Merge branch 'master' of git://git.denx.de/u-boot
diff --git a/README b/README
index 3547ead..676f41e 100644
--- a/README
+++ b/README
@@ -4422,6 +4422,9 @@
If defined, specified the chip address of the EEPROM device.
The default address is zero.
+ - CONFIG_SYS_I2C_EEPROM_BUS:
+ If defined, specified the i2c bus of the EEPROM device.
+
- CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
If defined, the number of bits used to address bytes in a
single page in the EEPROM device. A 64 byte page, for example
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index bc55e5b..8472d41 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -465,6 +465,10 @@
bool "Support wandboard"
select CPU_V7
+config TARGET_WARP
+ bool "Support WaRP"
+ select CPU_V7
+
config TARGET_TITANIUM
bool "Support titanium"
select CPU_V7
@@ -842,6 +846,7 @@
source "board/udoo/Kconfig"
source "board/vpac270/Kconfig"
source "board/wandboard/Kconfig"
+source "board/warp/Kconfig"
source "board/woodburn/Kconfig"
source "board/xaeniax/Kconfig"
source "board/xilinx/zynqmp/Kconfig"
diff --git a/arch/arm/cpu/arm1136/mx31/Makefile b/arch/arm/cpu/arm1136/mx31/Makefile
index 9670ed9..dcbd570 100644
--- a/arch/arm/cpu/arm1136/mx31/Makefile
+++ b/arch/arm/cpu/arm1136/mx31/Makefile
@@ -8,3 +8,7 @@
obj-y += generic.o
obj-y += timer.o
obj-y += devices.o
+
+ifndef CONFIG_SPL_BUILD
+obj-y += relocate.o
+endif
diff --git a/arch/arm/cpu/arm1136/mx31/relocate.S b/arch/arm/cpu/arm1136/mx31/relocate.S
new file mode 100644
index 0000000..1c556df
--- /dev/null
+++ b/arch/arm/cpu/arm1136/mx31/relocate.S
@@ -0,0 +1,23 @@
+/*
+ * relocate - i.MX31-specific vector relocation
+ *
+ * Copyright (c) 2013 Albert ARIBAUD <albert.u.boot@aribaud.net>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/linkage.h>
+
+/*
+ * The i.MX31 SoC is very specific with respect to exceptions: it
+ * does not provide RAM at the high vectors address (0xFFFF0000),
+ * thus only the low address (0x00000000) is useable; but that is
+ * in ROM, so let's avoid relocating the vectors.
+ */
+ .section .text.relocate_vectors,"ax",%progbits
+
+ENTRY(relocate_vectors)
+
+ bx lr
+
+ENDPROC(relocate_vectors)
diff --git a/arch/arm/cpu/arm1136/mx35/Makefile b/arch/arm/cpu/arm1136/mx35/Makefile
index c533215..796db9c 100644
--- a/arch/arm/cpu/arm1136/mx35/Makefile
+++ b/arch/arm/cpu/arm1136/mx35/Makefile
@@ -10,3 +10,7 @@
obj-y += generic.o
obj-y += timer.o
obj-y += mx35_sdram.o
+
+ifndef CONFIG_SPL_BUILD
+obj-y += relocate.o
+endif
diff --git a/arch/arm/cpu/arm1136/mx35/relocate.S b/arch/arm/cpu/arm1136/mx35/relocate.S
new file mode 100644
index 0000000..43003f8
--- /dev/null
+++ b/arch/arm/cpu/arm1136/mx35/relocate.S
@@ -0,0 +1,23 @@
+/*
+ * relocate - i.MX35-specific vector relocation
+ *
+ * Copyright (c) 2013 Albert ARIBAUD <albert.u.boot@aribaud.net>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/linkage.h>
+
+/*
+ * The i.MX35 SoC is very specific with respect to exceptions: it
+ * does not provide RAM at the high vectors address (0xFFFF0000),
+ * thus only the low address (0x00000000) is useable; but that is
+ * in ROM, so let's avoid relocating the vectors.
+ */
+ .section .text.relocate_vectors,"ax",%progbits
+
+ENTRY(relocate_vectors)
+
+ bx lr
+
+ENDPROC(relocate_vectors)
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index e599a12..ef02972 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -230,6 +230,11 @@
struct wdog_regs *wdog1 = (struct wdog_regs *)WDOG1_BASE_ADDR;
struct wdog_regs *wdog2 = (struct wdog_regs *)WDOG2_BASE_ADDR;
+#ifdef CONFIG_MX6SX
+ struct wdog_regs *wdog3 = (struct wdog_regs *)WDOG3_BASE_ADDR;
+ writew(enable, &wdog3->wmcr);
+#endif
+
/* Write to the PDE (Power Down Enable) bit */
writew(enable, &wdog1->wmcr);
writew(enable, &wdog2->wmcr);
@@ -255,6 +260,23 @@
writel(0, &mxc_ccm->ccdr);
}
+static void init_bandgap(void)
+{
+ struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
+ /*
+ * Ensure the bandgap has stabilized.
+ */
+ while (!(readl(&anatop->ana_misc0) & 0x80))
+ ;
+ /*
+ * For best noise performance of the analog blocks using the
+ * outputs of the bandgap, the reftop_selfbiasoff bit should
+ * be set.
+ */
+ writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set);
+}
+
+
#ifdef CONFIG_MX6SL
static void set_preclk_from_osc(void)
{
@@ -275,6 +297,13 @@
clear_mmdc_ch_mask();
/*
+ * Disable self-bias circuit in the analog bandap.
+ * The self-bias circuit is used by the bandgap during startup.
+ * This bit should be set after the bandgap has initialized.
+ */
+ init_bandgap();
+
+ /*
* When low freq boot is enabled, ROM will not set AHB
* freq, so we need to ensure AHB freq is 132MHz in such
* scenario.
diff --git a/arch/arm/imx-common/Makefile b/arch/arm/imx-common/Makefile
index 25a9d4c..606482f 100644
--- a/arch/arm/imx-common/Makefile
+++ b/arch/arm/imx-common/Makefile
@@ -24,6 +24,7 @@
endif
obj-$(CONFIG_CMD_BMODE) += cmd_bmode.o
obj-$(CONFIG_CMD_HDMIDETECT) += cmd_hdmidet.o
+obj-$(CONFIG_CMD_DEKBLOB) += cmd_dek.o
quiet_cmd_cpp_cfg = CFGS $@
cmd_cpp_cfg = $(CPP) $(cpp_flags) -x c -o $@ $<
diff --git a/arch/arm/imx-common/cmd_dek.c b/arch/arm/imx-common/cmd_dek.c
new file mode 100644
index 0000000..d93d5fb
--- /dev/null
+++ b/arch/arm/imx-common/cmd_dek.c
@@ -0,0 +1,91 @@
+/*
+ * Copyright 2008-2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Command for encapsulating DEK blob
+ */
+
+#include <common.h>
+#include <command.h>
+#include <environment.h>
+#include <malloc.h>
+#include <asm/byteorder.h>
+#include <linux/compiler.h>
+#include <fsl_sec.h>
+#include <asm/arch/clock.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/**
+* blob_dek() - Encapsulate the DEK as a blob using CAM's Key
+* @src: - Address of data to be encapsulated
+* @dst: - Desination address of encapsulated data
+* @len: - Size of data to be encapsulated
+*
+* Returns zero on success,and negative on error.
