| .. _iperf3: |
| |
| Introduction |
| ============ |
| |
| This tutorial shows how to use VPP use iperf3 and Trex to get some basic peformance |
| numbers from a few basic configurations. Four examples are shown. In the first two |
| examples, the **iperf3** tool is used to generate traffic, and in the last two examples |
| the Cisco's `TRex Realistic Traffic Generator <http://trex-tgn.cisco.com/>`_ is used. For |
| comparison purposes, the first example shows packet forwarding using ordinary kernel |
| IP forwarding, and the second example shows packet forwarding using VPP. |
| |
| Three Intel Xeon processor platform systems are used to connect to the VPP host to pass traffic |
| using **iperf3** and Cisco’s `TRex <http://trex-tgn.cisco.com/>`_. |
| |
| Intel 40 Gigabit Ethernet (GbE) network interface cards (NICs) are used to connect the hosts. |
| |
| |
| Using Kernel Packet Forwarding with Iperf3 |
| =========================================== |
| |
| In this test, 40 GbE Intel Ethernet Network Adapters are used to connect the three |
| systems. Figure 1 illustrates this configuration. |
| |
| .. figure:: /_images/iperf3fig1.png |
| |
| Figure 1: VPP runs on a host that connects to two other systems via 40 GbE NICs. |
| |
| For comparison purposes, in the first example, we configure kernel forwarding in |
| *csp2s22c03* and use the **iperf3** tool to measure network bandwidth between |
| *csp2s22c03* and *net2s22c05*. |
| |
| In the second example, we start the VPP engine in *csp2s22c03* instead of using |
| kernel forwarding. On *csp2s22c03*, we configure the system to have the addresses |
| 10.10.1.1/24 and 10.10.2.1/24 on the two 40-GbE NICs. To find all network interfaces |
| available on the system, use the lshw Linux command to list all network interfaces |
| and the corresponding slots *[0000:xx:yy.z]*. |
| |
| In this example, the 40-GbE interfaces are *ens802f0* and *ens802f1*. |
| |
| .. code-block:: console |
| |
| csp2s22c03$ sudo lshw -class network -businfo |
| Bus info Device Class Description |
| ======================================================== |
| pci@0000:03:00.0 enp3s0f0 network Ethernet Controller 10-Gig |
| pci@0000:03:00.1 enp3s0f1 network Ethernet Controller 10-Gig |
| pci@0000:82:00.0 ens802f0 network Ethernet Controller XL710 |
| pci@0000:82:00.1 ens802f1 network Ethernet Controller XL710 |
| pci@0000:82:00.0 ens802f0d1 network Ethernet interface |
| pci@0000:82:00.1 ens802f1d1 network Ethernet interface |
| |
| |
| Configure the system *csp2s22c03* to have 10.10.1.1 and 10.10.2.1 on the two 40-GbE NICs |
| *ens802f0* and *ens802f1*, respectively. |
| |
| .. code-block:: console |
| |
| csp2s22c03$ sudo ip addr add 10.10.1.1/24 dev ens802f0 |
| csp2s22c03$ sudo ip link set dev ens802f0 up |
| csp2s22c03$ sudo ip addr add 10.10.2.1/24 dev ens802f1 |
| csp2s22c03$ sudo ip link set dev ens802f1 up |
| |
| List the route table: |
| |
| .. code-block:: console |
| |
| csp2s22c03$ route |
| Kernel IP routing table |
| Destination Gateway Genmask Flags Metric Ref Use Iface |
| default jf111-ldr1a-530 0.0.0.0 UG 0 0 0 enp3s0f1 |
| default 192.168.0.50 0.0.0.0 UG 100 0 0 enp3s0f0 |
| 10.10.1.0 * 255.255.255.0 U 0 0 0 ens802f0 |
| 10.10.2.0 * 255.255.255.0 U 0 0 0 ens802f1 |
| 10.23.3.0 * 255.255.255.0 U 0 0 0 enp3s0f1 |
| link-local * 255.255.0.0 U 1000 0 0 enp3s0f1 |
| 192.168.0.0 * 255.255.255.0 U 100 0 0 enp3s0f0 |
| |
| .. code-block:: console |
| |
| csp2s22c03$ ip route |
| default via 10.23.3.1 dev enp3s0f1 |
| default via 192.168.0.50 dev enp3s0f0 proto static metric 100 |
