diff --git a/doc/device-tree-bindings/power/tps65090.txt b/doc/device-tree-bindings/power/tps65090.txt
new file mode 100644
index 0000000..8e5e0d3
--- /dev/null
+++ b/doc/device-tree-bindings/power/tps65090.txt
@@ -0,0 +1,17 @@
+TPS65090 Frontend PMU with Switchmode Charger
+
+Required Properties:
+-compatible: "ti,tps65090-charger"
+
+Optional Properties:
+-ti,enable-low-current-chrg: Enables charging when a low current is detected
+ while the default logic is to stop charging.
+
+This node is a subnode of the tps65090 PMIC.
+
+Example:
+
+	tps65090-charger {
+		compatible = "ti,tps65090-charger";
+		ti,enable-low-current-chrg;
+	};
diff --git a/doc/device-tree-bindings/regulator/tps65090.txt b/doc/device-tree-bindings/regulator/tps65090.txt
new file mode 100644
index 0000000..313a60b
--- /dev/null
+++ b/doc/device-tree-bindings/regulator/tps65090.txt
@@ -0,0 +1,122 @@
+TPS65090 regulators
+
+Required properties:
+- compatible: "ti,tps65090"
+- reg: I2C slave address
+- interrupts: the interrupt outputs of the controller
+- regulators: A node that houses a sub-node for each regulator within the
+  device. Each sub-node is identified using the node's name, with valid
+  values listed below. The content of each sub-node is defined by the
+  standard binding for regulators; see regulator.txt.
+  dcdc[1-3], fet[1-7] and ldo[1-2] respectively.
+- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively.
+- infet[1-7]-supply: The input supply for FET[1-7] respectively.
+- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively.
+
+Optional properties:
+- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
+  If DCDCs are externally controlled then this property should be there.
+- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+  If DCDCs are externally controlled and if it is from GPIO then GPIO
+  number should be provided. If it is externally controlled and no GPIO
+  entry then driver will just configure this rails as external control
+  and will not provide any enable/disable APIs.
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+	tps65090@48 {
+		compatible = "ti,tps65090";
+		reg = <0x48>;
+		interrupts = <0 88 0x4>;
+
+		vsys1-supply = <&some_reg>;
+		vsys2-supply = <&some_reg>;
+		vsys3-supply = <&some_reg>;
+		infet1-supply = <&some_reg>;
+		infet2-supply = <&some_reg>;
+		infet3-supply = <&some_reg>;
+		infet4-supply = <&some_reg>;
+		infet5-supply = <&some_reg>;
+		infet6-supply = <&some_reg>;
+		infet7-supply = <&some_reg>;
+		vsys_l1-supply = <&some_reg>;
+		vsys_l2-supply = <&some_reg>;
+
+		regulators {
+			dcdc1 {
+				regulator-name = "dcdc1";
+				regulator-boot-on;
+				regulator-always-on;
+				ti,enable-ext-control;
+				dcdc-ext-control-gpios = <&gpio 10 0>;
+			};
+
+			dcdc2 {
+				regulator-name = "dcdc2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			dcdc3 {
+				regulator-name = "dcdc3";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet1 {
+				regulator-name = "fet1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet2 {
+				regulator-name = "fet2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet3 {
+				regulator-name = "fet3";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet4 {
+				regulator-name = "fet4";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet5 {
+				regulator-name = "fet5";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet6 {
+				regulator-name = "fet6";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet7 {
+				regulator-name = "fet7";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1 {
+				regulator-name = "ldo1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2 {
+				regulator-name = "ldo2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile
index 4129bda..3244f69 100644
--- a/drivers/power/pmic/Makefile
+++ b/drivers/power/pmic/Makefile
@@ -10,5 +10,6 @@
 obj-$(CONFIG_POWER_MUIC_MAX8997) += muic_max8997.o
 obj-$(CONFIG_POWER_MAX77686) += pmic_max77686.o
