docs: cleanup typos on readthrough
Type: style
Change-Id: I3b15035ea6c13cd1ca3cdc9dfa9b10a6e1be9880
Signed-off-by: Paul Vinciguerra <pvinci@vinciconsulting.com>
diff --git a/docs/gettingstarted/users/configuring/hugepages.rst b/docs/gettingstarted/users/configuring/hugepages.rst
index 3019a20..7a1e0bd 100644
--- a/docs/gettingstarted/users/configuring/hugepages.rst
+++ b/docs/gettingstarted/users/configuring/hugepages.rst
@@ -24,7 +24,7 @@
# All groups allowed to access hugepages
vm.hugetlb_shm_group=0
- # Shared Memory Max must be greator or equal to the total size of hugepages.
+ # Shared Memory Max must be greater or equal to the total size of hugepages.
# For 2MB pages, TotalHugepageSize = vm.nr_hugepages * 2 * 1024 * 1024
# If the existing kernel.shmmax setting (cat /sys/proc/kernel/shmmax)
# is greater than the calculated TotalHugepageSize then set this parameter
diff --git a/docs/gettingstarted/users/configuring/startup.rst b/docs/gettingstarted/users/configuring/startup.rst
index df96ff7..7a66394 100644
--- a/docs/gettingstarted/users/configuring/startup.rst
+++ b/docs/gettingstarted/users/configuring/startup.rst
@@ -244,7 +244,7 @@
**Example:** cli-prompt vpp-2
* **cli-history-limit <n>**
- Limit commmand history to <n> lines. A value of 0 disables command history.
+ Limit command history to <n> lines. A value of 0 disables command history.
Default value: 50
**Example:** cli-history-limit 100
@@ -336,7 +336,7 @@
for all NICs except VICs, using ENIC driver, which has VLAN stripping on
by default.
* **hqos**
- Enable the Hierarchical Quaity-of-Service (HQoS) scheduler, default is
+ Enable the Hierarchical Quality-of-Service (HQoS) scheduler, default is
disabled. This enables HQoS on specific output interface.
* **hqos { .. }**
HQoS can also have its own set of custom parameters. Setting a custom
@@ -413,7 +413,7 @@
**Example:** enable-tcp-udp-checksum
* **no-multi-seg**
- Disable mutli-segment buffers, improves performance but disables Jumbo MTU
+ Disable multi-segment buffers, improves performance but disables Jumbo MTU
support.
**Example:** no-multi-seg
@@ -435,7 +435,7 @@
**Example:** log-level error
* **dev default { .. }**
- Change default settings for all intefaces. This sections supports the
+ Change default settings for all interfaces. This sections supports the
same set of custom parameters described in *'dev <pci-dev> { .. }*'.
**Example:**
@@ -1216,8 +1216,8 @@
A plugin can be disabled by default. It may still be in an experimental phase
or only be needed in special circumstances. If this is the case, the plugin can
-be explicitely enabled in *'startup.conf'*. Also, a plugin that is enabled by
-default can be explicitely disabled in *'startup.conf'*.
+be explicitly enabled in *'startup.conf'*. Also, a plugin that is enabled by
+default can be explicitly disabled in *'startup.conf'*.
Another useful use of this section is to disable all the plugins, then enable
only the plugins that are desired.