| 10.10.1.0/24 dev ens802f0 proto kernel scope link src 10.10.1.1 |
| 10.10.2.0/24 dev ens802f1 proto kernel scope link src 10.10.2.1 |
| 10.23.3.0/24 dev enp3s0f1 proto kernel scope link src 10.23.3.67 |
| 169.254.0.0/16 dev enp3s0f1 scope link metric 1000 |
| 192.168.0.0/24 dev enp3s0f0 proto kernel scope link src 192.168.0.142 metric 100 |
| |
| On *csp2s22c04*, we configure the system to have the address 10.10.1.2 and use |
| the interface *ens802* to route IP packets 10.10.2.0/24. Use the lshw Linux |
| command to list all network interfaces and the corresponding slots *[0000:xx:yy.z]*. |
| |
| For example, the interface *ens802d1* *(ens802)* is connected to slot *[82:00.0]*: |
| |
| .. code-block:: console |
| |
| csp2s22c04$ sudo lshw -class network -businfo |
| Bus info Device Class Description |
| ===================================================== |
| pci@0000:03:00.0 enp3s0f0 network Ethernet Controller 10-Gigabit X540-AT2 |
| pci@0000:03:00.1 enp3s0f1 network Ethernet Controller 10-Gigabit X540-AT2 |
| pci@0000:82:00.0 ens802d1 network Ethernet Controller XL710 for 40GbE QSFP+ |
| pci@0000:82:00.0 ens802 network Ethernet interface |
| |
| For kernel forwarding, set 10.10.1.2 to the interface *ens802*, and add a static |
| route for IP packet 10.10.2.0/24: |
| |
| .. code-block:: console |
| |
| csp2s22c04$ sudo ip addr add 10.10.1.2/24 dev ens802 |
| csp2s22c04$ sudo ip link set dev ens802 up |
| csp2s22c04$ sudo ip route add 10.10.2.0/24 via 10.10.1.1 |
| |
| .. code-block:: console |
| |
| csp2s22c04$ ifconfig |
| enp3s0f0 Link encap:Ethernet HWaddr a4:bf:01:00:92:73 |
| inet addr:10.23.3.62 Bcast:10.23.3.255 Mask:255.255.255.0 |
| inet6 addr: fe80::a6bf:1ff:fe00:9273/64 Scope:Link |
| UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 |
| RX packets:3411 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:1179 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:1000 |
| RX bytes:262230 (262.2 KB) TX bytes:139975 (139.9 KB) |
| |
| ens802 Link encap:Ethernet HWaddr 68:05:ca:2e:76:e0 |
| inet addr:10.10.1.2 Bcast:0.0.0.0 Mask:255.255.255.0 |
| inet6 addr: fe80::6a05:caff:fe2e:76e0/64 Scope:Link |
| UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 |
| RX packets:0 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:40 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:1000 |
| RX bytes:0 (0.0 B) TX bytes:5480 (5.4 KB) |
| |
| lo Link encap:Local Loopback |
| inet addr:127.0.0.1 Mask:255.0.0.0 |
| inet6 addr: ::1/128 Scope:Host |
| UP LOOPBACK RUNNING MTU:65536 Metric:1 |
| RX packets:31320 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:31320 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:1 |
| RX bytes:40301788 (40.3 MB) TX bytes:40301788 (40.3 MB) |
| |
| After setting the route, we can ping from *csp2s22c03* to *csp2s22c04*, and vice versa: |
| |
| .. code-block:: console |
| |
| csp2s22c03$ ping 10.10.1.2 -c 3 |
| PING 10.10.1.2 (10.10.1.2) 56(84) bytes of data. |
| 64 bytes from 10.10.1.2: icmp_seq=1 ttl=64 time=0.122 ms |
| 64 bytes from 10.10.1.2: icmp_seq=2 ttl=64 time=0.109 ms |
| 64 bytes from 10.10.1.2: icmp_seq=3 ttl=64 time=0.120 ms |
| |
| .. code-block:: console |
| |
| csp2s22c04$ ping 10.10.1.1 -c 3 |
| PING 10.10.1.1 (10.10.1.1) 56(84) bytes of data. |
| 64 bytes from 10.10.1.1: icmp_seq=1 ttl=64 time=0.158 ms |
| 64 bytes from 10.10.1.1: icmp_seq=2 ttl=64 time=0.096 ms |
| 64 bytes from 10.10.1.1: icmp_seq=3 ttl=64 time=0.102 ms |
| |
| Similarly, on *net2s22c05*, we configure the system to have the address *10.10.2.2* |
