH_DATA_LOW (H2DBG_ETH_REG_BASE + 0x0A) /* Data Low Register */
-#define ETH_INT_STATS (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Status Register - RO */
-#define ETH_INT_ACK (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Acknowledge Register -WO */
-#define ETH_INT_MASK (H2DBG_ETH_REG_BASE + 0x0D) /* Interrupt Mask Register */
-
-
-#ifndef __ASSEMBLY__
-
-/*
- * A couple of utility inlines to aid debugging using the LED's on the
- * debug board.
- */
-
-static inline void set_led_state(int state)
-{
- static unsigned long hw_led_state = 0;
- volatile unsigned short *led_address = (volatile unsigned short *)0x04000016;
-
- hw_led_state = ((unsigned long)state);
- *((unsigned short *) (led_address)) = (unsigned short) (~hw_led_state & 0xFFFF);
-}
-
-
-static inline void spin_up_leds(void)
-{
- volatile int i, j, k;
-
- for (k = 0; k < 2; k++) {
- for (i = 0; i < 16; i++) {
- for (j = 0; j < 5000; j++) {
- set_led_state(1 << i);
- }
- }
- for (i = 15; i >= 0; i--) {
- for (j = 0; j < 5000; j++) {
- set_led_state(1 << i);
- }
- }
- }
-}
-
-#endif /* ! __ASSEMBLY__ */
-
-#endif /* ! __INCLUDED_H2_P2_DBH_BOARD_H */
diff --git a/include/configs/omap730.h b/include/configs/omap730.h
deleted file mode 100644
index b54e0fb..0000000
--- a/include/configs/omap730.h
+++ /dev/null
@@ -1,246 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * OMAP730 hardware map
- *
- * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk)
- * Author: MPC-Data Limited
- * Dave Peverley
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __INCLUDED_OMAP730_H
-#define __INCLUDED_OMAP730_H
-
-#include <asm/sizes.h>
-
-/***************************************************************************
- * OMAP730 Configuration Registers
- **************************************************************************/
-
-#define PERSEUS2_MPU_DEV_ID ((unsigned int)(0xFFFE1000))
-#define PERSEUS2_GSM_DEV_ID0 ((unsigned int)(0xFFFE1000))
-#define PERSEUS2_GDM_DEV_ID1 ((unsigned int)(0xFFFE1002))
-#define DSP_CONF ((unsigned int)(0xFFFE1004))
-#define PERSEUS2_MPU_DIE_ID0 ((unsigned int)(0xFFFE1008))
-#define GSM_ASIC_CONF ((unsigned int)(0xFFFE1008))
-#define PERSEUS2_MPU_DIE_ID1 ((unsigned int)(0xFFFE100C))
-#define PERSEUS2_MODE1 ((unsigned int)(0xFFFE1010))
-#define PERSEUS2_GSM_DIE_ID0 ((unsigned int)(0xFFFE1010))
-#define PERSEUS2_GSM_DIE_ID1 ((unsigned int)(0xFFFE1012))
-#define PERSEUS2_MODE2 ((unsigned int)(0xFFFE1014))
-#define PERSEUS2_GSM_DIE_ID2 ((unsigned int)(0xFFFE1014))
-#define PERSEUS2_GSM_DIE_ID3 ((unsigned int)(0xFFFE1016))
-#define PERSEUS2_ANALOG_CELLS_CONF ((unsigned int)(0xFFFE1018))
-#define SPECCTL ((unsigned int)(0xFFFE101C))
-#define SPARE1 ((unsigned int)(0xFFFE1020))
-#define SPARE2 ((unsigned int)(0xFFFE1024))
-#define GSM_PBG_IRQ ((unsigned int)(0xFFFE1028))
-#define DMA_REQ_CONF ((unsigned int)(0xFFFE1030))
-#define PE_CONF_NO_DUAL ((unsigned int)(0xFFFE1060))
-#define PERSEUS2_IO_CONF0 ((unsigned int)(0xFFFE1070))
-#define PERSEUS2_IO_CONF1 ((unsigned int)(0xFFFE1074))
-#define PERSEUS2_IO_CONF2 ((unsigned int)(0xFFFE1078))
-#define PERSEUS2_IO_CONF3 ((unsigned int)(0xFFFE107C))
-#define PERSEUS2_IO_CONF4 ((unsigned int)(0xFFFE1080))
-#define PERSEUS2_IO_CONF5 ((unsigned int)(0xFFFE1084))
-#define PERSEUS2_IO_CONF6 ((unsigned int)(0xFFFE1088))
-#define PERSEUS2_IO_CONF7 ((unsigned int)(0xFFFE108C))
-#define PERSEUS2_IO_CONF8 ((unsigned int)(0xFFFE1090))
-#define PERSEUS2_IO_CONF9 ((unsigned int)(0xFFFE1094))
-#define PERSEUS2_IO_CONF10 ((unsigned int)(0xFFFE1098))
