| ############################################################################### |
| ## |
| ## Collector Server config |
| ## |
| ## - Default values are shown as commented settings. |
| ## |
| ############################################################################### |
| ## |
| ## HTTP(S) service |
| ## |
| ## Normally: |
| ## |
| ## - 8080 is http service |
| ## - https is disabled by default (-1) |
| ## |
| ## - At this time, the server always binds to 0.0.0.0 |
| ## |
| ## The default port when header.authflag is disabled (0) |
| #collector.service.port=8080 |
| |
| ## The secure port is required if header.authflag is set to 1 (true) |
| ## Authentication is only supported via secure port |
| ## When enabled - require valid keystore defined |
| collector.service.secure.port=8443 |
| |
| ## The keystore must be setup per installation when secure port is configured |
| collector.keystore.file.location=../etc/keystore |
| collector.keystore.passwordfile=./etc/passwordfile |
| collector.keystore.alias=tomcat |
| |
| |
| ############################################################################### |
| ## Processing |
| ## |
| ## If there's a problem that prevents the collector from processing alarms, |
| ## it's normally better to apply back pressure to the caller than to try to |
| ## buffer beyond a reasonable size limit. With a limit, the server won't crash |
| ## due to being out of memory, and the caller will get a 5xx reply saying the |
| ## server is in trouble. |
| collector.inputQueue.maxPending=8096 |
| |
| ## Schema Validation checkflag |
| ## default no validation checkflag (-1) |
| ## If enabled (1) - schemafile location must be specified |
| collector.schema.checkflag=1 |
| collector.schema.file={\"v1\":\"./etc/CommonEventFormat_27.2.json\",\"v2\":\"./etc/CommonEventFormat_27.2.json\",\"v3\":\"./etc/CommonEventFormat_27.2.json\",\"v4\":\"./etc/CommonEventFormat_27.2.json\",\"v5\":\"./etc/CommonEventFormat_28.3.json\"} |
| |
| ## List all streamid per domain to be supported. The streamid should match to channel name on dmaapfile |
| collector.dmaap.streamid=fault=sec_fault|syslog=sec_syslog|heartbeat=sec_heartbeat|measurementsForVfScaling=sec_measurement|mobileFlow=sec_mobileflow|other=sec_other|stateChange=sec_statechange|thresholdCrossingAlert=sec_thresholdCrossingAlert|voiceQuality=ves_voicequality|sipSignaling=ves_sipsignaling |
| collector.dmaapfile=./etc/DmaapConfig.json |
| |
| ## Custom ExceptionConfiguration |
| exceptionConfig=./etc/ExceptionConfig.json |
| |
| ## authflag control authentication by the collector |
| ## If enabled (1) - then authlist has to be defined |
| ## When authflag is enabled, only secure port will be supported |
| ## To disable enter 0 |
| header.authflag=1 |
| ## Combination of userid,base64 encoded pwd list to be supported |
| ## userid and pwd comma separated; pipe delimitation between each pair |
| header.authlist=sample1,c2FtcGxlMQ==|vdnsagg,dmRuc2FnZw== |
| |
| ## Event transformation Flag - when set expects configurable transformation |
| ## defined under ./etc/eventTransform.json |
| ## Enabled by default; to disable set to 0 |
| event.transform.flag=0 |
| |
| ############################################################################### |
| ## |
| ## Tomcat control |
| ## |
| #tomcat.maxthreads=(tomcat default, which is usually 200) |
| |