+*/
+static int blob_encap_dek(const u8 *src, u8 *dst, u32 len)
+{
+ int ret = 0;
+ u32 jr_size = 4;
+
+ u32 out_jr_size = sec_in32(CONFIG_SYS_FSL_JR0_ADDR + 0x102c);
+ if (out_jr_size != jr_size) {
+ hab_caam_clock_enable(1);
+ sec_init();
+ }
+
+ if (!((len == 128) | (len == 192) | (len == 256))) {
+ debug("Invalid DEK size. Valid sizes are 128, 192 and 256b\n");
+ return -1;
+ }
+
+ len /= 8;
+ ret = blob_dek(src, dst, len);
+
+ return ret;
+}
+
+/**
+ * do_dek_blob() - Handle the "dek_blob" command-line command
+ * @cmdtp: Command data struct pointer
+ * @flag: Command flag
+ * @argc: Command-line argument count
+ * @argv: Array of command-line arguments
+ *
+ * Returns zero on success, CMD_RET_USAGE in case of misuse and negative
+ * on error.
+ */
+static int do_dek_blob(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ uint32_t src_addr, dst_addr, len;
+ uint8_t *src_ptr, *dst_ptr;
+ int ret = 0;
+
+ if (argc != 4)
+ return CMD_RET_USAGE;
+
+ src_addr = simple_strtoul(argv[1], NULL, 16);
+ dst_addr = simple_strtoul(argv[2], NULL, 16);
+ len = simple_strtoul(argv[3], NULL, 10);
+
+ src_ptr = map_sysmem(src_addr, len/8);
+ dst_ptr = map_sysmem(dst_addr, BLOB_SIZE(len/8));
+
+ ret = blob_encap_dek(src_ptr, dst_ptr, len);
+
+ return ret;
+}
+
+/***************************************************/
+static char dek_blob_help_text[] =
+ "src dst len - Encapsulate and create blob of data\n"
+ " $len bits long at address $src and\n"
+ " store the result at address $dst.\n";
+
+U_BOOT_CMD(
+ dek_blob, 4, 1, do_dek_blob,
+ "Data Encryption Key blob encapsulation",
+ dek_blob_help_text
+);
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index 28ccd29..067d08f 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -24,13 +24,16 @@
#include <fsl_esdhc.h>
#endif
-char *get_reset_cause(void)
+static u32 reset_cause = -1;
+
+static char *get_reset_cause(void)
{
u32 cause;
struct src *src_regs = (struct src *)SRC_BASE_ADDR;
cause = readl(&src_regs->srsr);
writel(cause, &src_regs->srsr);
+ reset_cause = cause;
switch (cause) {
case 0x00001:
@@ -53,6 +56,11 @@
}
}
+u32 get_imx_reset_cause(void)
+{
+ return reset_cause;
+}
+
#if defined(CONFIG_MX53) || defined(CONFIG_MX6)
#if defined(CONFIG_MX53)
#define MEMCTL_BASE ESDCTL_BASE_ADDR
diff --git a/arch/arm/imx-common/timer.c b/arch/arm/imx-common/timer.c
index 65ef60b..e522990 100644
--- a/arch/arm/imx-common/timer.c
+++ b/arch/arm/imx-common/timer.c
@@ -176,3 +176,20 @@
{
return gpt_get_clk();
}
+
+/*
+ * This function is intended for SHORT delays only.
+ * It will overflow at around 10 seconds @ 400MHz,
+ * or 20 seconds @ 200MHz.
+ */
+unsigned long usec2ticks(unsigned long usec)
+{
+ ulong ticks;
+
+ if (usec < 1000)
+ ticks = ((usec * (get_tbclk()/1000)) + 500) / 1000;
+ else
+ ticks = ((usec / 10) * (get_tbclk() / 100000));
+
+ return ticks;
+}
diff --git a/arch/arm/include/asm/arch-imx/cpu.h b/arch/arm/include/asm/arch-imx/cpu.h
index 254136e..4715f4e 100644
--- a/arch/arm/include/asm/arch-imx/cpu.h
+++ b/arch/arm/include/asm/arch-imx/cpu.h
@@ -17,3 +17,5 @@
#define CS0_64M_CS1_64M 1
#define CS0_64M_CS1_32M_CS2_32M 2
#define CS0_32M_CS1_32M_CS2_32M_CS3_32M 3
+
+u32 get_imx_reset_cause(void);
diff --git a/arch/arm/include/asm/arch-mx5/sys_proto.h b/arch/arm/include/asm/arch-mx5/sys_proto.h
index ac7705b..b06c77f 100644
--- a/arch/arm/include/asm/arch-mx5/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx5/sys_proto.h
@@ -24,6 +24,5 @@
int fecmxc_initialize(bd_t *bis);
u32 get_ahb_clk(void);
u32 get_periph_clk(void);
-char *get_reset_cause(void);
#endif
diff --git a/arch/arm/include/asm/arch-mx6/crm_regs.h b/arch/arm/include/asm/arch-mx6/crm_regs.h
index 39f3c07..0592ce0 100644
--- a/arch/arm/include/asm/arch-mx6/crm_regs.h
+++ b/arch/arm/include/asm/arch-mx6/crm_regs.h
@@ -1063,4 +1063,6 @@
#define BF_ANADIG_PFD_528_PFD0_FRAC(v) \
(((v) << 0) & BM_ANADIG_PFD_528_PFD0_FRAC)
+#define BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF 0x00000008
+
#endif /*__ARCH_ARM_MACH_MX6_CCM_REGS_H__ */
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index ae88b6e..9a4ad8b 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -215,6 +215,10 @@
#define AIPS2_OFF_BASE_ADDR (ATZ2_BASE_ADDR + 0x80000)
#define CAAM_BASE_ADDR (ATZ2_BASE_ADDR)
#define ARM_BASE_ADDR (ATZ2_BASE_ADDR + 0x40000)
+
+#define CONFIG_SYS_FSL_SEC_ADDR CAAM_BASE_ADDR
+#define CONFIG_SYS_FSL_JR0_ADDR (CAAM_BASE_ADDR + 0x1000)
+
#define USB_PL301_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x0000)
#define USB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x4000)
diff --git a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h
index 9ded3d8..6ba1034 100644
--- a/arch/arm/include/asm/arch-mx6/mx6sl_pins.h
+++ b/arch/arm/include/asm/arch-mx6/mx6sl_pins.h
@@ -31,7 +31,12 @@
MX6_PAD_SD2_DAT1__USDHC2_DAT1 = IOMUX_PAD(0x0568, 0x0260, 0, 0x0000, 0, 0),
MX6_PAD_SD2_DAT2__USDHC2_DAT2 = IOMUX_PAD(0x056C, 0x0264, 0, 0x0000, 0, 0),
MX6_PAD_SD2_DAT3__USDHC2_DAT3 = IOMUX_PAD(0x0570, 0x0268, 0, 0x0000, 0, 0),
+ MX6_PAD_SD2_DAT4__USDHC2_DAT4 = IOMUX_PAD(0X0574, 0X026C, 0, 0X0000, 0, 0),
+ MX6_PAD_SD2_DAT5__USDHC2_DAT5 = IOMUX_PAD(0X0578, 0X0270, 0, 0X0000, 0, 0),
+ MX6_PAD_SD2_DAT6__USDHC2_DAT6 = IOMUX_PAD(0X057C, 0X0274, 0, 0X0000, 0, 0),
+ MX6_PAD_SD2_DAT7__USDHC2_DAT7 = IOMUX_PAD(0X0580, 0X0278, 0, 0X0000, 0, 0),
MX6_PAD_SD2_DAT7__GPIO_5_0 = IOMUX_PAD(0x0580, 0x0278, 5, 0x0000, 0, 0),
+ MX6_PAD_SD2_RST__USDHC2_RST = IOMUX_PAD(0x0584, 0x027C, 0, 0x0000, 0, 0),
MX6_PAD_SD3_CLK__USDHC3_CLK = IOMUX_PAD(0x0588, 0x0280, 0, 0x0000, 0, 0),
MX6_PAD_SD3_CMD__USDHC3_CMD = IOMUX_PAD(0x058C, 0x0284, 0, 0x0000, 0, 0),
MX6_PAD_SD3_DAT0__USDHC3_DAT0 = IOMUX_PAD(0x0590, 0x0288, 0, 0x0000, 0, 0),
@@ -58,5 +63,10 @@
MX6_PAD_KEY_COL4__USB_USBOTG1_PWR = IOMUX_PAD(0x0484, 0x017C, 6, 0x0000, 0, 0),
MX6_PAD_KEY_COL5__USB_USBOTG2_PWR = IOMUX_PAD(0x0488, 0x0180, 6, 0x0000, 0, 0),
+
+ MX6_PAD_I2C1_SDA__I2C1_SDA = IOMUX_PAD(0x0450, 0x0160, 0x10, 0x0720, 2, 0),
+ MX6_PAD_I2C1_SDA__GPIO_3_13 = IOMUX_PAD(0x0450, 0x0160, 5, 0x0000, 0, 0),
+ MX6_PAD_I2C1_SCL__I2C1_SCL = IOMUX_PAD(0x044C, 0x015C, 0x10, 0x071C, 2, 0),
+ MX6_PAD_I2C1_SCL__GPIO_3_12 = IOMUX_PAD(0x044C, 0x015C, 5, 0x0000, 0, 0),
};
#endif /* __ASM_ARCH_MX6_MX6SL_PINS_H__ */
diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c
index e8ea256..d46b8db 100644
--- a/board/boundary/nitrogen6x/nitrogen6x.c
+++ b/board/boundary/nitrogen6x/nitrogen6x.c
@@ -1018,5 +1018,6 @@