-#define PERSEUS2_IO_CONF11 ((unsigned int)(0xFFFE109C))
-#define PERSEUS2_IO_CONF12 ((unsigned int)(0xFFFE10A0))
-#define PERSEUS2_IO_CONF13 ((unsigned int)(0xFFFE10A4))
-#define PERSEUS_PCC_CONF_REG ((unsigned int)(0xFFFE10B4))
-#define BIST_STATUS_INTERNAL ((unsigned int)(0xFFFE10B8))
-#define BIST_CONTROL ((unsigned int)(0xFFFE10C0))
-#define BOOT_ROM_REG ((unsigned int)(0xFFFE10C4))
-#define PRODUCTION_ID_REG ((unsigned int)(0xFFFE10C8))
-#define BIST_SECROM_SIGNATURE1_INTERNAL ((unsigned int)(0xFFFE10D0))
-#define BIST_SECROM_SIGNATURE2_INTERNAL ((unsigned int)(0xFFFE10D4))
-#define BIST_CONTROL_2 ((unsigned int)(0xFFFE10D8))
-#define DEBUG1 ((unsigned int)(0xFFFE10E0))
-#define DEBUG2 ((unsigned int)(0xFFFE10E4))
-#define DEBUG_DMA_IRQ ((unsigned int)(0xFFFE10E8))
-
-/***************************************************************************
- * OMAP730 EMIFS Registers (TRM 2.5.7)
- **************************************************************************/
-
-#define TCMIF_BASE 0xFFFECC00
-
-#define EMIFS_LRUREG (TCMIF_BASE + 0x04)
-#define EMIFS_CONFIG (TCMIF_BASE + 0x0C)
-#define FLASH_CFG_0 (TCMIF_BASE + 0x10)
-#define FLASH_CFG_1 (TCMIF_BASE + 0x14)
-#define FLASH_CFG_2 (TCMIF_BASE + 0x18)
-#define FLASH_CFG_3 (TCMIF_BASE + 0x1C)
-#define FL_CFG_DYN_WAIT (TCMIF_BASE + 0x40)
-#define EMIFS_TIMEOUT1_REG (TCMIF_BASE + 0x28)
-#define EMIFS_TIMEOUT2_REG (TCMIF_BASE + 0x2C)
-#define EMIFS_TIMEOUT3_REG (TCMIF_BASE + 0x30)
-#define EMIFS_ABORT_ADDR (TCMIF_BASE + 0x44)
-#define EMIFS_ABORT_TYPE (TCMIF_BASE + 0x48)
-#define EMIFS_ABORT_TOUT (TCMIF_BASE + 0x4C)
-#define FLASH_ACFG_0_1 (TCMIF_BASE + 0x50)
-#define FLASH_ACFG_1_1 (TCMIF_BASE + 0x54)
-#define FLASH_ACFG_2_1 (TCMIF_BASE + 0x58)
-#define FLASH_ACFG_3_1 (TCMIF_BASE + 0x5C)
-
-/***************************************************************************
- * OMAP730 Interrupt handlers
- **************************************************************************/
-
-#define OMAP_IH1_BASE 0xFFFECB00 /* MPU Level 1 IRQ handler */
-#define OMAP_IH2_BASE 0xfffe0000
-
-/***************************************************************************
- * OMAP730 Timers
- *
- * There are three general purpose OS timers in the 730 that can be
- * configured in autoreload or one-shot modes.
- **************************************************************************/
-
-#define OMAP730_32kHz_TIMER_BASE 0xFFFB9000
-
-/* 32k Timer Registers */
-#define TIMER32k_CR 0x08
-#define TIMER32k_TVR 0x00
-#define TIMER32k_TCR 0x04
-
-/* 32k Timer Control Register definition */
-#define TIMER32k_TSS (1<<0)
-#define TIMER32k_TRB (1<<1)
-#define TIMER32k_INT (1<<2)
-#define TIMER32k_ARL (1<<3)
-
-/* MPU Timer base addresses */
-#define OMAP730_MPUTIMER_BASE 0xfffec500
-#define OMAP730_MPUTIMER_OFF 0x00000100
-
-#define OMAP730_TIMER1_BASE 0xFFFEC500
-#define OMAP730_TIMER2_BASE 0xFFFEC600
-#define OMAP730_TIMER3_BASE 0xFFFEC700
-
-/* MPU Timer Register offsets */
-#define CNTL_TIMER 0x00 /* MPU_CNTL_TIMER */
-#define LOAD_TIM 0x04 /* MPU_LOAD_TIMER */
-#define READ_TIM 0x08 /* MPU_READ_TIMER */
-
-/* MPU_CNTL_TIMER register bits */
-#define MPUTIM_FREE (1<<6)
-#define MPUTIM_CLOCK_ENABLE (1<<5)
-#define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT)
-#define MPUTIM_PTV_BIT 2
-#define MPUTIM_AR (1<<1)
-#define MPUTIM_ST (1<<0)
-
-/***************************************************************************
- * OMAP730 GPIO
- *
- * The GPIO control is split over 6 register bases in the OMAP730 to allow
- * access to all the (6 x 32) GPIO pins!