| and use the interface *ens803f0* to route IP packets *10.10.1.0/24*. Use the lshw |
| Linux command to list all network interfaces and the corresponding slots |
| *[0000:xx:yy.z]*. For example, the interface *ens803f0* is connected to slot *[87:00.0]*: |
| |
| .. code-block:: console |
| |
| NET2S22C05$ sudo lshw -class network -businfo |
| Bus info Device Class Description |
| ======================================================== |
| pci@0000:03:00.0 enp3s0f0 network Ethernet Controller 10-Gigabit X540-AT2 |
| pci@0000:03:00.1 enp3s0f1 network Ethernet Controller 10-Gigabit X540-AT2 |
| pci@0000:81:00.0 ens787f0 network 82599 10 Gigabit TN Network Connection |
| pci@0000:81:00.1 ens787f1 network 82599 10 Gigabit TN Network Connection |
| pci@0000:87:00.0 ens803f0 network Ethernet Controller XL710 for 40GbE QSFP+ |
| pci@0000:87:00.1 ens803f1 network Ethernet Controller XL710 for 40GbE QSFP+ |
| |
| For kernel forwarding, set 10.10.2.2 to the interface ens803f0, and add a static |
| route for IP packet 10.10.1.0/24: |
| |
| .. code-block:: console |
| |
| NET2S22C05$ sudo ip addr add 10.10.2.2/24 dev ens803f0 |
| NET2S22C05$ sudo ip link set dev ens803f0 up |
| NET2S22C05$ sudo ip route add 10.10.1.0/24 via 10.10.2.1 |
| |
| After setting the route, you can ping from *csp2s22c03* to *net2s22c05*, and vice |
| versa. However, in order to ping between *net2s22c05* and *csp2s22c04*, kernel IP |
| forwarding in *csp2s22c03* has to be enabled: |
| |
| .. code-block:: console |
| |
| csp2s22c03$ sysctl net.ipv4.ip_forward |
| net.ipv4.ip_forward = 0 |
| csp2s22c03$ echo 1 | sudo tee /proc/sys/net/ipv4/ip_forward |
| csp2s22c03$ sysctl net.ipv4.ip_forward |
| net.ipv4.ip_forward = 1 |
| |
| If successful, verify that now you can ping between *net2s22c05* and *csp2s22c04*: |
| |
| .. code-block:: console |
| |
| NET2S22C05$ ping 10.10.1.2 -c 3 |
| PING 10.10.1.2 (10.10.1.2) 56(84) bytes of data. |
| 64 bytes from 10.10.1.2: icmp_seq=1 ttl=63 time=0.239 ms |
| 64 bytes from 10.10.1.2: icmp_seq=2 ttl=63 time=0.224 ms |
| 64 bytes from 10.10.1.2: icmp_seq=3 ttl=63 time=0.230 ms |
| |
| We use the **iperf3** utility to measure network bandwidth between hosts. In this |
| test, we download the **iperf3** utility tool on both *net2s22c05* and *csp2s22c04*. |
| On *csp2s22c04*, we start the **iperf3** server with “iperf3 –s”, and then on *net2s22c05*, |
| we start the **iperf3** client to connect to the server: |
| |
| .. code-block:: console |
| |
| NET2S22C05$ iperf3 -c 10.10.1.2 |
| Connecting to host 10.10.1.2, port 5201 |
| [ 4] local 10.10.2.2 port 54074 connected to 10.10.1.2 port 5201 |
| [ ID] Interval Transfer Bandwidth Retr Cwnd |
| [ 4] 0.00-1.00 sec 936 MBytes 7.85 Gbits/sec 2120 447 KBytes |
| [ 4] 1.00-2.00 sec 952 MBytes 7.99 Gbits/sec 1491 611 KBytes |
| [ 4] 2.00-3.00 sec 949 MBytes 7.96 Gbits/sec 2309 604 KBytes |
| [ 4] 3.00-4.00 sec 965 MBytes 8.10 Gbits/sec 1786 571 KBytes |
| [ 4] 4.00-5.00 sec 945 MBytes 7.93 Gbits/sec 1984 424 KBytes |
| [ 4] 5.00-6.00 sec 946 MBytes 7.94 Gbits/sec 1764 611 KBytes |
| [ 4] 6.00-7.00 sec 979 MBytes 8.21 Gbits/sec 1499 655 KBytes |
| [ 4] 7.00-8.00 sec 980 MBytes 8.22 Gbits/sec 1182 867 KBytes |
| [ 4] 8.00-9.00 sec 1008 MBytes 8.45 Gbits/sec 945 625 KBytes |
| [ 4] 9.00-10.00 sec 1015 MBytes 8.51 Gbits/sec 1394 611 KBytes |
| - - - - - - - - - - - - - - - - - - - - - - - - - |
| [ ID] Interval Transfer Bandwidth Retr |
| [ 4] 0.00-10.00 sec 9.45 GBytes 8.12 Gbits/sec 16474 sender |
| [ 4] 0.00-10.00 sec 9.44 GBytes 8.11 Gbits/sec receiver |
| |
| iperf Done. |