 obj-$(CONFIG_POWER_PFUZE100) += pmic_pfuze100.o
+obj-$(CONFIG_POWER_TPS65090) += pmic_tps65090.o
 obj-$(CONFIG_POWER_TPS65217) += pmic_tps65217.o
 obj-$(CONFIG_POWER_TPS65910) += pmic_tps65910.o
diff --git a/drivers/power/pmic/pmic_tps65090.c b/drivers/power/pmic/pmic_tps65090.c
new file mode 100644
index 0000000..c5b3966
--- /dev/null
+++ b/drivers/power/pmic/pmic_tps65090.c
@@ -0,0 +1,310 @@
+/*
+ * Copyright (c) 2012 The Chromium OS Authors.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <i2c.h>
+#include <power/pmic.h>
+#include <power/tps65090_pmic.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define TPS65090_NAME "TPS65090_PMIC"
+
+/* TPS65090 register addresses */
+enum {
+	REG_IRQ1 = 0,
+	REG_CG_CTRL0 = 4,
+	REG_CG_STATUS1 = 0xa,
+	REG_FET1_CTRL = 0x0f,
+	REG_FET2_CTRL,
+	REG_FET3_CTRL,
+	REG_FET4_CTRL,
+	REG_FET5_CTRL,
+	REG_FET6_CTRL,
+	REG_FET7_CTRL,
+	TPS65090_NUM_REGS,
+};
+
+enum {
+	IRQ1_VBATG = 1 << 3,
+	CG_CTRL0_ENC_MASK	= 0x01,
+
+	MAX_FET_NUM	= 7,
+	MAX_CTRL_READ_TRIES = 5,
+
+	/* TPS65090 FET_CTRL register values */
+	FET_CTRL_TOFET		= 1 << 7,  /* Timeout, startup, overload */
+	FET_CTRL_PGFET		= 1 << 4,  /* Power good for FET status */
+	FET_CTRL_WAIT		= 3 << 2,  /* Overcurrent timeout max */
+	FET_CTRL_ADENFET	= 1 << 1,  /* Enable output auto discharge */
+	FET_CTRL_ENFET		= 1 << 0,  /* Enable FET */
+};
+
+/**
+ * Checks for a valid FET number
+ *
+ * @param fet_id	FET number to check
+ * @return 0 if ok, -EINVAL if FET value is out of range
+ */
+static int tps65090_check_fet(unsigned int fet_id)
+{
+	if (fet_id == 0 || fet_id > MAX_FET_NUM) {
+		debug("parameter fet_id is out of range, %u not in 1 ~ %u\n",
+		      fet_id, MAX_FET_NUM);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * Set the power state for a FET
+ *
+ * @param pmic		pmic structure for the tps65090
+ * @param fet_id	Fet number to set (1..MAX_FET_NUM)
+ * @param set		1 to power on FET, 0 to power off
+ * @return -EIO if we got a comms error, -EAGAIN if the FET failed to
+ * change state. If all is ok, returns 0.
+ */
+static int tps65090_fet_set(struct pmic *pmic, int fet_id, bool set)
+{
+	int retry;
+	u32 reg, value;
+
+	value = FET_CTRL_ADENFET | FET_CTRL_WAIT;
+	if (set)
+		value |= FET_CTRL_ENFET;
+
+	if (pmic_reg_write(pmic, REG_FET1_CTRL + fet_id - 1, value))
+		return -EIO;
+
+	/* Try reading until we get a result */
+	for (retry = 0; retry < MAX_CTRL_READ_TRIES; retry++) {
+		if (pmic_reg_read(pmic, REG_FET1_CTRL + fet_id - 1, &reg))
+			return -EIO;
+
+		/* Check that the fet went into the expected state */
+		if (!!(reg & FET_CTRL_PGFET) == set)
+			return 0;
+
+		/* If we got a timeout, there is no point in waiting longer */
+		if (reg & FET_CTRL_TOFET)
+			break;
+
+		mdelay(1);
+	}
+
+	debug("FET %d: Power good should have set to %d but reg=%#02x\n",
+	      fet_id, set, reg);
+	return -EAGAIN;
+}
+
+int tps65090_fet_enable(unsigned int fet_id)
+{
+	struct pmic *pmic;
+	ulong start;
+	int loops;
+	int ret;
+
+	ret = tps65090_check_fet(fet_id);
+	if (ret)
+		return ret;
+
+	pmic = pmic_get(TPS65090_NAME);
+	if (!pmic)
+		return -EACCES;
+
+	start = get_timer(0);
+	for (loops = 0;; loops++) {
+		ret = tps65090_fet_set(pmic, fet_id, true);
+		if (!ret)
+			break;
+
+		if (get_timer(start) > 100)
+			break;
+
+		/* Turn it off and try again until we time out */
+		tps65090_fet_set(pmic, fet_id, false);
+	}
+
+	if (ret)
+		debug("%s: FET%d failed to power on: time=%lums, loops=%d\n",
+		      __func__, fet_id, get_timer(start), loops);
+	else if (loops)
+		debug("%s: FET%d powered on after %lums, loops=%d\n",
+		      __func__, fet_id, get_timer(start), loops);
+
+	/*
+	 * Unfortunately, there are some conditions where the power
+	 * good bit will be 0, but the fet still comes up. One such
+	 * case occurs with the lcd backlight. We'll just return 0 here
+	 * and assume that the fet will eventually come up.