- **************************************************************************/
-
-#define OMAP730_GPIO_BASE_1 0xFFFBC000
-#define OMAP730_GPIO_BASE_2 0xFFFBC800
-#define OMAP730_GPIO_BASE_3 0xFFFBD000
-#define OMAP730_GPIO_BASE_4 0xFFFBD800
-#define OMAP730_GPIO_BASE_5 0xFFFBE000
-#define OMAP730_GPIO_BASE_6 0xFFFBE800
-
-#define GPIO_DATA_INPUT 0x00
-#define GPIO_DATA_OUTPUT 0x04
-#define GPIO_DIRECTION_CONTROL 0x08
-#define GPIO_INTERRUPT_CONTROL 0x0C
-#define GPIO_INTERRUPT_MASK 0x10
-#define GPIO_INTERRUPT_STATUS 0x14
-
-#define GPIO_DATA_INPUT_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_DATA_INPUT))
-#define GPIO_DATA_OUTPUT_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_DATA_OUTPUT))
-#define GPIO_DIRECTION_CONTROL_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_DIRECTION_CONTROL))
-#define GPIO_INTERRUPT_CONTROL_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_INTERRUPT_CONTROL))
-#define GPIO_INTERRUPT_MASK_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_INTERRUPT_MASK))
-#define GPIO_INTERRUPT_STATUS_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_INTERRUPT_STATUS))
-
-#define GPIO_DATA_INPUT_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_DATA_INPUT))
-#define GPIO_DATA_OUTPUT_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_DATA_OUTPUT))
-#define GPIO_DIRECTION_CONTROL_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_DIRECTION_CONTROL))
-#define GPIO_INTERRUPT_CONTROL_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_INTERRUPT_CONTROL))
-#define GPIO_INTERRUPT_MASK_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_INTERRUPT_MASK))
-#define GPIO_INTERRUPT_STATUS_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_INTERRUPT_STATUS))
-
-#define GPIO_DATA_INPUT_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_DATA_INPUT))
-#define GPIO_DATA_OUTPUT_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT))
-#define GPIO_DIRECTION_CONTROL_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL))
-#define GPIO_INTERRUPT_CONTROL_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_INTERRUPT_CONTROL))
-#define GPIO_INTERRUPT_MASK_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_INTERRUPT_MASK))
-#define GPIO_INTERRUPT_STATUS_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_INTERRUPT_STATUS))
-
-#define GPIO_DATA_INPUT_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_DATA_INPUT))
-#define GPIO_DATA_OUTPUT_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_DATA_OUTPUT))
-#define GPIO_DIRECTION_CONTROL_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_DIRECTION_CONTROL))
-#define GPIO_INTERRUPT_CONTROL_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_INTERRUPT_CONTROL))
-#define GPIO_INTERRUPT_MASK_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_INTERRUPT_MASK))
-#define GPIO_INTERRUPT_STATUS_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_INTERRUPT_STATUS))
-
-#define GPIO_DATA_INPUT_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_DATA_INPUT))
-#define GPIO_DATA_OUTPUT_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT))
-#define GPIO_DIRECTION_CONTROL_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL))
-#define GPIO_INTERRUPT_CONTROL_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_INTERRUPT_CONTROL))
-#define GPIO_INTERRUPT_MASK_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_INTERRUPT_MASK))
-#define GPIO_INTERRUPT_STATUS_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_INTERRUPT_STATUS))
-
-#define GPIO_DATA_INPUT_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_DATA_INPUT))
-#define GPIO_DATA_OUTPUT_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_DATA_OUTPUT))
-#define GPIO_DIRECTION_CONTROL_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_DIRECTION_CONTROL))
-#define GPIO_INTERRUPT_CONTROL_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_INTERRUPT_CONTROL))
-#define GPIO_INTERRUPT_MASK_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_INTERRUPT_MASK))
-#define GPIO_INTERRUPT_STATUS_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_INTERRUPT_STATUS))
-
-/***************************************************************************
- * OMAP730 Watchdog timers
- **************************************************************************/
