diff --git a/CHANGELOG b/CHANGELOG
index beff987..62d8a09 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,9 @@
 Changes for U-Boot 1.1.3:
 ======================================================================
 
+* Add NAND FLASH support for AMCC Bamboo 440EP eval board
+  Patch by Stefan Roese, 11 Aug 2005
+
 * Fix CompactFlash problem on HMI1001 board
 
 * Make new "mtdparts" code build with older compilers
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 0d5ab71..d02add5 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -29,6 +29,7 @@
 
 void ext_bus_cntlr_init(void);
 void configure_ppc440ep_pins(void);
+int is_nand_selected(void);
 
 gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX];
 #if 0
@@ -132,10 +133,10 @@
 	EBC0_BNCR_BW_8BIT
 
 #define EBC0_BNCR_SMALL_FLASH_CS4			\
-	EBC0_BNCR_BAS_ENCODE(0x87800000)    	| 	\
-	EBC0_BNCR_BS_8MB		    	|	\
+	EBC0_BNCR_BAS_ENCODE(0x87F00000)    	| 	\
+	EBC0_BNCR_BS_1MB		    	|	\
 	EBC0_BNCR_BU_RW			    	|	\
-	EBC0_BNCR_BW_16BIT
+	EBC0_BNCR_BW_8BIT
 
 /* Large Flash or SRAM */
 #define EBC0_BNAP_LARGE_FLASH_OR_SRAM			\
@@ -273,6 +274,87 @@
 	return 0;
 }
 
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
+
+/*----------------------------------------------------------------------------+
+  | nand_reset.
+  |   Reset Nand flash
+  |   This routine will abort previous cmd
+  +----------------------------------------------------------------------------*/
+int nand_reset(ulong addr)
+{
+	int wait=0, stat=0;
+
+	out8(addr + NAND_CMD_REG, NAND0_CMD_RESET);
+	out8(addr + NAND_CMD_REG, NAND0_CMD_READ_STATUS);
+
+	while ((stat != 0xc0) && (wait != 0xffff)) {
+		stat = in8(addr + NAND_DATA_REG);
+		wait++;
+	}
+
+	if (stat == 0xc0) {
+		return 0;
+	} else {
+		printf("NAND Reset timeout.\n");
+		return -1;
+	}
+}
+
+void board_nand_set_device(int cs, ulong addr)
+{
+	/* Set NandFlash Core Configuration Register */
+	out32(addr + NAND_CCR_REG, 0x00001000 | (cs << 24));
+
+	switch (cs) {
+	case 1:
+		/* -------
+		 *  NAND0
+		 * -------
+		 * K9F1208U0A : 4 addr cyc, 1 col + 3 Row
+		 * Set NDF1CR - Enable External CS1 in NAND FLASH controller
+		 */
+		out32(addr + NAND_CR1_REG, 0x80002222);
+		break;
+
+	case 2:
+		/* -------
+		 *  NAND1
+		 * -------
+		 * K9K2G0B : 5 addr cyc, 2 col + 3 Row
+		 * Set NDF2CR : Enable External CS2 in NAND FLASH controller
+		 */
+		out32(addr + NAND_CR2_REG, 0xC0007777);
+		break;
+	}
+
+	/* Perform Reset Command */
+	if (nand_reset(addr) != 0)
+		return;
+}
+
+void nand_init(void)
+{
+	board_nand_set_device(1, CFG_NAND_ADDR);
+
+	nand_probe(CFG_NAND_ADDR);
+	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
+		print_size(nand_dev_desc[0].totlen, "\n");
+	}
+
+#if 0 /* NAND1 not supported yet */
+	board_nand_set_device(2, CFG_NAND2_ADDR);
+
+	nand_probe(CFG_NAND2_ADDR);
+	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
+		print_size(nand_dev_desc[0].totlen, "\n");
+	}
+#endif
+}
+#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */
+
 int checkboard(void)
 {
 	sys_info_t sysinfo;
@@ -585,7 +667,11 @@
   +----------------------------------------------------------------------------*/
 int is_nand_selected(void)
 {
-	return FALSE; /* test-only */
+#ifdef CONFIG_BAMBOO_NAND
+	return TRUE;
+#else
+	return FALSE;
+#endif
 }
 