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
+ setenv_hex("reset_cause", get_imx_reset_cause());
return 0;
}
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c
index 2cd1794..4980bf7 100644
--- a/board/freescale/common/pfuze.c
+++ b/board/freescale/common/pfuze.c
@@ -5,9 +5,47 @@
*/
#include <common.h>
+#include <errno.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
+int pfuze_mode_init(struct pmic *p, u32 mode)
+{
+ unsigned char offset, i, switch_num;
+ u32 id, ret;
+
+ pmic_reg_read(p, PFUZE100_DEVICEID, &id);
+ id = id & 0xf;
+
+ if (id == 0) {
+ switch_num = 6;
+ offset = PFUZE100_SW1CMODE;
+ } else if (id == 1) {
+ switch_num = 4;
+ offset = PFUZE100_SW2MODE;
+ } else {
+ printf("Not supported, id=%d\n", id);
+ return -EINVAL;
+ }
+
+ ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
+ if (ret < 0) {
+ printf("Set SW1AB mode error!\n");
+ return ret;
+ }
+
+ for (i = 0; i < switch_num - 1; i++) {
+ ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
+ if (ret < 0) {
+ printf("Set switch 0x%x mode error!\n",
+ offset + i * SWITCH_SIZE);
+ return ret;
+ }
+ }
+
+ return ret;
+}
+
struct pmic *pfuze_common_init(unsigned char i2cbus)
{
struct pmic *p;
diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h
index 7a4126c..53cfc99 100644
--- a/board/freescale/common/pfuze.h
+++ b/board/freescale/common/pfuze.h
@@ -8,5 +8,6 @@
#define __PFUZE_BOARD_HELPER__
struct pmic *pfuze_common_init(unsigned char i2cbus);
+int pfuze_mode_init(struct pmic *p, u32 mode);
#endif
diff --git a/board/freescale/mx25pdk/mx25pdk.c b/board/freescale/mx25pdk/mx25pdk.c
index 71a395c..01dac72 100644
--- a/board/freescale/mx25pdk/mx25pdk.c
+++ b/board/freescale/mx25pdk/mx25pdk.c
@@ -146,8 +146,8 @@
if (!p)
return -ENODEV;
- /* Turn on Ethernet PHY supply */
- pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE);
+ /* Turn on Ethernet PHY and LCD supplies */
+ pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE | ONOFFA);
return 0;
}
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index efcf4b3..9ece6ec 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -366,22 +366,6 @@
return 0;
}
-#if defined(CONFIG_DISPLAY_CPUINFO)
-int print_cpuinfo(void)
-{
- u32 cpurev;
-
- cpurev = get_cpu_rev();
- printf("CPU: Freescale i.MX%x family rev%d.%d at %d MHz\n",
- (cpurev & 0xFF000) >> 12,
- (cpurev & 0x000F0) >> 4,
- (cpurev & 0x0000F) >> 0,
- mxc_get_clock(MXC_ARM_CLK) / 1000000);
- printf("Reset cause: %s\n", get_reset_cause());
- return 0;
-}
-#endif
-
/*
* Do not overwrite the console
* Use always serial for U-Boot console
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index a90360f..b76e4eb 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -29,6 +29,7 @@
#include <asm/arch/crm_regs.h>
#include <pca953x.h>
#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -494,11 +495,16 @@
int power_init_board(void)
{
struct pmic *p;
+ unsigned int ret;
p = pfuze_common_init(I2C_PMIC);
if (!p)
return -ENODEV;
+ ret = pfuze_mode_init(p, APS_PFM);
+ if (ret < 0)
+ return ret;
+
return 0;
}
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 2f7198d..bb2dd96 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -631,12 +631,16 @@
int power_init_board(void)
{
struct pmic *p;
- unsigned int reg;
+ unsigned int reg, ret;
p = pfuze_common_init(I2C_PMIC);
if (!p)
return -ENODEV;
+ ret = pfuze_mode_init(p, APS_PFM);
+ if (ret < 0)
+ return ret;
+
/* Increase VGEN3 from 2.5 to 2.8V */
pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
reg &= ~LDO_VOL_MASK;
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index 838ea6c..7c18c90 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -13,13 +13,18 @@
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/spi.h>
#include <asm/io.h>
#include <linux/sizes.h>
#include <common.h>
#include <fsl_esdhc.h>
+#include <i2c.h>
#include <mmc.h>
#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
#include <usb.h>
#include <usb/ehci-fsl.h>
@@ -40,6 +45,16 @@
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\
+ PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
+ PAD_CTL_SRE_FAST)
+
#define ETH_PHY_RESET IMX_GPIO_NR(4, 21)
int dram_init(void)
@@ -221,6 +236,34 @@
return 0;
}
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+struct i2c_pads_info i2c_pad_info1 = {
+ .sda = {
+ .i2c_mode = MX6_PAD_I2C1_SDA__I2C1_SDA | PC,
+ .gpio_mode = MX6_PAD_I2C1_SDA__GPIO_3_13 | PC,
+ .gp = IMX_GPIO_NR(3, 13),
+ },
+ .scl = {
+ .i2c_mode = MX6_PAD_I2C1_SCL__I2C1_SCL | PC,
+ .gpio_mode = MX6_PAD_I2C1_SCL__GPIO_3_12 | PC,
+ .gp = IMX_GPIO_NR(3, 12),
+ },
+};
+
+int power_init_board(void)
+{
+ struct pmic *p;
+
+ p = pfuze_common_init(I2C_PMIC);
+ if (!p)
+ return -ENODEV;
+
+ return pfuze_mode_init(p, APS_PFM);
+}
+#endif
+
#ifdef CONFIG_FEC_MXC
int board_eth_init(bd_t *bis)
{
@@ -247,7 +290,7 @@
static iomux_v3_cfg_t const usb_otg_pads[] = {
/* OTG1 */
MX6_PAD_KEY_COL4__USB_USBOTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_EPDC_PWRCOM__ANATOP_USBOTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EPDC_PWRCOM__ANATOP_USBOTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
/* OTG2 */
MX6_PAD_KEY_COL5__USB_USBOTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
};
@@ -297,6 +340,10 @@
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+#ifdef CONFIG_SYS_I2C_MXC
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+#endif
+
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index a2c9aae..2ff960e 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -199,12 +199,16 @@
int power_init_board(void)
{
struct pmic *p;
- unsigned int reg;
+ unsigned int reg, ret;
p = pfuze_common_init(I2C_PMIC);
if (!p)
return -ENODEV;
+ ret = pfuze_mode_init(p, APS_PFM);
+ if (ret < 0)
+ return ret;
+
/* Enable power of VGEN5 3V3, needed for SD3 */
pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
reg &= ~LDO_VOL_MASK;
diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c
index dfa430e..42b166d 100644
--- a/board/tbs/tbs2910/tbs2910.c
+++ b/board/tbs/tbs2910/tbs2910.c
@@ -326,21 +326,25 @@
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
writel(reg, &ccm->analog_pll_video);
- /* select video pll for ldb_di0_clk */
- reg = readl(&ccm->cs2cdr);
- reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK);
- writel(reg, &ccm->cs2cdr);
+ /* gate ipu1_di0_clk */
+ reg = readl(&ccm->CCGR3);
+ reg &= ~MXC_CCM_CCGR3_LDB_DI0_MASK;
+ writel(reg, &ccm->CCGR3);
