Typos. A bunch of typos I've been collecting.
Change-Id: I53ab8d17914e6563110354e4052109ac02bf8f3b
Signed-off-by: Paul Vinciguerra <pvinci@vinciconsulting.com>
diff --git a/test/test_mpls.py b/test/test_mpls.py
index 09e4752..8d5d5ab 100644
--- a/test/test_mpls.py
+++ b/test/test_mpls.py
@@ -452,7 +452,7 @@
self.verify_capture_ip4(self.pg0, rx, tx)
#
- # disposed packets have an invalid IPv4 checkusm
+ # disposed packets have an invalid IPv4 checksum
#
tx = self.create_stream_labelled_ip4(self.pg0, [VppMplsLabel(33)],
dst_ip=self.pg0.remote_ip4,
@@ -1281,7 +1281,7 @@
self.send_and_assert_no_replies(self.pg0, tx, "RPF-ID drop none")
#
- # set the RPF-ID of the enrtry to match the input packet's
+ # set the RPF-ID of the entry to match the input packet's
#
route_232_1_1_1.update_rpf_id(55)
@@ -1291,7 +1291,7 @@
self.verify_capture_ip4(self.pg1, rx, tx)
#
- # disposed packets have an invalid IPv4 checkusm
+ # disposed packets have an invalid IPv4 checksum
#
tx = self.create_stream_labelled_ip4(self.pg0, [VppMplsLabel(34)],
dst_ip="232.1.1.1", n=65,
@@ -1351,7 +1351,7 @@
self.send_and_assert_no_replies(self.pg0, tx, "RPF Miss")
#
- # set the RPF-ID of the enrtry to match the input packet's
+ # set the RPF-ID of the entry to match the input packet's
#
route_ff.update_rpf_id(55)
@@ -1371,7 +1371,7 @@
self.verify_capture_ip6_icmp(self.pg0, rx, tx)
#
- # set the RPF-ID of the enrtry to not match the input packet's
+ # set the RPF-ID of the entry to not match the input packet's
#
route_ff.update_rpf_id(56)
tx = self.create_stream_labelled_ip6(self.pg0,
@@ -1392,7 +1392,7 @@
self.tbl = VppMplsTable(self, 0)
self.tbl.add_vpp_config()
- # PG0 is MPLS enalbed
+ # PG0 is MPLS enabled
self.pg0.admin_up()
self.pg0.config_ip4()
self.pg0.resolve_arp()
@@ -1573,7 +1573,7 @@
rx0 = self.pg0._get_capture(1)
rx1 = self.pg1._get_capture(1)
- # not testig the LB hashing algorithm so we're not concerned
+ # not testing the LB hashing algorithm so we're not concerned
# with the split ratio, just as long as neither is 0
self.assertNotEqual(0, len(rx0))
self.assertNotEqual(0, len(rx1))
@@ -1581,7 +1581,7 @@
#
# use a test CLI command to stop the FIB walk process, this
# will prevent the FIB converging the VPN routes and thus allow
- # us to probe the interim (psot-fail, pre-converge) state
+ # us to probe the interim (post-fail, pre-converge) state
#
self.vapi.ppcli("test fib-walk-process disable")
@@ -1681,7 +1681,7 @@
#
# use a test CLI command to stop the FIB walk process, this
# will prevent the FIB converging the VPN routes and thus allow
- # us to probe the interim (psot-fail, pre-converge) state
+ # us to probe the interim (post-fail, pre-converge) state
#
self.vapi.ppcli("test fib-walk-process disable")
@@ -1781,7 +1781,7 @@
#
# use a test CLI command to stop the FIB walk process, this
# will prevent the FIB converging the VPN routes and thus allow
- # us to probe the interim (psot-fail, pre-converge) state
+ # us to probe the interim (post-fail, pre-converge) state
#
self.vapi.ppcli("test fib-walk-process disable")
@@ -1937,7 +1937,7 @@
self.assertEqual(rx0[0][Ether].src, payload[Ether].src)
#
- # Inject a packet from the custoer/L2 side
+ # Inject a packet from the customer/L2 side
#
tx1 = pcore[MPLS].payload * 65
rx1 = self.send_and_expect(self.pg1, tx1, self.pg0)