 /*----------------------------------------------------------------------------+
@@ -829,12 +915,8 @@
 			/* NAND Flash */
 			ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
 			ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
-			/*ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH;
-			  ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2;
-			  ebc0_cs3_bnap_value = EBC0_BNAP_NAND_FLASH;
-			  ebc0_cs3_bncr_value = EBC0_BNCR_NAND_FLASH_CS3;*/
-			ebc0_cs2_bnap_value = 0;
-			ebc0_cs2_bncr_value = 0;
+			ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH;
+			ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2;
 			ebc0_cs3_bnap_value = 0;
 			ebc0_cs3_bncr_value = 0;
 		} else {
@@ -985,7 +1067,7 @@
   +----------------------------------------------------------------------------*/
 uart_config_nb_t get_uart_configuration(void)
 {
-	return (L4); /* test-only */
+	return (L4);
 }
 
 /*----------------------------------------------------------------------------+
@@ -1132,8 +1214,7 @@
 
 	fpga_selection_1_reg  = in8(FPGA_SELECTION_1_REG) &~FPGA_SEL_1_REG_NF_SELEC_MASK;
 	fpga_selection_1_reg |= FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1;
-	/*fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2; */
-	/*fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS3; */
+	fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2;
 	out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
 }
 
@@ -1725,11 +1806,15 @@
 	*(core_select_P+UIC_0_3)		= CORE_SELECTED;
 	*(core_select_P+UIC_4_9)		= CORE_SELECTED;
 
-	*(core_select_P+SCP_CORE)	     = CORE_SELECTED;
-	*(core_select_P+DMA_CHANNEL_CD)		   = CORE_SELECTED;
-	*(core_select_P+PACKET_REJ_FUNC_AVAIL)		  = CORE_SELECTED;
+	*(core_select_P+SCP_CORE)	        = CORE_SELECTED;
+	*(core_select_P+DMA_CHANNEL_CD)		= CORE_SELECTED;
+	*(core_select_P+PACKET_REJ_FUNC_AVAIL)	= CORE_SELECTED;
 	*(core_select_P+USB1_DEVICE)		= CORE_SELECTED;
 
+	if (is_nand_selected()) {
+		*(core_select_P+NAND_FLASH)	= CORE_SELECTED;
+	}
+
 	*config_val_P = CONFIG_IS_VALID;
 
 }
@@ -1901,9 +1986,8 @@
 		      SDR0_CUST0_NDFC_ENABLE	|
 		      SDR0_CUST0_NDFC_BW_8_BIT	|
 		      SDR0_CUST0_NDFC_ARE_MASK	|
-		      SDR0_CUST0_CHIPSELGAT_EN1 );
-		/*SDR0_CUST0_CHIPSELGAT_EN2 ); */
-		/*SDR0_CUST0_CHIPSELGAT_EN3 ); */
+		      SDR0_CUST0_CHIPSELGAT_EN1 |
+		      SDR0_CUST0_CHIPSELGAT_EN2);
 
 		ndfc_selection_in_fpga();
 	}
diff --git a/board/amcc/bamboo/flash.c b/board/amcc/bamboo/flash.c
index 97a4b98..a30ab7a 100644
--- a/board/amcc/bamboo/flash.c
+++ b/board/amcc/bamboo/flash.c
@@ -50,15 +50,16 @@
 /*
  * Mark big flash bank (16 bit instead of 8 bit access) in address with bit 0
  */
-static unsigned long flash_addr_table[8][CFG_MAX_FLASH_BANKS] = {
+static unsigned long flash_addr_table[][CFG_MAX_FLASH_BANKS] = {
 	{0x87800001, 0xFFF00000, 0xFFF80000}, /* 0:boot from small flash */
 	{0x00000000, 0x00000000, 0x00000000}, /* 1:boot from pci 66      */
 	{0x00000000, 0x00000000, 0x00000000}, /* 2:boot from nand flash  */
-	{0x87800000, 0x87880000, 0xFF800001}, /* 3:boot from big flash 33*/
-	{0x87800000, 0x87880000, 0xFF800001}, /* 4:boot from big flash 66*/
+	{0x87F00000, 0x87F80000, 0xFFC00001}, /* 3:boot from big flash 33*/
+	{0x87F00000, 0x87F80000, 0xFFC00001}, /* 4:boot from big flash 66*/
 	{0x00000000, 0x00000000, 0x00000000}, /* 5:boot from             */
 	{0x00000000, 0x00000000, 0x00000000}, /* 6:boot from pci 66      */
 	{0x00000000, 0x00000000, 0x00000000}, /* 7:boot from             */
+	{0x87C00001, 0xFFF00000, 0xFFF80000}, /* 0:boot from small flash */
 };
 
