Notes on configuring dnsmasq as packaged for Debian.

(1) To configure dnsmasq edit /etc/dnsmasq.conf. The file is well
    commented; see also the dnsmasq.8 man page for explanation of
    the options. The file /etc/default/dnsmasq also exists but it
    shouldn't need to be touched in most cases. To set up DHCP
    options you might need to refer to a copy of RFC 2132. This is 
    available on Debian systems in the package doc-rfc-std as the file
    /usr/share/doc/RFC/draft-standard/rfc2132.txt.gz .

(2) Installing the dnsmasq package also creates the directory
    /etc/dnsmasq.d which is searched by dnsmasq for configuration file
    fragments. This behaviour can be disabled by editing 
    /etc/default/dnsmasq.

(3) If the Debian resolvconf package is installed then, regardless
    of what interface configuration daemons are employed, the list of
    nameservers to which dnsmasq should forward queries can be found
    in /var/run/dnsmasq/resolv.conf; also, 127.0.0.1 is listed as the
    first nameserver address in /etc/resolv.conf. This works using the
    default configurations of resolvconf and dnsmasq.

(4) In the absence of resolvconf, if you are using dhcpcd then
    dnsmasq should read the list of nameservers from the automatically
    generated file /etc/dhcpc/resolv.conf.  You should list 127.0.0.1
    as the first nameserver address in /etc/resolv.conf.

(5) In the absence of resolvconf, if you are using pppd then
    dnsmasq should read the list of nameservers from the automatically
    generated file /etc/ppp/resolv.conf.  You should list 127.0.0.1
    as the first nameserver address in /etc/resolv.conf.

(6) In the absence of resolvconf, dns-nameservers lines in 
    /etc/network/interfaces are ignored. If you do not use
    resolvconf, list 127.0.0.1 as the first nameserver address
    in /etc/resolv.conf and configure your nameservers using
    "server=<IP-address>" lines in /etc/dnsmasq.conf.

(7) If you run multiple DNS servers on a single machine, each
    listening on a different interface, then it is necessary to use 
    the bind-interfaces option by uncommenting "bind-interfaces" in 
    /etc/dnsmasq.conf. This option stops dnsmasq from binding the 
    wildcard address and allows servers listening on port 53 on
    interfaces not in use by dnsmasq to work. The Debian 
    libvirt package will add a configuration file in /etc/dnsmasq.d
    which does this so that the "system" dnsmasq and "private" dnsmasq
    instances started by libvirt do not clash.

(8) The following options are supported in DEB_BUILD_OPTIONS
      noopt       : compile without optimisation.
      nostrip     : don't remove symbols from binary. 
      nodocs      : omit documentation.
      notftp      : omit TFTP support.
      nodhcp      : omit DHCP support.
      nodhcp6     : omit DHCPv6 support.
      noscript    : omit lease-change script support.
      use_lua     : provide support for lease-change scripts written
                    in Lua.
      noipv6      : omit IPv6 support.
      nodbus      : omit DBus support.
      noconntrack : omit connection tracking support. 
      noipset     : omit IPset support.
      nortc       : compile alternate mode suitable for systems without an RTC.
      noi18n      : omit translations and internationalisation support.
      noidn       : omit international domain name support, must be
                    combined with noi18n to be effective.
      gitversion  : set the version of the produced packages from the
                    git-derived versioning information on the source,
                    rather than the debian changelog. 

(9) Dnsmasq comes as three packages - dnsmasq-utils, dnsmasq-base and
    dnsmasq. Dnsmasq-base provides the dnsmasq executable and
    documentation (including this file). Dnsmasq, which depends on
    dnsmasq-base, provides the init script and configuration
    infrastructure. This file assumes that both are installed. It is
    possible to install only dnsmasq-base and use dnsmasq as a
    non-"system" daemon. Libvirt, for instance, does this.
    Dnsmasq-utils provides the utilities dhcp_release and 
    dhcp_lease_time.