- /* select ldb_di0_clk / 7 for ldb_di0_ipu_clk */
- reg = readl(&ccm->cscmr2);
- reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
- writel(reg, &ccm->cscmr2);
-
- /* select ldb_di0_ipu_clk for ipu1_di0_clk -> 65MHz pixclock */
+ /* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
reg = readl(&ccm->chsccdr);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
+ MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
+ reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
+ (6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
+ (0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &ccm->chsccdr);
+
+ /* enable ipu1_di0_clk */
+ reg = readl(&ccm->CCGR3);
+ reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
+ writel(reg, &ccm->CCGR3);
}
#endif /* CONFIG_VIDEO_IPUV3 */
diff --git a/board/warp/Kconfig b/board/warp/Kconfig
new file mode 100644
index 0000000..7b569cc
--- /dev/null
+++ b/board/warp/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_WARP
+
+config SYS_BOARD
+ default "warp"
+
+config SYS_SOC
+ default "mx6"
+
+config SYS_CONFIG_NAME
+ default "warp"
+
+endif
diff --git a/board/warp/MAINTAINERS b/board/warp/MAINTAINERS
new file mode 100644
index 0000000..ee2114d
--- /dev/null
+++ b/board/warp/MAINTAINERS
@@ -0,0 +1,6 @@
+WaRP BOARD
+M: Otavio Salvador <otavio@ossystems.com.br>
+S: Maintained
+F: board/warp/
+F: include/configs/warp.h
+F: configs/warp_defconfig
diff --git a/board/warp/Makefile b/board/warp/Makefile
new file mode 100644
index 0000000..c555f87
--- /dev/null
+++ b/board/warp/Makefile
@@ -0,0 +1,8 @@
+# Copyright (C) 2014 O.S. Systems Software LTDA.
+# Copyright (C) 2014 Kynetics LLC.
+# Copyright (C) 2014 Revolution Robotics, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := warp.o
diff --git a/board/warp/warp.c b/board/warp/warp.c
new file mode 100644
index 0000000..21ac5e7
--- /dev/null
+++ b/board/warp/warp.c
@@ -0,0 +1,119 @@
+/*
+ * Copyright (C) 2014, 2015 O.S. Systems Software LTDA.
+ * Copyright (C) 2014 Kynetics LLC.
+ * Copyright (C) 2014 Revolution Robotics, Inc.
+ *
+ * Author: Otavio Salvador <otavio@ossystems.com.br>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/io.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <watchdog.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <usb.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS | \
+ PAD_CTL_LVE)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_22K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS | \
+ PAD_CTL_LVE)
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+static void setup_iomux_uart(void)
+{
+ static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC2_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1; /* Assume boot SD always present */
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_RST__USDHC2_RST | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT4__USDHC2_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT5__USDHC2_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT6__USDHC2_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT7__USDHC2_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+int board_usb_phy_mode(int port)
+{
+ return USB_INIT_DEVICE;
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_HW_WATCHDOG
+ hw_watchdog_init();
+#endif
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: WaRP Board\n");
+
+ return 0;
+}
diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c
index 29f0f1f..e9904cd 100644
--- a/common/cmd_eeprom.c
+++ b/common/cmd_eeprom.c
@@ -161,6 +161,9 @@
#if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
spi_read (addr, alen, buffer, len);
#else
+#if defined(CONFIG_SYS_I2C_EEPROM_BUS)
+ i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
+#endif
if (i2c_read(addr[0], offset, alen - 1, buffer, len))
rcode = 1;
#endif
@@ -339,6 +342,9 @@
/* Write is enabled ... now write eeprom value.
*/
#endif
+#if defined(CONFIG_SYS_I2C_EEPROM_BUS)
+ i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
+#endif
if (i2c_write(addr[0], offset, alen - 1, buffer, len))
rcode = 1;
diff --git a/configs/warp_defconfig b/configs/warp_defconfig
new file mode 100644
index 0000000..624a8af
--- /dev/null
+++ b/configs/warp_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL"
+CONFIG_ARM=y
+CONFIG_TARGET_WARP=y
diff --git a/doc/README.fsl-esdhc b/doc/README.fsl-esdhc
index b70f271..619c6b2 100644
--- a/doc/README.fsl-esdhc
+++ b/doc/README.fsl-esdhc
@@ -1,5 +1,6 @@
CONFIG_SYS_FSL_ESDHC_LE means ESDHC IP is in little-endian mode.
CONFIG_SYS_FSL_ESDHC_BE means ESDHC IP is in big-endian mode.
+CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT forces to run at 1.8V.
Accessing ESDHC registers can be determined by ESDHC IP's endian
mode or processor's endian mode.
diff --git a/doc/README.mxc_hab b/doc/README.mxc_hab
index 43e64a2..e9340dd 100644
--- a/doc/README.mxc_hab
+++ b/doc/README.mxc_hab
@@ -46,3 +46,51 @@
NOTE: U-Boot_CSF.bin needs to be padded to the value specified in
the imximage.cfg file.
+
+Setup U-Boot Image for Encrypted Boot
+-------------------------------------
+An authenticated U-Boot image is used as starting point for
+Encrypted Boot. The image is encrypted by Freescale's Code
+Signing Tool (CST). The CST replaces only the image data of
+u-boot.imx with the encrypted data. The Initial Vector Table,
+DCD, and Boot data, remains in plaintext.
+
+The image data is encrypted with a Encryption Key (DEK).
+Therefore, this key is needed to decrypt the data during the
+booting process. The DEK is protected by wrapping it in a Blob,
+which needs to be appended to the U-Boot image and specified in
+the CSF file.
+
+The DEK blob is generated by an authenticated U-Boot image with
+the dek_blob cmd enabled. The image used for DEK blob generation
+needs to have the following configurations enabled:
+
+CONFIG_SECURE_BOOT
+CONFIG_SYS_FSL_SEC_COMPAT 4 /* HAB version */
+CONFIG_FSL_CAAM
+CONFIG_CMD_DEKBLOB
+
+Note: The encrypted boot feature is only supported by HABv4 or
+greater.
+
+The dek_blob command then can be used to generate the DEK blob of
+a DEK previously loaded in memory. The command is used as follows:
+
+dek_blob <DEK address> <Output Address> <Key Size in Bits>
+example: dek_blob 0x10800000 0x10801000 192
+
+The resulting DEK blob then is used to construct the encrypted
+U-Boot image. Note that the blob needs to be transferred back
+to the host.Then the following commands are used to construct
+the final image.