 /*
@@ -117,6 +118,10 @@
 			index = 2;
 			break;
 		}
+	} else if (index == 0) {
+		if (in8(FPGA_SETTING_REG) & FPGA_SET_REG_OP_CODE_FLASH_ABOVE) {
+			index = 8; /* sram below op code flash -> new index 8 */
+		}
 	}
 
 	DEBUGF("\n");
diff --git a/board/amcc/bamboo/init.S b/board/amcc/bamboo/init.S
index 9070293..7820107 100644
--- a/board/amcc/bamboo/init.S
+++ b/board/amcc/bamboo/init.S
@@ -86,14 +86,20 @@
 
 tlbtab:
     tlbtab_start
-	/*
-		0xf0000000 must be first, before relocation SA_I must be off to use the
-	    dcache as stack. It is patched after relocation to enable SA_I
-	*/
-    tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/)
-    tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
-    tlbentry( CFG_PCI_BASE, SZ_256M, 0xE0000000, 0, AC_R|AC_W|SA_G|SA_I )
-    tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, 0x80000000, 0, AC_R|AC_W|AC_X|SA_W|SA_I )
+
+    /*
+     * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+     * speed up boot process. It is patched after relocation to enable SA_I
+     */
+    tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/)
+
+    /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+    tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )
+
+    tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+    tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I )
+    tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, CFG_NVRAM_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I )
+    tlbentry( CFG_NAND_ADDR, SZ_256M, CFG_NAND_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I )
 
     /* PCI */
     tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I )
@@ -102,6 +108,6 @@
     tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I )
 
     /* USB 2.0 Device */
-    tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I )
+    tlbentry( CFG_USB_DEVICE, SZ_1K, CFG_USB_DEVICE, 0, AC_R|AC_W|SA_G|SA_I )
 
     tlbtab_end
diff --git a/cpu/ppc4xx/440gx_enet.c b/cpu/ppc4xx/440gx_enet.c
index 63227fa..68cbf34 100644
--- a/cpu/ppc4xx/440gx_enet.c
+++ b/cpu/ppc4xx/440gx_enet.c
@@ -375,8 +375,8 @@
 		out32 (RGMII_FER, ((RGMII_FER_RGMII << RGMII_FER_V (2)) |
 				   (RGMII_FER_RGMII << RGMII_FER_V (3))));
 	}
-
 #endif
+
 	out32 (ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum));
 	__asm__ volatile ("eieio");
 
@@ -521,13 +521,13 @@
 	}
 	mtsdr(sdr_mfr, reg);
 #endif
+
 	/* Set ZMII/RGMII speed according to the phy link speed */
 	reg = in32 (ZMII_SSR);
 	if ( (speed == 100) || (speed == 1000) )
 		out32 (ZMII_SSR, reg | (ZMII_SSR_SP << ZMII_SSR_V (devnum)));
 	else
-		out32 (ZMII_SSR,
-		       reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum))));
+		out32 (ZMII_SSR, reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum))));
 
 	if ((devnum == 2) || (devnum == 3)) {
 		if (speed == 1000)
@@ -672,7 +672,7 @@
 		/* set RX buffer size */
 		mtdcr (malrcbs3, ENET_MAX_MTU_ALIGNED / 16);
 		break;
-#endif /*CONFIG_440GX */
+#endif /* CONFIG_440GX */
 	case 0:
 	default:
 		/* setup MAL tx & rx channel pointers */
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 88bbadf..64ea6be 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -32,11 +32,18 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_BAMBOO		1	/* Board is BAMBOO              */
 #define CONFIG_440EP		1	/* Specific PPC440EP support    */
-
 #define CONFIG_4xx		1	/* ... PPC4xx family	        */
-#define CONFIG_BOARD_EARLY_INIT_F 	1   /* Call board_early_init_f	*/
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 
+#define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
+
+/*
+ * Please note that, if NAND support is enabled, the 2nd ethernet port
+ * can't be used because of pin multiplexing. So, if you want to use the
+ * 2nd ethernet port you have to "undef" the following define.
+ */
+#define CONFIG_BAMBOO_NAND      1       /* enable nand flash support    */
+
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
@@ -58,13 +65,15 @@
 