+	 */
+	if (ret == -EAGAIN)
+		ret = 0;
+
+	return ret;
+}
+
+int tps65090_fet_disable(unsigned int fet_id)
+{
+	struct pmic *pmic;
+	int ret;
+
+	ret = tps65090_check_fet(fet_id);
+	if (ret)
+		return ret;
+
+	pmic = pmic_get(TPS65090_NAME);
+	if (!pmic)
+		return -EACCES;
+	ret = tps65090_fet_set(pmic, fet_id, false);
+
+	return ret;
+}
+
+int tps65090_fet_is_enabled(unsigned int fet_id)
+{
+	struct pmic *pmic;
+	u32 reg;
+	int ret;
+
+	ret = tps65090_check_fet(fet_id);
+	if (ret)
+		return ret;
+
+	pmic = pmic_get(TPS65090_NAME);
+	if (!pmic)
+		return -ENODEV;
+	ret = pmic_reg_read(pmic, REG_FET1_CTRL + fet_id - 1, &reg);
+	if (ret) {
+		debug("fail to read FET%u_CTRL register over I2C", fet_id);
+		return -EIO;
+	}
+
+	return reg & FET_CTRL_ENFET;
+}
+
+int tps65090_get_charging(void)
+{
+	struct pmic *pmic;
+	u32 val;
+	int ret;
+
+	pmic = pmic_get(TPS65090_NAME);
+	if (!pmic)
+		return -EACCES;
+
+	ret = pmic_reg_read(pmic, REG_CG_CTRL0, &val);
+	if (ret)
+		return ret;
+
+	return !!(val & CG_CTRL0_ENC_MASK);
+}
+
+static int tps65090_charger_state(struct pmic *pmic, int state,
+				  int current)
+{
+	u32 val;
+	int ret;
+
+	ret = pmic_reg_read(pmic, REG_CG_CTRL0, &val);
+	if (!ret) {
+		if (state == PMIC_CHARGER_ENABLE)
+			val |= CG_CTRL0_ENC_MASK;
+		else
+			val &= ~CG_CTRL0_ENC_MASK;
+		ret = pmic_reg_write(pmic, REG_CG_CTRL0, val);
+	}
+	if (ret) {
+		debug("%s: Failed to read/write register\n", __func__);
+		return ret;
+	}
+
+	return 0;
+}
+
+int tps65090_get_status(void)
+{
+	struct pmic *pmic;
+	u32 val;
+	int ret;
+
+	pmic = pmic_get(TPS65090_NAME);
+	if (!pmic)
+		return -EACCES;
+
+	ret = pmic_reg_read(pmic, REG_CG_STATUS1, &val);
+	if (ret)
+		return ret;
+
+	return val;
+}
+
+static int tps65090_charger_bat_present(struct pmic *pmic)
+{
+	u32 val;
+	int ret;
+
+	ret = pmic_reg_read(pmic, REG_IRQ1, &val);
+	if (ret)
+		return ret;
+
+	return !!(val & IRQ1_VBATG);
+}
+
+static struct power_chrg power_chrg_pmic_ops = {
+	.chrg_bat_present = tps65090_charger_bat_present,
+	.chrg_state = tps65090_charger_state,
+};
+
+int tps65090_init(void)
+{
+	struct pmic *p;
+	int bus;
+	int addr;
+	const void *blob = gd->fdt_blob;
+	int node, parent;
+
+	node = fdtdec_next_compatible(blob, 0, COMPAT_TI_TPS65090);
+	if (node < 0) {
+		debug("PMIC: No node for PMIC Chip in device tree\n");
+		debug("node = %d\n", node);
+		return -ENODEV;
+	}
+
+	parent = fdt_parent_offset(blob, node);
+	if (parent < 0) {
+		debug("%s: Cannot find node parent\n", __func__);
+		return -EINVAL;
+	}
+
+	bus = i2c_get_bus_num_fdt(parent);
+	if (p->bus < 0) {
+		debug("%s: Cannot find I2C bus\n", __func__);
+		return -ENOENT;
+	}
+	addr = fdtdec_get_int(blob, node, "reg", TPS65090_I2C_ADDR);
+	p = pmic_alloc();
+	if (!p) {
+		printf("%s: POWER allocation error!\n", __func__);
+		return -ENOMEM;
