diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
index 69368d8..e672d8c 100644
--- a/board/mbx8xx/pcmcia.c
+++ b/board/mbx8xx/pcmcia.c
@@ -117,11 +117,7 @@
 	debug ("[%d] %s: PIPR(%p)=0x%x\n",
 	       __LINE__,__FUNCTION__,
 	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-#ifndef CONFIG_HMI10
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-#else
 	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-#endif	/* CONFIG_HMI10 */
 		printf ("   No Card found\n");
 		return (1);
 	}
diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c
index cde780b..940cc8f 100644
--- a/board/tqc/tqm8xx/tqm8xx.c
+++ b/board/tqc/tqm8xx/tqm8xx.c
@@ -430,29 +430,6 @@
 
 /* ------------------------------------------------------------------------- */
 
-#ifdef CONFIG_PS2MULT
-
-#ifdef CONFIG_HMI10
-#define BASE_BAUD ( 1843200 / 16 )
-struct serial_state rs_table[] = {
-	{ BASE_BAUD, 4,  (void*)0xec140000 },
-	{ BASE_BAUD, 2,  (void*)0xec150000 },
-	{ BASE_BAUD, 6,  (void*)0xec160000 },
-	{ BASE_BAUD, 10, (void*)0xec170000 },
-};
-
-#ifdef CONFIG_BOARD_EARLY_INIT_R
-int board_early_init_r (void)
-{
-	ps2mult_early_init();
-	return (0);
-}
-#endif
-#endif /* CONFIG_HMI10 */
-
-#endif /* CONFIG_PS2MULT */
-
-
 #ifdef CONFIG_MISC_INIT_R
 extern void load_sernum_ethaddr(void);
 int misc_init_r (void)
diff --git a/boards.cfg b/boards.cfg
index 0bf9c93..0fe1c89 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -104,8 +104,6 @@
 v38b		powerpc	mpc5xxx
 pf5200		powerpc	mpc5xxx		-		esd
 aev		powerpc	mpc5xxx		tqm5200		tqc
-smmaco4		powerpc	mpc5xxx		tqm5200		tqc
-spieval		powerpc	mpc5xxx		tqm5200		tqc
 sorcery		powerpc	mpc8220
 A3000		powerpc	mpc824x		a3000
 barco		powerpc	mpc824x
@@ -170,7 +168,6 @@
 QS850		powerpc	mpc8xx		qs850		snmc
 QS860T		powerpc	mpc8xx		qs860t		snmc
 stxxtc		powerpc	mpc8xx		stxxtc		stx
-HMI10		powerpc	mpc8xx		tqm8xx		tqc
 SM850		powerpc	mpc8xx		tqm8xx		tqc
 AMX860		powerpc	mpc8xx		amx860		westel
 csb272		powerpc	ppc4xx
diff --git a/common/cmd_ide.c b/common/cmd_ide.c
index 6aeca76..ea0f4a7 100644
--- a/common/cmd_ide.c
+++ b/common/cmd_ide.c
@@ -818,7 +818,7 @@
 static void
 input_swap_data(int dev, ulong *sect_buf, int words)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar i;
 	volatile uchar *pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
 	volatile uchar *pbuf_odd  = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
@@ -858,7 +858,7 @@
 static void
 output_data(int dev, ulong *sect_buf, int words)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
@@ -910,7 +910,7 @@
 static void
 input_data(int dev, ulong *sect_buf, int words)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
@@ -1544,7 +1544,6 @@
 
 #if defined(CONFIG_IDE_LED)	&& \
    !defined(CONFIG_CPC45)	&& \
-   !defined(CONFIG_HMI10)	&& \
    !defined(CONFIG_KUP4K)	&& \
    !defined(CONFIG_KUP4X)
 