+
+objcopy -I binary -O binary --pad-to 0x2000 --gap-fill=0x00 \
+ U-Boot_CSF.bin U-Boot_CSF_pad.bin
+cat u-boot.imx U-Boot_CSF_pad.bin > u-boot-signed.imx
+objcopy -I binary -O binary --pad-to <blob_dst> --gap-fill=0x00 \
+ u-boot-signed.imx u-boot-signed-pad.bin
+cat u-boot-signed-pad.imx DEK_blob.bin > u-boot-encrypted.imx
+
+ NOTE: u-boot-signed.bin needs to be padded to the value
+ equivalent to the address in which the DEK blob is specified
+ in the CSF.
diff --git a/drivers/crypto/fsl/Makefile b/drivers/crypto/fsl/Makefile
index c0cf642..4aa91e4 100644
--- a/drivers/crypto/fsl/Makefile
+++ b/drivers/crypto/fsl/Makefile
@@ -8,5 +8,5 @@
obj-y += sec.o
obj-$(CONFIG_FSL_CAAM) += jr.o fsl_hash.o jobdesc.o error.o
-obj-$(CONFIG_CMD_BLOB) += fsl_blob.o
+obj-$(CONFIG_CMD_BLOB)$(CONFIG_CMD_DEKBLOB) += fsl_blob.o
obj-$(CONFIG_RSA_FREESCALE_EXP) += fsl_rsa.o
diff --git a/drivers/crypto/fsl/desc.h b/drivers/crypto/fsl/desc.h
index 504f2b0..18e2ec8 100644
--- a/drivers/crypto/fsl/desc.h
+++ b/drivers/crypto/fsl/desc.h
@@ -12,11 +12,18 @@
#ifndef DESC_H
#define DESC_H
+#define KEY_BLOB_SIZE 32
+#define MAC_SIZE 16
+
/* Max size of any CAAM descriptor in 32-bit words, inclusive of header */
#define MAX_CAAM_DESCSIZE 64
+/* Size of DEK Blob descriptor, inclusive of header */
+#define DEK_BLOB_DESCSIZE 9
+
/* Block size of any entity covered/uncovered with a KEK/TKEK */
#define KEK_BLOCKSIZE 16
+
/*
* Supported descriptor command types as they show up
* inside a descriptor command word.
@@ -273,6 +280,13 @@
#define LDLEN_SET_OFIFO_OFFSET_MASK (3 << LDLEN_SET_OFIFO_OFFSET_SHIFT)
/*
+ * AAD Definitions
+ */
+#define AES_KEY_SHIFT 8
+#define LD_CCM_MODE 0x66
+#define KEY_AES_SRC (0x55 << AES_KEY_SHIFT)
+
+/*
* FIFO_LOAD/FIFO_STORE/SEQ_FIFO_LOAD/SEQ_FIFO_STORE
* Command Constructs
*/
@@ -418,6 +432,7 @@
#define OP_PCLID_MASK (0xff << 16)
/* Assuming OP_TYPE = OP_TYPE_UNI_PROTOCOL */
+#define OP_PCLID_SECMEM 0x08
#define OP_PCLID_BLOB (0x0d << OP_PCLID_SHIFT)
#define OP_PCLID_SECRETKEY (0x11 << OP_PCLID_SHIFT)
#define OP_PCLID_PUBLICKEYPAIR (0x14 << OP_PCLID_SHIFT)
diff --git a/drivers/crypto/fsl/fsl_blob.c b/drivers/crypto/fsl/fsl_blob.c
index 9923bcb..8b25921 100644
--- a/drivers/crypto/fsl/fsl_blob.c
+++ b/drivers/crypto/fsl/fsl_blob.c
@@ -7,6 +7,8 @@
#include <common.h>
#include <malloc.h>
+#include <fsl_sec.h>
+#include <asm-generic/errno.h>
#include "jobdesc.h"
#include "desc.h"
#include "jr.h"
@@ -59,3 +61,53 @@
free(desc);
return ret;
}
+
+#ifdef CONFIG_CMD_DEKBLOB
+int blob_dek(const u8 *src, u8 *dst, u8 len)
+{
+ int ret, size, i = 0;
+ u32 *desc;
+
+ int out_sz = WRP_HDR_SIZE + len + KEY_BLOB_SIZE + MAC_SIZE;
+
+ puts("\nEncapsulating provided DEK to form blob\n");
+ desc = memalign(ARCH_DMA_MINALIGN,
+ sizeof(uint32_t) * DEK_BLOB_DESCSIZE);
+ if (!desc) {
+ debug("Not enough memory for descriptor allocation\n");
+ return -ENOMEM;
+ }
+
+ ret = inline_cnstr_jobdesc_blob_dek(desc, src, dst, len);
+ if (ret) {
+ debug("Error in Job Descriptor Construction: %d\n", ret);
+ } else {
+ size = roundup(sizeof(uint32_t) * DEK_BLOB_DESCSIZE,
+ ARCH_DMA_MINALIGN);
+ flush_dcache_range((unsigned long)desc,
+ (unsigned long)desc + size);
+ size = roundup(sizeof(uint8_t) * out_sz, ARCH_DMA_MINALIGN);
+ flush_dcache_range((unsigned long)dst,
+ (unsigned long)dst + size);
+
+ ret = run_descriptor_jr(desc);
+ }
+
+ if (ret) {
+ debug("Error in Encapsulation %d\n", ret);
+ goto err;
+ }
+
+ size = roundup(out_sz, ARCH_DMA_MINALIGN);
+ invalidate_dcache_range((unsigned long)dst, (unsigned long)dst+size);
+
+ puts("DEK Blob\n");
+ for (i = 0; i < out_sz; i++)
+ printf("%02X", ((uint8_t *)dst)[i]);
+ printf("\n");
+
+err:
+ free(desc);
+ return ret;
+}
+#endif
diff --git a/drivers/crypto/fsl/jobdesc.c b/drivers/crypto/fsl/jobdesc.c
index cc0dced..5695bef 100644
--- a/drivers/crypto/fsl/jobdesc.c
+++ b/drivers/crypto/fsl/jobdesc.c
@@ -9,12 +9,157 @@
*/
#include <common.h>
+#include <fsl_sec.h>
#include "desc_constr.h"
#include "jobdesc.h"
#include "rsa_caam.h"
-#define KEY_BLOB_SIZE 32
-#define MAC_SIZE 16
+#ifdef CONFIG_MX6
+/*!
+ * Secure memory run command
+ *
+ * @param sec_mem_cmd Secure memory command register
+ * @return cmd_status Secure memory command status register
+ */
+uint32_t secmem_set_cmd(uint32_t sec_mem_cmd)
+{
+ uint32_t temp_reg;
+
+ sec_out32(CAAM_SMCJR0, sec_mem_cmd);
+
+ do {
+ temp_reg = sec_in32(CAAM_SMCSJR0);
+ } while (temp_reg & CMD_COMPLETE);
+
+ return temp_reg;
+}
+
+/*!
+ * CAAM page allocation:
+ * Allocates a partition from secure memory, with the id
+ * equal to partion_num. This will de-allocate the page
+ * if it is already allocated. The partition will have
+ * full access permissions. The permissions are set before,
+ * running a job descriptor. A memory page of secure RAM
+ * is allocated for the partition.
+ *
+ * @param page Number of the page to allocate.
+ * @param partition Number of the partition to allocate.