-
-#define WDTIM_BASE 0xFFFEC800
-#define WDTIM_CONTROL (WDTIM_BASE + 0x00) /* MPU_CNTL_TIMER */
-#define WDTIM_LOAD (WDTIM_BASE + 0x04) /* MPU_LOAD_TIMER */
-#define WDTIM_READ (WDTIM_BASE + 0x04) /* MPU_READ_TIMER */
-#define WDTIM_MODE (WDTIM_BASE + 0x08) /* MPU_TIMER_MODE */
-
-/***************************************************************************
- * OMAP730 Interrupt Registers
- **************************************************************************/
-
-/* Interrupt Register offsets */
-
-#define IRQ_ITR 0x00
-#define IRQ_MIR 0x04
-#define IRQ_SIR_IRQ 0x10
-#define IRQ_SIR_FIQ 0x14
-#define IRQ_CONTROL_REG 0x18
-#define IRQ_ILR0 0x1C /* ILRx == ILR0 + (0x4 * x) */
-#define IRQ_SIR 0x9C /* a.k.a.IRQ_ISR */
-#define IRQ_GMIR 0xA0
-
-#define REG_IHL1_MIR (OMAP_IH1_BASE + IRQ_MIR)
-#define REG_IHL2_MIR (OMAP_IH2_BASE + IRQ_MIR)
-
-/***************************************************************************
- * OMAP730 Intersystem Communication Register (TRM 4.5)
- **************************************************************************/
-
-#define ICR_BASE 0xFFFBB800
-
-#define M_ICR (ICR_BASE + 0x00)
-#define G_ICR (ICR_BASE + 0x02)
-#define M_CTL (ICR_BASE + 0x04)
-#define G_CTL (ICR_BASE + 0x06)
-#define PM_BA (ICR_BASE + 0x0A)
-#define DM_BA (ICR_BASE + 0x0C)
-#define RM_BA (ICR_BASE + 0x0E)
-#define SSPI_TAS (ICR_BASE + 0x12)
-
-#endif /* ! __INCLUDED_OMAP730_H */
diff --git a/include/configs/omap730p2.h b/include/configs/omap730p2.h
deleted file mode 100644
index 947f27b..0000000
--- a/include/configs/omap730p2.h
+++ /dev/null
@@ -1,173 +0,0 @@
-/*
- * (C) Copyright 2003-2004
- * MPC Data Limited (http://www.mpc-data.co.uk)
- * Dave Peverley <dpeverley at mpc-data.co.uk>
- *
- * Configuation settings for the TI OMAP Perseus 2 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_ARM926EJS 1 /* This is an arm926ejs CPU core */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP730 1 /* which is in a 730 */
-#define CONFIG_P2_OMAP730 1 /* a Perseus 2 Board */
-
-/*
- * Input clock of PLL
- * The OMAP730 Perseus 2 has 13MHz input clock
- */
-
-#define CONFIG_SYS_CLK_FREQ 13000000
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-
-/*
- * Size of malloc() pool
- */
-
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-
-#define CONFIG_LAN91C96
-#define CONFIG_LAN91C96_BASE 0x04000300
-#define CONFIG_LAN91C96_EXT_PHY
-
-/*
- * NS16550 Configuration
- */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (1)
-#define CONFIG_SYS_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */
-#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart
- * on perseus */
-
-/*
- * select serial console configuration
- */
-
-#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP730 Perseus 2 */
-
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-
-
-#include <configs/omap730.h>
-#include <configs/h2_p2_dbg_board.h>
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw ip=bootp"
-
-#define CONFIG_LOADADDR 0x10000000
-
-#define CONFIG_ETHADDR
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.0.23
-#define CONFIG_SERVERIP 192.150.0.100
-#define CONFIG_BOOTFILE "uImage" /* File to load */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 115200 /* Speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 1 /* Which serial port to use */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "OMAP730 P2 # " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
-
-/* The OMAP730 has 3 general purpose MPU timers, they can be driven by
- * the RefClk (12Mhz) or by DPLL1. This time is further subdivided by a
- * local divisor.
- */
-#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
-
-#if defined(CONFIG_CS0_BOOT)
-#define PHYS_FLASH_1 0x0C000000
-#elif defined(CONFIG_CS3_BOOT)
-#define PHYS_FLASH_1 0x00000000
-#else
-#error Unknown Boot Chip-Select number
-#endif
-
-#define PHYS_SRAM 0x20000000
-
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */
-#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
-/* addr of environment */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x020000)
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_OFFSET 0x20000 /* environment starts here */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR PHYS_SRAM
-
-#endif /* ! __CONFIG_H */