@@ -1586,7 +1585,7 @@
 static void
 output_data_shorts(int dev, ushort *sect_buf, int shorts)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
@@ -1618,7 +1617,7 @@
 static void
 input_data_shorts(int dev, ushort *sect_buf, int shorts)
 {
-#if defined(CONFIG_HMI10) || defined(CONFIG_CPC45)
+#if defined(CONFIG_CPC45)
 	uchar	*dbuf;
 	volatile uchar	*pbuf_even;
 	volatile uchar	*pbuf_odd;
diff --git a/drivers/input/ps2ser.c b/drivers/input/ps2ser.c
index 8d0b6d6..a655a16 100644
--- a/drivers/input/ps2ser.c
+++ b/drivers/input/ps2ser.c
@@ -46,8 +46,7 @@
 #error CONFIG_PS2SERIAL must be in 1 ... 6
 #endif
 
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 
 #if CONFIG_PS2SERIAL == 1
 #define COM_BASE (CONFIG_SYS_CCSRBAR+0x4500)
@@ -57,17 +56,12 @@
 #error CONFIG_PS2SERIAL must be in 1 ... 2
 #endif
 
-#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */
+#endif /* CONFIG_MPC5xxx / other */
 
 static int	ps2ser_getc_hw(void);
 static void	ps2ser_interrupt(void *dev_id);
 
 extern struct	serial_state rs_table[]; /* in serial.c */
-#if !defined(CONFIG_MPC5xxx) && !defined(CONFIG_MPC8540) && \
-    !defined(CONFIG_MPC8541) && !defined(CONFIG_MPC8548) && \
-    !defined(CONFIG_MPC8555)
-static struct	serial_state *state;
-#endif
 
 static u_char	ps2buf[PS2BUF_SIZE];
 static atomic_t	ps2buf_cnt;
@@ -111,8 +105,8 @@
 	return (0);
 }
 
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
+
 int ps2ser_init(void)
 {
 	NS16550_t com_port = (NS16550_t)COM_BASE;
@@ -128,76 +122,24 @@
 	return (0);
 }
 
-#else /* !CONFIG_MPC5xxx && !CONFIG_MPC8540 / other */
-
-static inline unsigned int ps2ser_in(int offset)
-{
-	return readb((unsigned long) state->iomem_base + offset);
-}
-
-static inline void ps2ser_out(int offset, int value)
-{
-	writeb(value, (unsigned long) state->iomem_base + offset);
-}
-
-int ps2ser_init(void)
-{
-	int quot;
-	unsigned cval;
-
-	state = rs_table + CONFIG_PS2SERIAL;
-
-	quot = state->baud_base / PS2SER_BAUD;
-	cval = 0x3; /* 8N1 - 8 data bits, no parity bits, 1 stop bit */
-
-	  /* Set speed, enable interrupts, enable FIFO
-	   */
-	ps2ser_out(UART_LCR, cval | UART_LCR_DLAB);
-	ps2ser_out(UART_DLL, quot & 0xff);
-	ps2ser_out(UART_DLM, quot >> 8);
-	ps2ser_out(UART_LCR, cval);
-	ps2ser_out(UART_IER, UART_IER_RDI);
-	ps2ser_out(UART_MCR, UART_MCR_OUT2 | UART_MCR_DTR | UART_MCR_RTS);
-	ps2ser_out(UART_FCR,
-	    UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
-
-	/* If we read 0xff from the LSR, there is no UART here
-	 */
-	if (ps2ser_in(UART_LSR) == 0xff) {
-		printf ("ps2ser.c: no UART found\n");
-		return -1;
-	}
-
-	irq_install_handler(state->irq, ps2ser_interrupt, NULL);
-
-	return 0;
-}
-#endif /* CONFIG_MPC5xxx / CONFIG_MPC8540 / other */
+#endif /* CONFIG_MPC5xxx / other */
 
 void ps2ser_putc(int chr)
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
-#ifdef DEBUG
-	printf(">>>> 0x%02x\n", chr);
-#endif
+	debug(">>>> 0x%02x\n", chr);
 