+	}
+
+	p->name = TPS65090_NAME;
+	p->bus = bus;
+	p->interface = PMIC_I2C;
+	p->number_of_regs = TPS65090_NUM_REGS;
+	p->hw.i2c.addr = addr;
+	p->hw.i2c.tx_num = 1;
+	p->chrg = &power_chrg_pmic_ops;
+
+	puts("TPS65090 PMIC init\n");
+
+	return 0;
+}
diff --git a/include/fdtdec.h b/include/fdtdec.h
index 8c751fd..4b029d7 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -92,6 +92,7 @@
 	COMPAT_SAMSUNG_EXYNOS5_I2C,	/* Exynos5 High Speed I2C Controller */
 	COMPAT_SANDBOX_HOST_EMULATION,	/* Sandbox emulation of a function */
 	COMPAT_SANDBOX_LCD_SDL,		/* Sandbox LCD emulation with SDL */
+	COMPAT_TI_TPS65090,		/* Texas Instrument TPS65090 */
 
 	COMPAT_COUNT,
 };
diff --git a/include/power/tps65090_pmic.h b/include/power/tps65090_pmic.h
new file mode 100644
index 0000000..dcf99c9
--- /dev/null
+++ b/include/power/tps65090_pmic.h
@@ -0,0 +1,73 @@
+/*
+ * Copyright (c) 2012 The Chromium OS Authors.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __TPS65090_PMIC_H_
+#define __TPS65090_PMIC_H_
+
+/* I2C device address for TPS65090 PMU */
+#define TPS65090_I2C_ADDR	0x48
+
+enum {
+	/* Status register fields */
+	TPS65090_ST1_OTC	= 1 << 0,
+	TPS65090_ST1_OCC	= 1 << 1,
+	TPS65090_ST1_STATE_SHIFT = 4,
+	TPS65090_ST1_STATE_MASK	= 0xf << TPS65090_ST1_STATE_SHIFT,
+};
+
+/**
+ * Enable FET
+ *
+ * @param	fet_id	FET ID, value between 1 and 7
+ * @return	0 on success, non-0 on failure
+ */
+int tps65090_fet_enable(unsigned int fet_id);
+
+/**
+ * Disable FET
+ *
+ * @param	fet_id	FET ID, value between 1 and 7
+ * @return	0 on success, non-0 on failure
+ */
+int tps65090_fet_disable(unsigned int fet_id);
+
+/**
+ * Is FET enabled?
+ *
+ * @param	fet_id	FET ID, value between 1 and 7
+ * @return	1 enabled, 0 disabled, negative value on failure
+ */
+int tps65090_fet_is_enabled(unsigned int fet_id);
+
+/**
+ * Enable / disable the battery charger
+ *
+ * @param enable	0 to disable charging, non-zero to enable
+ */
+int tps65090_set_charge_enable(int enable);
+
+/**
+ * Check whether we have enabled battery charging
+ *
+ * @return 1 if enabled, 0 if disabled
+ */
+int tps65090_get_charging(void);
+
+/**
+ * Return the value of the status register
+ *
+ * @return status register value, or -1 on error
+ */
+int tps65090_get_status(void);
+
+/**
+ * Initialize the TPS65090 PMU.
+ *
+ * @return	0 on success, non-0 on failure
+ */
+int tps65090_init(void);
+
+#endif /* __TPS65090_PMIC_H_ */
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index 35e91b4..6cccfe5 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -66,6 +66,7 @@
 	COMPAT(SAMSUNG_EXYNOS5_I2C, "samsung,exynos5-hsi2c"),
 	COMPAT(SANDBOX_HOST_EMULATION, "sandbox,host-emulation"),
 	COMPAT(SANDBOX_LCD_SDL, "sandbox,lcd-sdl"),
+	COMPAT(TI_TPS65090, "ti,tps65090"),
 };
 
 const char *fdtdec_get_compatible(enum fdt_compat_id id)