 #define CFG_USB_DEVICE          0x50000000
 #define CFG_NVRAM_BASE_ADDR     0x80000000
-#define CFG_BCSR_BASE	        (CFG_NVRAM_BASE_ADDR | 0x2000)
+#define CFG_BOOT_BASE_ADDR      0xf0000000
+#define CFG_NAND_ADDR           0x90000000
+#define CFG_NAND2_ADDR          0x94000000
 
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in SDRAM)
  *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR	0xf0000000		/* DCache       */
-#define CFG_INIT_RAM_END	0x1000
+#define CFG_INIT_RAM_ADDR	0x70000000		/* DCache       */
+#define CFG_INIT_RAM_END	(8 << 10)
 #define CFG_GBL_DATA_SIZE	256		    	/* num bytes initial data	*/
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -88,7 +97,7 @@
  * The DS1558 code assumes this condition
  *
  *----------------------------------------------------------------------*/
-#define CFG_NVRAM_SIZE	    (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
+#define CFG_NVRAM_SIZE	        (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs     */
 #define CONFIG_RTC_DS1556	1		         /* DS1556 RTC		*/
 
 /*-----------------------------------------------------------------------
@@ -118,22 +127,81 @@
 #define CFG_FLASH_ADDR1         0x2aa
 #define CFG_FLASH_WORD_SIZE     unsigned char
 
-#define CFG_FLASH_2ND_16BIT_DEV 1         /* bamboo has 8 and 16bit device     */
-#define CFG_FLASH_2ND_ADDR      0x87800000  /* bamboo has 8 and 16bit device     */
+#define CFG_FLASH_2ND_16BIT_DEV 1         /* bamboo has 8 and 16bit device      */
+#define CFG_FLASH_2ND_ADDR      0x87800000  /* bamboo has 8 and 16bit device    */
 
 #ifdef CFG_ENV_IS_IN_FLASH
 #define CFG_ENV_SECT_SIZE	0x10000 	/* size of one complete sector	*/
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
 
-#if 0 /* test-only */
 /* Address and size of Redundant Environment Sector	*/
 #define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
-#endif
 #endif /* CFG_ENV_IS_IN_FLASH */
 