 #ifdef CONFIG_MPC5xxx
 	while (!(psc->psc_status & PSC_SR_TXRDY));
 
 	psc->psc_buffer_8 = chr;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	while ((com_port->lsr & UART_LSR_THRE) == 0);
 	com_port->thr = chr;
-#else
-	while (!(ps2ser_in(UART_LSR) & UART_LSR_THRE));
-
-	ps2ser_out(UART_TX, chr);
 #endif
 }
 
@@ -205,8 +147,7 @@
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 	int res = -1;
@@ -215,15 +156,10 @@
 	if (psc->psc_status & PSC_SR_RXRDY) {
 		res = (psc->psc_buffer_8);
 	}
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	if (com_port->lsr & UART_LSR_DR) {
 		res = com_port->rbr;
 	}
-#else
-	if (ps2ser_in(UART_LSR) & UART_LSR_DR) {
-		res = (ps2ser_in(UART_RX));
-	}
 #endif
 
 	return res;
@@ -234,9 +170,7 @@
 	volatile int chr;
 	int flags;
 
-#ifdef DEBUG
-	printf("<< ");
-#endif
+	debug("<< ");
 
 	flags = disable_interrupts();
 
@@ -251,11 +185,10 @@
 	}
 	while (chr < 0);
 
-	if (flags) enable_interrupts();
+	if (flags)
+		enable_interrupts();
 
-#ifdef DEBUG
-	printf("0x%02x\n", chr);
-#endif
+	debug("0x%02x\n", chr);
 
 	return chr;
 }
@@ -275,8 +208,7 @@
 {
 #ifdef CONFIG_MPC5xxx
 	volatile struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)PSC_BASE;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
+#else
 	NS16550_t com_port = (NS16550_t)COM_BASE;
 #endif
 	int chr;
@@ -286,11 +218,8 @@
 		chr = ps2ser_getc_hw();
 #ifdef CONFIG_MPC5xxx
 		status = psc->psc_status;
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
-		status = com_port->lsr;
 #else
-		status = ps2ser_in(UART_IIR);
+		status = com_port->lsr;
 #endif
 		if (chr < 0) continue;
 
@@ -303,13 +232,9 @@
 		}
 #ifdef CONFIG_MPC5xxx
 	} while (status & PSC_SR_RXRDY);
-#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
-      defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
-	} while (status & UART_LSR_DR);
 #else
-	} while (status & UART_IIR_RDI);
+	} while (status & UART_LSR_DR);
 #endif
-
 	if (atomic_read(&ps2buf_cnt)) {
 		ps2mult_callback(atomic_read(&ps2buf_cnt));
 	}
diff --git a/drivers/pcmcia/mpc8xx_pcmcia.c b/drivers/pcmcia/mpc8xx_pcmcia.c
index 7030574..74a50f1 100644
--- a/drivers/pcmcia/mpc8xx_pcmcia.c
+++ b/drivers/pcmcia/mpc8xx_pcmcia.c
@@ -57,12 +57,6 @@
 