+ * @return 0 on success, ERROR_IN_PAGE_ALLOC otherwise
+ */
+int caam_page_alloc(uint8_t page_num, uint8_t partition_num)
+{
+ uint32_t temp_reg;
+
+ /*
+ * De-Allocate partition_num if already allocated to ARM core
+ */
+ if (sec_in32(CAAM_SMPO_0) & PARTITION_OWNER(partition_num)) {
+ temp_reg = secmem_set_cmd(PARTITION(partition_num) |
+ CMD_PART_DEALLOC);
+ if (temp_reg & SMCSJR_AERR) {
+ printf("Error: De-allocation status 0x%X\n", temp_reg);
+ return ERROR_IN_PAGE_ALLOC;
+ }
+ }
+
+ /* set the access rights to allow full access */
+ sec_out32(CAAM_SMAG1JR0(partition_num), 0xF);
+ sec_out32(CAAM_SMAG2JR0(partition_num), 0xF);
+ sec_out32(CAAM_SMAPJR0(partition_num), 0xFF);
+
+ /* Now need to allocate partition_num of secure RAM. */
+ /* De-Allocate page_num by starting with a page inquiry command */
+ temp_reg = secmem_set_cmd(PAGE(page_num) | CMD_INQUIRY);
+
+ /* if the page is owned, de-allocate it */
+ if ((temp_reg & SMCSJR_PO) == PAGE_OWNED) {
+ temp_reg = secmem_set_cmd(PAGE(page_num) | CMD_PAGE_DEALLOC);
+ if (temp_reg & SMCSJR_AERR) {
+ printf("Error: Allocation status 0x%X\n", temp_reg);
+ return ERROR_IN_PAGE_ALLOC;
+ }
+ }
+
+ /* Allocate page_num to partition_num */
+ temp_reg = secmem_set_cmd(PAGE(page_num) | PARTITION(partition_num)
+ | CMD_PAGE_ALLOC);
+ if (temp_reg & SMCSJR_AERR) {
+ printf("Error: Allocation status 0x%X\n", temp_reg);
+ return ERROR_IN_PAGE_ALLOC;
+ }
+ /* page inquiry command to ensure that the page was allocated */
+ temp_reg = secmem_set_cmd(PAGE(page_num) | CMD_INQUIRY);
+
+ /* if the page is not owned => problem */
+ if ((temp_reg & SMCSJR_PO) != PAGE_OWNED) {
+ printf("Allocation of page %d in partition %d failed 0x%X\n",
+ temp_reg, page_num, partition_num);
+
+ return ERROR_IN_PAGE_ALLOC;
+ }
+
+ return 0;
+}
+
+int inline_cnstr_jobdesc_blob_dek(uint32_t *desc, const uint8_t *plain_txt,
+ uint8_t *dek_blob, uint32_t in_sz)
+{
+ uint32_t ret = 0;
+ u32 aad_w1, aad_w2;
+ /* output blob will have 32 bytes key blob in beginning and
+ * 16 byte HMAC identifier at end of data blob */
+ uint32_t out_sz = in_sz + KEY_BLOB_SIZE + MAC_SIZE;
+ /* Setting HDR for blob */
+ uint8_t wrapped_key_hdr[8] = {HDR_TAG, 0x00, WRP_HDR_SIZE + out_sz,
+ HDR_PAR, HAB_MOD, HAB_ALG, in_sz, HAB_FLG};
+
+ /* initialize the blob array */
+ memset(dek_blob, 0, out_sz + 8);
+ /* Copy the header into the DEK blob buffer */
+ memcpy(dek_blob, wrapped_key_hdr, sizeof(wrapped_key_hdr));
+
+ /* allocating secure memory */
+ ret = caam_page_alloc(PAGE_1, PARTITION_1);
+ if (ret)
+ return ret;
+
+ /* Write DEK to secure memory */
+ memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
+
+ unsigned long start = (unsigned long)SEC_MEM_PAGE1 &
+ ~(ARCH_DMA_MINALIGN - 1);
+ unsigned long end = ALIGN(start + 0x1000, ARCH_DMA_MINALIGN);
+ flush_dcache_range(start, end);
+
+ /* Now configure the access rights of the partition */
+ sec_out32(CAAM_SMAG1JR0(PARTITION_1), KS_G1); /* set group 1 */
+ sec_out32(CAAM_SMAG2JR0(PARTITION_1), 0); /* clear group 2 */
+ sec_out32(CAAM_SMAPJR0(PARTITION_1), PERM); /* set perm & locks */
+
+ /* construct aad for AES */
+ aad_w1 = (in_sz << OP_ALG_ALGSEL_SHIFT) | KEY_AES_SRC | LD_CCM_MODE;
+ aad_w2 = 0x0;
+
+ init_job_desc(desc, 0);
+
+ append_cmd(desc, CMD_LOAD | CLASS_2 | KEY_IMM | KEY_ENC |
+ (0x0c << LDST_OFFSET_SHIFT) | 0x08);
+
+ append_u32(desc, aad_w1);
+
+ append_u32(desc, aad_w2);
+
+ append_cmd_ptr(desc, (dma_addr_t)SEC_MEM_PAGE1, in_sz, CMD_SEQ_IN_PTR);
+
+ append_cmd_ptr(desc, (dma_addr_t)dek_blob + 8, out_sz, CMD_SEQ_OUT_PTR);
+
+ append_operation(desc, OP_TYPE_ENCAP_PROTOCOL | OP_PCLID_BLOB |
+ OP_PCLID_SECMEM);
+
+ return ret;
+}
+#endif
void inline_cnstr_jobdesc_hash(uint32_t *desc,
const uint8_t *msg, uint32_t msgsz, uint8_t *digest,
diff --git a/drivers/crypto/fsl/jobdesc.h b/drivers/crypto/fsl/jobdesc.h
index 84b3edd..112404c 100644
--- a/drivers/crypto/fsl/jobdesc.h
+++ b/drivers/crypto/fsl/jobdesc.h
@@ -14,6 +14,20 @@
#define KEY_IDNFR_SZ_BYTES 16
+#ifdef CONFIG_CMD_DEKBLOB
+/* inline_cnstr_jobdesc_blob_dek:
+ * Intializes and constructs the job descriptor for DEK encapsulation
+ * using the given parameters.