 /*-----------------------------------------------------------------------
+ * NAND-FLASH related
+ *----------------------------------------------------------------------*/
+#define NAND_CMD_REG   (0x00) /* NandFlash Command Register */
+#define NAND_ADDR_REG  (0x04) /* NandFlash Address Register */
+#define NAND_DATA_REG  (0x08) /* NandFlash Data Register */
+#define NAND_ECC0_REG  (0x10) /* NandFlash ECC Register0 */
+#define NAND_ECC1_REG  (0x14) /* NandFlash ECC Register1 */
+#define NAND_ECC2_REG  (0x18) /* NandFlash ECC Register2 */
+#define NAND_ECC3_REG  (0x1C) /* NandFlash ECC Register3 */
+#define NAND_ECC4_REG  (0x20) /* NandFlash ECC Register4 */
+#define NAND_ECC5_REG  (0x24) /* NandFlash ECC Register5 */
+#define NAND_ECC6_REG  (0x28) /* NandFlash ECC Register6 */
+#define NAND_ECC7_REG  (0x2C) /* NandFlash ECC Register7 */
+#define NAND_CR0_REG   (0x30) /* NandFlash Device Bank0 Config Register */
+#define NAND_CR1_REG   (0x34) /* NandFlash Device Bank1 Config Register */
+#define NAND_CR2_REG   (0x38) /* NandFlash Device Bank2 Config Register */
+#define NAND_CR3_REG   (0x3C) /* NandFlash Device Bank3 Config Register */
+#define NAND_CCR_REG   (0x40) /* NandFlash Core Configuration Register */
+#define NAND_STAT_REG  (0x44) /* NandFlash Device Status Register */
+#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */
+#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */
+
+/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */
+#define NAND0_CMD_READ1_HALF1     0x00     /* Starting addr for 1rst half of registers */
+#define NAND0_CMD_READ1_HALF2     0x01     /* Starting addr for 2nd half of registers */
+#define NAND0_CMD_READ2           0x50
+#define NAND0_CMD_READ_ID         0x90
+#define NAND0_CMD_READ_STATUS     0x70
+#define NAND0_CMD_RESET           0xFF
+#define NAND0_CMD_PAGE_PROG       0x80
+#define NAND0_CMD_PAGE_PROG_TRUE  0x10
+#define NAND0_CMD_PAGE_PROG_DUMMY 0x11
+#define NAND0_CMD_BLOCK_ERASE     0x60
+#define NAND0_CMD_BLOCK_ERASE_END 0xD0
+
+#define CFG_MAX_NAND_DEVICE     1	/* Max number of NAND devices */
+#define SECTORSIZE              512
+
+#define ADDR_COLUMN             1
+#define ADDR_PAGE               2
+#define ADDR_COLUMN_PAGE        3
+
+#define NAND_ChipID_UNKNOWN     0x00
+#define NAND_MAX_FLOORS         1
+#define NAND_MAX_CHIPS          1
+
+#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0)
+#define WRITE_NAND(d, adr)      do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0)
+#define READ_NAND(adr)          (*(volatile u8 *)((ulong)adr+NAND_DATA_REG))
+#define NAND_WAIT_READY(nand)   while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01))
+
+/* not needed with 440EP NAND controller */
+#define NAND_CTL_CLRALE(nandptr)
+#define NAND_CTL_SETALE(nandptr)
+#define NAND_CTL_CLRCLE(nandptr)
+#define NAND_CTL_SETCLE(nandptr)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
+
+/*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------------- */
 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for setup             */
@@ -206,10 +274,14 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI        1       /* required for netconsole      */
 #define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
+
+#ifndef CONFIG_BAMBOO_NAND
+#define CONFIG_NET_MULTI        1       /* required for netconsole      */
 #define CONFIG_PHY1_ADDR        1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
+#endif /* CONFIG_BAMBOO_NAND */
+
 #define CONFIG_NO_PHY_RESET     1       /* no PHY reset on bamboo!!!    */
 
 #define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
@@ -228,8 +300,15 @@
 #define USB_2_0_DEVICE
 #endif /*CONFIG_440EP*/
 
+#ifdef CONFIG_BAMBOO_NAND
+#define _CFG_CMD_NAND CFG_CMD_NAND
+#else
+#define _CFG_CMD_NAND 0
+#endif /* CONFIG_BAMBOO_NAND */
+
 #define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
 				CFG_CMD_ASKENV	| \
+				CFG_CMD_EEPROM	| \
 				CFG_CMD_DATE	| \
 				CFG_CMD_DHCP	| \
 				CFG_CMD_DIAG	| \
@@ -244,6 +323,7 @@
 				CFG_CMD_REGINFO	| \
 				CFG_CMD_SDRAM	| \
 				CFG_CMD_USB	| \
+				_CFG_CMD_NAND	| \
 				CFG_CMD_SNTP	)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -253,42 +333,42 @@
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
 
 #define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		    1	/* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI          1   /* support kdi files */
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+#define CONFIG_LYNXKDI          1       /* support kdi files            */
 
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
 /* General PCI */
-#define CONFIG_PCI			            /* include pci support	        */
-#undef  CONFIG_PCI_PNP			        /* do (not) pci plug-and-play         */
+#define CONFIG_PCI			/* include pci support	        */
+#undef  CONFIG_PCI_PNP			/* do (not) pci plug-and-play   */
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
-#define CFG_PCI_TARGBASE    0x80000000  /* PCIaddr mapped to CFG_PCI_MEMBASE */
+#define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
 
 /* Board-specific PCI */
 #define CFG_PCI_PRE_INIT                /* enable board pci_pre_init()  */
 #define CFG_PCI_TARGET_INIT
 #define CFG_PCI_MASTER_INIT
 
-#define CFG_PCI_SUBSYS_VENDORID 0x1014  /* IBM */
-#define CFG_PCI_SUBSYS_ID 0xcafe        /* Whatever */
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
+#define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever */
 
 /*
  * For booting Linux, the board info and command line data
@@ -300,7 +380,7 @@
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		32768	/* For IBM 440 CPUs			*/
+#define CFG_DCACHE_SIZE		(32<<10) /* For IBM 440 CPUs			*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/