 /* -------------------------------------------------------------------- */
 
-#ifdef	CONFIG_HMI10
-#define	HMI10_FRAM_TIMING	(	PCMCIA_SHT(2)	\
-				|	PCMCIA_SST(2)	\
-				|	PCMCIA_SL(4))
-#endif
-
 #if	defined(CONFIG_LWMON) || defined(CONFIG_NSCU)
 #define	CONFIG_SYS_PCMCIA_TIMING	(	PCMCIA_SHT(9)	\
 				|	PCMCIA_SST(3)	\
@@ -106,17 +100,6 @@
 		switch (i) {
 #ifdef	CONFIG_IDE_8xx_PCCARD
 		case 4:
-#ifdef	CONFIG_HMI10
-		{	/* map FRAM area */
-			win->or = (	PCMCIA_BSIZE_256K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_ATTR
-				|	slotbit
-				|	PCMCIA_PV
-				|	HMI10_FRAM_TIMING );
-			break;
-		}
-#endif
 		case 0:	{	/* map attribute memory */
 			win->or = (	PCMCIA_BSIZE_64M
 				|	PCMCIA_PPS_8
@@ -147,18 +130,6 @@
 			break;
 		}
 #endif	/* CONFIG_IDE_8xx_PCCARD */
-#ifdef	CONFIG_HMI10
-		case 3: {	/* map I/O window for 4xUART data/ctrl */
-			win->br += 0x40000;
-			win->or = (	PCMCIA_BSIZE_256K
-				|	PCMCIA_PPS_8
-				|	PCMCIA_PRS_IO
-				|	slotbit
-				|	PCMCIA_PV
-				|	CONFIG_SYS_PCMCIA_TIMING );
-			break;
-		}
-#endif	/* CONFIG_HMI10 */
 		default:	/* set to not valid */
 			win->or = 0;
 			break;
diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c
index 6ba8b5c..ca1a9fe 100644
--- a/drivers/pcmcia/tqm8xx_pcmcia.c
+++ b/drivers/pcmcia/tqm8xx_pcmcia.c
@@ -36,39 +36,6 @@
 #define	power_on_5_0(slot)	do {} while (0)
 #define	power_on_3_3(slot)	do {} while (0)
 
-#elif	defined(CONFIG_HMI10)
-
-static inline void power_config(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	/*
-	 * Configure Port B  pins for
-	 * 5 Volts Enable and 3 Volts enable
-	*/
-	immap->im_cpm.cp_pbpar &= ~(0x00000300);
-}
-
-static inline void power_off(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	/* remove all power */
-	immap->im_cpm.cp_pbdat |= 0x00000300;
-}
-
-static inline void power_on_5_0(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	immap->im_cpm.cp_pbdat &= ~(0x0000100);
-	immap->im_cpm.cp_pbdir |= 0x00000300;
-}
-
-static inline void power_on_3_3(int slot)
-{
-	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
-	immap->im_cpm.cp_pbdat &= ~(0x0000200);
-	immap->im_cpm.cp_pbdir |= 0x00000300;
-}
-
 #elif	defined(CONFIG_VIRTLAB2)
 
 #define	power_config(slot)	do {} while (0)
@@ -128,21 +95,12 @@
 
 #endif
 
-#ifdef	CONFIG_HMI10
-static inline int check_card_is_absent(int slot)
-{
-	volatile pcmconf8xx_t *pcmp =
-		(pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-	return pcmp->pcmc_pipr & (0x10000000 >> (slot << 4));
-}
-#else
 static inline int check_card_is_absent(int slot)
 {
 	volatile pcmconf8xx_t *pcmp =
 		(pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
 	return pcmp->pcmc_pipr & (0x18000000 >> (slot << 4));
 }
-#endif
 
