Modify property files in active-standby-management
Remove ${env:} and update property syntax
Add new property failure.threshold
Add new property interval_sec
Update: change property syntax back to using ${env:}
Update: add 2019 to copyright information
Issue-ID: POLICY-2031
Change-Id: I6db10700189197a1306c3b8fa23dff26518be0f3
Signed-off-by: Peyton Puckett <peyton.puckett@att.com>
diff --git a/feature-active-standby-management/src/test/resources/feature-state-management.properties b/feature-active-standby-management/src/test/resources/feature-state-management.properties
index ec84090..d684391 100644
--- a/feature-active-standby-management/src/test/resources/feature-state-management.properties
+++ b/feature-active-standby-management/src/test/resources/feature-state-management.properties
@@ -2,14 +2,14 @@
# ============LICENSE_START=======================================================
# feature-active-standby-management
# ================================================================================
-# Copyright (C) 2017 AT&T Intellectual Property. All rights reserved.
+# Copyright (C) 2017, 2019 AT&T Intellectual Property. All rights reserved.
# ================================================================================
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
-#
+#
# http://www.apache.org/licenses/LICENSE-2.0
-#
+#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
@@ -37,19 +37,19 @@
# Must be unique across the system
resource.name=pdp1
-# Name of the site in which this node is hosted
+# Name of the site in which this node is hosted
site_name = pdp_1
# Forward Progress Monitor update interval seconds
fp_monitor_interval = 2
-# Failed counter threshold before failover
+# Failed counter threshold before failover
failed_counter_threshold = 1
# Interval between test transactions when no traffic seconds
test_trans_interval = 1
-# Interval between writes of the FPC to the DB seconds
+# Interval between writes of the FPC to the DB seconds
write_fpc_interval = 1
-# Node type Note: Make sure you don't leave any trailing spaces, or you'll get an 'invalid node type' error!
+# Node type Note: Make sure you don't leave any trailing spaces, or you'll get an 'invalid node type' error!
node_type = pdp_drools
-# Dependency groups are groups of resources upon which a node operational state is dependent upon.
+# Dependency groups are groups of resources upon which a node operational state is dependent upon.
# Each group is a comma-separated list of resource names and groups are separated by a semicolon. For example:
# dependency_groups=site_1.astra_1,site_1.astra_2;site_1.brms_1,site_1.brms_2;site_1.logparser_1;site_1.pypdp_1
dependency_groups=
@@ -58,14 +58,14 @@
test_via_jmx=true
# This is the max number of seconds beyond which a non incrementing FPC is considered a failure
max_fpc_update_interval=5
-# Run the state audit every 60 seconds (60000 ms). The state audit finds stale DB entries in the
-# forwardprogressentity table and marks the node as disabled/failed in the statemanagemententity
+# Run the state audit every 60 seconds (60000 ms). The state audit finds stale DB entries in the
+# forwardprogressentity table and marks the node as disabled/failed in the statemanagemententity
# table. NOTE! It will only run on nodes that have a standbystatus = providingservice.
# A value of <= 0 will turn off the state audit.
state_audit_interval_ms=-1
-# The refresh state audit is run every (default) 10 minutes (600000 ms) to clean up any state corruption in the
+# The refresh state audit is run every (default) 10 minutes (600000 ms) to clean up any state corruption in the
# DB statemanagemententity table. It only refreshes the DB state entry for the local node. That is, it does not
-# refresh the state of any other nodes. A value <= 0 will turn the audit off. Any other value will override
+# refresh the state of any other nodes. A value <= 0 will turn the audit off. Any other value will override
# the default of 600000 ms.
refresh_state_audit_interval_ms=-1
@@ -74,6 +74,8 @@
# Flag to control the execution of the subsystemTest for the Nexus Maven repository
repository.audit.is.active=false
repository.audit.ignore.errors=true
+repository.audit.interval_sec=86400
+repository.audit.failure.threshold=3
# DB Audit Properties
# Flag to control the execution of the subsystemTest for the Database