+ * @desc: reference to the job descriptor
+ * @plain_txt: reference to the DEK
+ * @enc_blob: reference where to store the blob
+ * @in_sz: size in bytes of the DEK
+ * @return: 0 on success, ECONSTRJDESC otherwise
+ */
+int inline_cnstr_jobdesc_blob_dek(uint32_t *desc, const uint8_t *plain_txt,
+ uint8_t *enc_blob, uint32_t in_sz);
+#endif
+
void inline_cnstr_jobdesc_hash(uint32_t *desc,
const uint8_t *msg, uint32_t msgsz, uint8_t *digest,
u32 alg_type, uint32_t alg_size, int sg_tbl);
diff --git a/drivers/crypto/fsl/jr.c b/drivers/crypto/fsl/jr.c
index f9d4938..f99d594 100644
--- a/drivers/crypto/fsl/jr.c
+++ b/drivers/crypto/fsl/jr.c
@@ -90,11 +90,13 @@
jr.liodn = DEFAULT_JR_LIODN;
#endif
jr.size = JR_SIZE;
- jr.input_ring = (dma_addr_t *)malloc(JR_SIZE * sizeof(dma_addr_t));
+ jr.input_ring = (dma_addr_t *)memalign(ARCH_DMA_MINALIGN,
+ JR_SIZE * sizeof(dma_addr_t));
if (!jr.input_ring)
return -1;
jr.output_ring =
- (struct op_ring *)malloc(JR_SIZE * sizeof(struct op_ring));
+ (struct op_ring *)memalign(ARCH_DMA_MINALIGN,
+ JR_SIZE * sizeof(struct op_ring));
if (!jr.output_ring)
return -1;
@@ -163,13 +165,23 @@
CIRC_SPACE(jr.head, jr.tail, jr.size) <= 0)
return -1;
- jr.input_ring[head] = desc_phys_addr;
jr.info[head].desc_phys_addr = desc_phys_addr;
jr.info[head].desc_addr = (uint32_t)desc_addr;
jr.info[head].callback = (void *)callback;
jr.info[head].arg = arg;
jr.info[head].op_done = 0;
+ unsigned long start = (unsigned long)&jr.info[head] &
+ ~(ARCH_DMA_MINALIGN - 1);
+ unsigned long end = ALIGN(start + sizeof(struct jr_info),
+ ARCH_DMA_MINALIGN);
+ flush_dcache_range(start, end);
+
+ jr.input_ring[head] = desc_phys_addr;
+ start = (unsigned long)&jr.input_ring[head] & ~(ARCH_DMA_MINALIGN - 1);
+ end = ALIGN(start + sizeof(dma_addr_t), ARCH_DMA_MINALIGN);
+ flush_dcache_range(start, end);
+
jr.head = (head + 1) & (jr.size - 1);
sec_out32(®s->irja, 1);
@@ -187,6 +199,13 @@
void *arg = NULL;
while (sec_in32(®s->orsf) && CIRC_CNT(jr.head, jr.tail, jr.size)) {
+ unsigned long start = (unsigned long)jr.output_ring &
+ ~(ARCH_DMA_MINALIGN - 1);
+ unsigned long end = ALIGN(start +
+ sizeof(struct op_ring)*JR_SIZE,
+ ARCH_DMA_MINALIGN);
+ invalidate_dcache_range(start, end);
+
found = 0;
dma_addr_t op_desc = jr.output_ring[jr.tail].desc;
@@ -333,13 +352,17 @@
memset(&op, 0, sizeof(struct result));
- desc = malloc(sizeof(int) * 6);
+ desc = memalign(ARCH_DMA_MINALIGN, sizeof(uint32_t) * 6);
if (!desc) {
printf("cannot allocate RNG init descriptor memory\n");
return -1;
}
inline_cnstr_jobdesc_rng_instantiation(desc);
+ int size = roundup(sizeof(uint32_t) * 6, ARCH_DMA_MINALIGN);
+ flush_dcache_range((unsigned long)desc,
+ (unsigned long)desc + size);
+
ret = run_descriptor_jr(desc);
if (ret)
diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index f5d2ccb..c5e270d 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -54,19 +54,21 @@
uint fevt; /* Force event register */
uint admaes; /* ADMA error status register */
uint adsaddr; /* ADMA system address register */
- char reserved2[160]; /* reserved */
+ char reserved2[100]; /* reserved */
+ uint vendorspec; /* Vendor Specific register */
+ char reserved3[59]; /* reserved */
uint hostver; /* Host controller version register */
- char reserved3[4]; /* reserved */
- uint dmaerraddr; /* DMA error address register */
char reserved4[4]; /* reserved */
- uint dmaerrattr; /* DMA error attribute register */
+ uint dmaerraddr; /* DMA error address register */
char reserved5[4]; /* reserved */
+ uint dmaerrattr; /* DMA error attribute register */
+ char reserved6[4]; /* reserved */
uint hostcapblt2; /* Host controller capabilities register 2 */
- char reserved6[8]; /* reserved */
+ char reserved7[8]; /* reserved */
uint tcr; /* Tuning control register */
- char reserved7[28]; /* reserved */
+ char reserved8[28]; /* reserved */
uint sddirctl; /* SD direction control register */
- char reserved8[712]; /* reserved */
+ char reserved9[712]; /* reserved */
uint scr; /* eSDHC control register */
};
@@ -342,6 +344,15 @@
goto out;
}
+ /* Switch voltage to 1.8V if CMD11 succeeded */
+ if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) {
+ esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
+
+ printf("Run CMD11 1.8V switch\n");
+ /* Sleep for 5 ms - max time for card to switch to 1.8V */
+ udelay(5000);
+ }
+
/* Workaround for ESDHC errata ENGcm03648 */
if (!data && (cmd->resp_type & MMC_RSP_BUSY)) {
int timeout = 2500;
@@ -414,6 +425,10 @@
while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD))
;
}
+
+ /* If this was CMD11, then notify that power cycle is needed */
+ if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V)
+ printf("CMD11 to switch to 1.8V mode failed, card requires power cycle.\n");
}
esdhc_write32(®s->irqstat, -1);
@@ -509,6 +524,10 @@
/* Set timout to the maximum value */
esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
+#ifdef CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
+ esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
+#endif
+
return 0;
}
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
index 42bc3c8..8d8b93c 100644
--- a/include/configs/mx53loco.h
+++ b/include/configs/mx53loco.h
@@ -24,6 +24,8 @@
#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_CPUINFO
+
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h
index 4aa8101..f0e37f0 100644
--- a/include/configs/mx6sabre_common.h
+++ b/include/configs/mx6sabre_common.h
@@ -53,6 +53,8 @@
#define CONFIG_GENERIC_MMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
@@ -276,4 +278,18 @@
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_CI_UDC
+#define CONFIG_USBD_HS
+#define CONFIG_USB_GADGET_DUALSPEED
+
+#define CONFIG_USB_GADGET
+#define CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USBDOWNLOAD_GADGET
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+
+#define CONFIG_G_DNL_VENDOR_NUM 0x0525
+#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
+#define CONFIG_G_DNL_MANUFACTURER "FSL"
+
#endif /* __MX6QSABRE_COMMON_CONFIG_H */
diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h
index c567d9d..1221418 100644
--- a/include/configs/mx6slevk.h
+++ b/include/configs/mx6slevk.h
@@ -48,6 +48,18 @@
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
+
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
diff --git a/include/configs/ot1200.h b/include/configs/ot1200.h
index c061e93..3c60b4f 100644
--- a/include/configs/ot1200.h
+++ b/include/configs/ot1200.h
@@ -131,6 +131,16 @@
#define CONFIG_PHYLIB
#define CONFIG_PHY_SMSC
+#ifndef CONFIG_SPL
+#define CONFIG_CMD_EEPROM
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_BUS 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#endif
+
/* Miscellaneous commands */
#define CONFIG_CMD_BMODE
#define CONFIG_CMD_SETEXPR
diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h
index c097b98..7089378 100644
--- a/include/configs/tbs2910.h
+++ b/include/configs/tbs2910.h
@@ -165,6 +165,19 @@
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB_MASS_STORAGE
+#ifdef CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_CI_UDC
+#define CONFIG_USBD_HS
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW 0
+#define CONFIG_USBDOWNLOAD_GADGET
+#define CONFIG_G_DNL_VENDOR_NUM 0x0525
+#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
+#define CONFIG_G_DNL_MANUFACTURER "TBS"
+#endif /* CONFIG_CMD_USB_MASS_STORAGE */
#define CONFIG_USB_KEYBOARD
#ifdef CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE
diff --git a/include/configs/warp.h b/include/configs/warp.h
new file mode 100644
index 0000000..bcdd112
--- /dev/null
+++ b/include/configs/warp.h
@@ -0,0 +1,228 @@
+/*
+ * Copyright (C) 2014 O.S. Systems Software LTDA.
+ * Copyright (C) 2014 Kynetics LLC.
+ * Copyright (C) 2014 Revolution Robotics, Inc.