 #ifdef	NSCU_OE_INV
 #define	NSCU_GCRX_CXOE	0
diff --git a/include/configs/HMI10.h b/include/configs/HMI10.h
deleted file mode 100644
index 2747d8c..0000000
--- a/include/configs/HMI10.h
+++ /dev/null
@@ -1,504 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_HMI10
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_TQM823L		1	/* ...on a TQM8xxL module	*/
-
-#define CONFIG_LCD
-#define CONFIG_NEC_NL6448BC33_54	/* NEC NL6448BC33_54 display	*/
-
-#ifdef	CONFIG_LCD			/* with LCD controller ?	*/
-#define CONFIG_SPLASH_SCREEN		/* ... with splashscreen support*/
-#endif
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
-
-#define CONFIG_PS2KBD			/* AT-PS/2 Keyboard		*/
-#define CONFIG_PS2MULT			/* .. on PS/2 Multiplexer	*/
-#define CONFIG_PS2SERIAL	2	/* .. on COM3			*/
-#define CONFIG_PS2MULT_DELAY	(CONFIG_SYS_HZ/2)	/* Initial delay	*/
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_8xx\0"					\
-	"bootfile=/tftpboot/HMI10/uImage\0"				\
-	"kernel_addr=40040000\0"					\
-	"ramdisk_addr=40100000\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define	CONFIG_BOARD_EARLY_INIT_R 1
-#define CONFIG_MISC_INIT_R	  1
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-/* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		40000	/* 40 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-/* Software (bit-bang) I2C driver configuration */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
-#define CONFIG_CAN_DRIVER	1	/* CAN Driver support enabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_DS1337		/* Use ds1337 rtc via i2c	*/
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68		/* at address 0x68		*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-#ifdef	CONFIG_SPLASH_SCREEN
-    #define CONFIG_CMD_BMP
-#endif
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt	*/
-
-#if 0
-#define CONFIG_SYS_HUSH_PARSER		1	/* use "hush" command parser	*/
-#endif
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size	  of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else	/* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0100000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4100000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8100000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC100000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-#define PCMCIA_MEM_WIN_NO	5
-#define NSCU_OE_INV		1		/* PCMCIA_GCRX_CXOE is inverted */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-#ifndef CONFIG_STATUS_LED		/* Status and IDE LED's are mutually exclusive */
-#define CONFIG_IDE_LED		1	/* LED   for ide supported	*/
-#endif
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-					BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif	/* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096	 Rows from SDRAM example configuration
- * 1000	 factor s -> ms
- *   32	 PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4	 Number of refresh cycles per period
- *   64	 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA	98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-#define CONFIG_HWCONFIG		1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h
deleted file mode 100644
index 060026b..0000000
--- a/include/configs/smmaco4.h
+++ /dev/null
@@ -1,379 +0,0 @@
-/*
- * (C) Copyright 2003-2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004-2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5xxx		1	/* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200		1	/* (more precisely an MPC5200 CPU) */
-#define CONFIG_TQM5200		1	/* ... on TQM5200 module */
-#undef CONFIG_TQM5200_REV100		/*  define for revision 100 modules */
-
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
-
-#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM		0x02	/* Software reboot	     */
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/* POST support */
-#define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
-				 CONFIG_SYS_POST_CPU	   | \
-				 CONFIG_SYS_POST_I2C)
-
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SNTP
-
-#ifdef CONFIG_POST
-#define CONFIG_CMD_DIAG
-#endif
-
-
-#define	CONFIG_TIMESTAMP		/* display image timestamps */
-
-#if (TEXT_BASE == 0xFC000000)		/* Boot low */
-#   define CONFIG_SYS_LOWBOOT		1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"rootpath=/opt/eldk/ppc_6xx\0"					\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"bootfile=/tftpboot/smmaco4/uImage\0"				\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"u-boot=/tftpboot/smmaco4/u-boot.bin\0"				\
-	"update=protect off FC000000 FC05FFFF;"				\
-		"erase FC000000 FC05FFFF;"				\
-		"cp.b 200000 FC000000 ${filesize};"			\
-		"protect on FC000000 FC05FFFF\0"			\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-
-#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
-/*
- * PCI Bus clocking configuration
- *
- * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
- * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
- */
-#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
-#endif
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE		TEXT_BASE /* 0xFC000000 */
-
-/* use CFI flash driver if no module variant is spezified */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_BOOTCS_START }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_SIZE		0x04000000 /* 64 MByte */
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
-#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* not supported yet for AMD */
-
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
-#else	/* CONFIG_SYS_LOWBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00060000)
-#endif	/* CONFIG_SYS_LOWBOOT */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
-					   (= chip selects) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
-
-/* Dynamic MTD partition support */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=TQM5200-0"
-#define MTDPARTS_DEFAULT	"mtdparts=TQM5200-0:640k(firmware),"	\
-						"1408k(kernel),"	\
-						"2m(initrd),"		\
-						"4m(small-fs),"		\
-						"16m(big-fs),"		\
-						"8m(misc)"
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x10000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define	CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR		0xF0000000
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_POST_SIZE
-#else
-#define CONFIG_SYS_INIT_RAM_END	MPC5XXX_SRAM_SIZE
-#endif
-
-
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(384 << 10)	/* Reserve 384 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC	1
-/*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
- */
-/* #define CONFIG_FEC_10MBIT 1 */
-#define CONFIG_PHY_ADDR		0x00
-
-/*
- * GPIO configuration
- *
- * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
- *	Bit 0 (mask: 0x80000000): 1
- * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
- *	00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
- *	01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
- *	      Use for REV200 STK52XX boards. Do not use with REV100 modules
- *	      (because, there I2C1 is used as I2C bus)
- * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
- * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
- *	000 -> All PSC2 pins are GIOPs
- *	001 -> CAN1/2 on PSC2 pins
- *	       Use for REV100 STK52xx boards
- * use PSC6:
- *   on STK52xx:
- *	use as UART. Pins PSC6_0 to PSC6_3 are used.
- *	Bits 9:11 (mask: 0x00700000):
- *	   101 -> PSC6 : Extended POST test is not available
- *   on MINI-FAP and TQM5200_IB:
- *	use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
- *	   000 -> PSC6 could not be used as UART, CODEC or IrDA
- *   GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- *   tests.
- */
-#if defined (CONFIG_MINIFAP)
-# define CONFIG_SYS_GPS_PORT_CONFIG	0x91000004
-#elif defined (CONFIG_STK52XX)
-# if defined (CONFIG_STK52XX_REV100)
-#  define CONFIG_SYS_GPS_PORT_CONFIG	0x81500014
-# else /* STK52xx REV200 and above */
-#  if defined (CONFIG_TQM5200_REV100)
-#   error TQM5200 REV100 not supported on STK52XX REV200 or above
-#  else/* TQM5200 REV200 and above */
-#   define CONFIG_SYS_GPS_PORT_CONFIG	0x91500004
-#  endif
-# endif
-#else  /* TMQ5200 Inbetriebnahme-Board */
-# define CONFIG_SYS_GPS_PORT_CONFIG	0x81000004
-#endif
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt   */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-/* Enable an alternate, more extensive memory test */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
-#define CONFIG_SYS_BOOTCS_CFG		0x0008DF30 /* for pci_clk  = 66 MHz */
-#else
-#define CONFIG_SYS_BOOTCS_CFG		0x0004DF30 /* for pci_clk = 33 MHz */
-#endif
-#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS_BURST		0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE	0x33333311	/* 1 dead cycle for flash and SM501 */
-
-#define CONFIG_SYS_RESET_ADDRESS	0xff000000
-
-#endif /* __CONFIG_H */
diff --git a/include/status_led.h b/include/status_led.h
index f213595..b39ca64 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -43,7 +43,7 @@
 void status_led_set  (int led, int state);
 
 /*****  TQM8xxL  ********************************************************/
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_HMI10)
+#if defined(CONFIG_TQM8xxL)
 # define STATUS_LED_PAR		im_cpm.cp_pbpar
 # define STATUS_LED_DIR		im_cpm.cp_pbdir
 # define STATUS_LED_ODR		im_cpm.cp_pbodr
@@ -318,21 +318,6 @@
 
 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 
-/*****  HMI10  **********************************************************/
-#elif defined(CONFIG_HMI10)
-# define STATUS_LED_PAR		im_ioport.iop_papar
-# define STATUS_LED_DIR		im_ioport.iop_padir
-# define STATUS_LED_ODR		im_ioport.iop_paodr
-# define STATUS_LED_DAT		im_ioport.iop_padat
-
-# define STATUS_LED_BIT		0x00000001	/* LED is on PA15 */
-# define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE	STATUS_LED_BLINKING
-
-# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
-
-# define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
-
 /*****  NetPhone   ********************************************************/
 #elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
 /* XXX empty just to avoid the error */