+ *
+ * Author: Otavio Salvador <otavio@ossystems.com.br>
+ *
+ * Configuration settings for the WaRP Board
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+#define CONFIG_MX6
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+/* Command definition */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_LOADADDR 0x82000000
+#define CONFIG_SYS_TEXT_BASE 0x87800000
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256
+
+/* Watchdog */
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS 30000 /* 30s */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + SZ_256M)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_512M
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_ENV_OFFSET (6 * SZ_64K)
+#define CONFIG_ENV_SIZE SZ_8K
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+/* VDD voltage 1.65 - 1.95 */
+#define CONFIG_SYS_SD_VOLTAGE 0x00000080
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Only OTG2 port enabled */
+#endif
+
+#define CONFIG_CI_UDC
+#define CONFIG_USBD_HS
+#define CONFIG_USB_GADGET_DUALSPEED
+
+#define CONFIG_USB_GADGET
+#define CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_USB_GADGET_MASS_STORAGE
+#define CONFIG_USBDOWNLOAD_GADGET
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+
+#define CONFIG_G_DNL_VENDOR_NUM 0x0525
+#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
+#define CONFIG_G_DNL_MANUFACTURER "FSL"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console=ttymxc0\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=imx6sl-warp.dtb\0" \
+ "fdt_addr=0x88000000\0" \
+ "initrd_addr=0x83800000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev=0\0" \
+ "mmcpart=1\0" \
+ "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev};" \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+#endif /* __CONFIG_H */
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index 313fa1e..57295b4 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -155,6 +155,8 @@
#define ESDHC_HOSTCAPBLT_DMAS 0x00400000
#define ESDHC_HOSTCAPBLT_HSS 0x00200000
+#define ESDHC_VENDORSPEC_VSELECT 0x00000002 /* Use 1.8V */
+
struct fsl_esdhc_cfg {
u32 esdhc_base;
u32 sdhc_clk;
diff --git a/include/fsl_sec.h b/include/fsl_sec.h
index b6e6f04..dbfae68 100644
--- a/include/fsl_sec.h
+++ b/include/fsl_sec.h
@@ -135,7 +135,7 @@
#define CONFIG_JRSTARTR_JR0 0x00000001
struct jr_regs {
-#ifdef CONFIG_SYS_FSL_SEC_LE
+#if defined(CONFIG_SYS_FSL_SEC_LE) && !defined(CONFIG_MX6)
u32 irba_l;
u32 irba_h;
#else
@@ -148,7 +148,7 @@
u32 irsa;
u32 rsvd3;
u32 irja;
-#ifdef CONFIG_SYS_FSL_SEC_LE
+#if defined(CONFIG_SYS_FSL_SEC_LE) && !defined(CONFIG_MX6)
u32 orba_l;
u32 orba_h;
#else
@@ -180,7 +180,7 @@
* related information
*/
struct sg_entry {
-#ifdef CONFIG_SYS_FSL_SEC_LE
+#ifdef defined(CONFIG_SYS_FSL_SEC_LE) && !defined(CONFIG_MX6)
uint32_t addr_lo; /* Memory Address - lo */
uint16_t addr_hi; /* Memory Address of start of buffer - hi */
uint16_t reserved_zero;
@@ -201,7 +201,79 @@
#define SG_ENTRY_OFFSET_SHIFT 0
};
+#ifdef CONFIG_MX6
+/* CAAM Job Ring 0 Registers */
+/* Secure Memory Partition Owner register */
+#define SMCSJR_PO (3 << 6)
+/* JR Allocation Error */
+#define SMCSJR_AERR (3 << 12)
+/* Secure memory partition 0 page 0 owner register */
+#define CAAM_SMPO_0 CONFIG_SYS_FSL_SEC_ADDR + 0x1FBC
+/* Secure memory command register */
+#define CAAM_SMCJR0 CONFIG_SYS_FSL_SEC_ADDR + 0x10f4
+/* Secure memory command status register */
+#define CAAM_SMCSJR0 CONFIG_SYS_FSL_SEC_ADDR + 0x10fc
+/* Secure memory access permissions register */
+#define CAAM_SMAPJR0(y) (CONFIG_SYS_FSL_SEC_ADDR + 0x1104 + y*16)
+/* Secure memory access group 2 register */
+#define CAAM_SMAG2JR0(y) (CONFIG_SYS_FSL_SEC_ADDR + 0x1108 + y*16)
+/* Secure memory access group 1 register */
+#define CAAM_SMAG1JR0(y) (CONFIG_SYS_FSL_SEC_ADDR + 0x110C + y*16)
+
+/* Commands and macros for secure memory */
+#define CMD_PAGE_ALLOC 0x1
+#define CMD_PAGE_DEALLOC 0x2
+#define CMD_PART_DEALLOC 0x3
+#define CMD_INQUIRY 0x5
+#define CMD_COMPLETE (3 << 14)
+#define PAGE_AVAILABLE 0
+#define PAGE_OWNED (3 << 6)
+#define PAGE(x) (x << 16)
+#define PARTITION(x) (x << 8)
+#define PARTITION_OWNER(x) (0x3 << (x*2))
+
+/* Address of secure 4kbyte pages */
+#define SEC_MEM_PAGE0 CAAM_ARB_BASE_ADDR
+#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
+#define SEC_MEM_PAGE2 (CAAM_ARB_BASE_ADDR + 0x2000)
+#define SEC_MEM_PAGE3 (CAAM_ARB_BASE_ADDR + 0x3000)
+
+#define JR_MID 2 /* Matches ROM configuration */
+#define KS_G1 (1 << JR_MID) /* CAAM only */
+#define PERM 0x0000B008 /* Clear on release, lock SMAP
+ * lock SMAG group 1 Blob */
+
+#define BLOB_SIZE(x) (x + 32 + 16) /* Blob buffer size */
+
+/* HAB WRAPPED KEY header */
+#define WRP_HDR_SIZE 0x08
+#define HDR_TAG 0x81
+#define HDR_PAR 0x41
+/* HAB WRAPPED KEY Data */
+#define HAB_MOD 0x66
+#define HAB_ALG 0x55
+#define HAB_FLG 0x00
+
+/* Partition and Page IDs */
+#define PARTITION_1 1
+#define PAGE_1 1
+
+#define ERROR_IN_PAGE_ALLOC 1
+#define ECONSTRJDESC -1
+
+#endif
+
int sec_init(void);
+
+/* blob_dek:
+ * Encapsulates the src in a secure blob and stores it dst
+ * @src: reference to the plaintext
+ * @dst: reference to the output adrress
+ * @len: size in bytes of src
+ * @return: 0 on success, error otherwise
+ */
+int blob_dek(const u8 *src, u8 *dst, u8 len);
+
#endif
#endif /* __FSL_SEC_H */
diff --git a/include/mc34704.h b/include/mc34704.h
index 53716e0..482d51a 100644
--- a/include/mc34704.h
+++ b/include/mc34704.h
@@ -40,6 +40,7 @@
/* GENERAL2 register fields */
#define ONOFFE (1 << 0)
#define ONOFFD (1 << 1)
+#define ONOFFA (1 << 3)
#define ALLOFF (1 << 4)
#endif /* __MC34704_H__ */
diff --git a/include/mmc.h b/include/mmc.h
index 7d6feca..2ad0f19 100644
--- a/include/mmc.h
+++ b/include/mmc.h
@@ -106,6 +106,7 @@
#define SD_CMD_SEND_RELATIVE_ADDR 3
#define SD_CMD_SWITCH_FUNC 6
#define SD_CMD_SEND_IF_COND 8
+#define SD_CMD_SWITCH_UHS18V 11
#define SD_CMD_APP_SET_BUS_WIDTH 6
#define SD_CMD_ERASE_WR_BLK_START 32
diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
index d304658..07199b4 100644
--- a/include/power/pfuze100_pmic.h
+++ b/include/power/pfuze100_pmic.h
@@ -232,5 +232,7 @@
#define APS_PFM 0xc
#define PWM_PFM 0xd
+#define SWITCH_SIZE 0x7
+
int power_pfuze100_init(unsigned char bus);
#endif