| # Configuration file for dnsmasq. |
| # |
| # Format is one option per line, legal options are the same |
| # as the long options legal on the command line. See |
| # "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details. |
| |
| # Listen on this specific port instead of the standard DNS port |
| # (53). Setting this to zero completely disables DNS function, |
| # leaving only DHCP and/or TFTP. |
| #port=5353 |
| |
| # The following two options make you a better netizen, since they |
| # tell dnsmasq to filter out queries which the public DNS cannot |
| # answer, and which load the servers (especially the root servers) |
| # unnecessarily. If you have a dial-on-demand link they also stop |
| # these requests from bringing up the link unnecessarily. |
| |
| # Never forward plain names (without a dot or domain part) |
| #domain-needed |
| # Never forward addresses in the non-routed address spaces. |
| #bogus-priv |
| |
| # Uncomment these to enable DNSSEC validation and caching: |
| # (Requires dnsmasq to be built with DNSSEC option.) |
| #conf-file=%%PREFIX%%/share/dnsmasq/trust-anchors.conf |
| #dnssec |
| |
| # Replies which are not DNSSEC signed may be legitimate, because the domain |
| # is unsigned, or may be forgeries. Setting this option tells dnsmasq to |
| # check that an unsigned reply is OK, by finding a secure proof that a DS |
| # record somewhere between the root and the domain does not exist. |
| # The cost of setting this is that even queries in unsigned domains will need |
| # one or more extra DNS queries to verify. |
| #dnssec-check-unsigned |
| |
| # Uncomment this to filter useless windows-originated DNS requests |
| # which can trigger dial-on-demand links needlessly. |
| # Note that (amongst other things) this blocks all SRV requests, |
| # so don't use it if you use eg Kerberos, SIP, XMMP or Google-talk. |
| # This option only affects forwarding, SRV records originating for |
| # dnsmasq (via srv-host= lines) are not suppressed by it. |
| #filterwin2k |
| |
| # Change this line if you want dns to get its upstream servers from |
| # somewhere other that /etc/resolv.conf |
| #resolv-file= |
| |
| # By default, dnsmasq will send queries to any of the upstream |
| # servers it knows about and tries to favour servers to are known |
| # to be up. Uncommenting this forces dnsmasq to try each query |
| # with each server strictly in the order they appear in |
| # /etc/resolv.conf |
| #strict-order |
| |
| # If you don't want dnsmasq to read /etc/resolv.conf or any other |
| # file, getting its servers from this file instead (see below), then |
| # uncomment this. |
| #no-resolv |
| |
| # If you don't want dnsmasq to poll /etc/resolv.conf or other resolv |
| # files for changes and re-read them then uncomment this. |
| #no-poll |
| |
| # Add other name servers here, with domain specs if they are for |
| # non-public domains. |
| #server=/localnet/192.168.0.1 |
| |
| # Example of routing PTR queries to nameservers: this will send all |
| # address->name queries for 192.168.3/24 to nameserver 10.1.2.3 |
| #server=/3.168.192.in-addr.arpa/10.1.2.3 |
| |
| # Add local-only domains here, queries in these domains are answered |
| # from /etc/hosts or DHCP only. |
| #local=/localnet/ |
| |
| # Add domains which you want to force to an IP address here. |
| # The example below send any host in double-click.net to a local |
| # web-server. |
| #address=/double-click.net/127.0.0.1 |
| |
| # --address (and --server) work with IPv6 addresses too. |
| #address=/www.thekelleys.org.uk/fe80::20d:60ff:fe36:f83 |
| |
| # Add the IPs of all queries to yahoo.com, google.com, and their |
| # subdomains to the vpn and search ipsets: |
| #ipset=/yahoo.com/google.com/vpn,search |
| |
| # You can control how dnsmasq talks to a server: this forces |
| # queries to 10.1.2.3 to be routed via eth1 |
| # server=10.1.2.3@eth1 |
| |
| # and this sets the source (ie local) address used to talk to |
| # 10.1.2.3 to 192.168.1.1 port 55 (there must be an interface with that |
| # IP on the machine, obviously). |
| # server=10.1.2.3@192.168.1.1#55 |
| |
| # If you want dnsmasq to change uid and gid to something other |
| # than the default, edit the following lines. |
| #user= |
| #group= |
| |
| # If you want dnsmasq to listen for DHCP and DNS requests only on |
| # specified interfaces (and the loopback) give the name of the |
| # interface (eg eth0) here. |
| # Repeat the line for more than one interface. |
| #interface= |
| # Or you can specify which interface _not_ to listen on |
| #except-interface= |
| # Or which to listen on by address (remember to include 127.0.0.1 if |
| # you use this.) |
| #listen-address= |
| # If you want dnsmasq to provide only DNS service on an interface, |
| # configure it as shown above, and then use the following line to |
| # disable DHCP and TFTP on it. |
| #no-dhcp-interface= |
| |
| # On systems which support it, dnsmasq binds the wildcard address, |
| # even when it is listening on only some interfaces. It then discards |
| # requests that it shouldn't reply to. This has the advantage of |
| # working even when interfaces come and go and change address. If you |
| # want dnsmasq to really bind only the interfaces it is listening on, |
| # uncomment this option. About the only time you may need this is when |
| # running another nameserver on the same machine. |
| #bind-interfaces |
| |
| # If you don't want dnsmasq to read /etc/hosts, uncomment the |
| # following line. |
| #no-hosts |
| # or if you want it to read another file, as well as /etc/hosts, use |
| # this. |
| #addn-hosts=/etc/banner_add_hosts |
| |
| # Set this (and domain: see below) if you want to have a domain |
| # automatically added to simple names in a hosts-file. |
| #expand-hosts |
| |
| # Set the domain for dnsmasq. this is optional, but if it is set, it |
| # does the following things. |
| # 1) Allows DHCP hosts to have fully qualified domain names, as long |
| # as the domain part matches this setting. |
| # 2) Sets the "domain" DHCP option thereby potentially setting the |
| # domain of all systems configured by DHCP |
| # 3) Provides the domain part for "expand-hosts" |
| #domain=thekelleys.org.uk |
| |
| # Set a different domain for a particular subnet |
| #domain=wireless.thekelleys.org.uk,192.168.2.0/24 |
| |
| # Same idea, but range rather then subnet |
| #domain=reserved.thekelleys.org.uk,192.68.3.100,192.168.3.200 |
| |
| # Uncomment this to enable the integrated DHCP server, you need |
| # to supply the range of addresses available for lease and optionally |
| # a lease time. If you have more than one network, you will need to |
| # repeat this for each network on which you want to supply DHCP |
| # service. |
| #dhcp-range=192.168.0.50,192.168.0.150,12h |
| |
| # This is an example of a DHCP range where the netmask is given. This |
| # is needed for networks we reach the dnsmasq DHCP server via a relay |
| # agent. If you don't know what a DHCP relay agent is, you probably |
| # don't need to worry about this. |
| #dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h |
| |
| # This is an example of a DHCP range which sets a tag, so that |
| # some DHCP options may be set only for this network. |
| #dhcp-range=set:red,192.168.0.50,192.168.0.150 |
| |
| # Use this DHCP range only when the tag "green" is set. |
| #dhcp-range=tag:green,192.168.0.50,192.168.0.150,12h |
| |
| # Specify a subnet which can't be used for dynamic address allocation, |
| # is available for hosts with matching --dhcp-host lines. Note that |
| # dhcp-host declarations will be ignored unless there is a dhcp-range |
| # of some type for the subnet in question. |
| # In this case the netmask is implied (it comes from the network |
| # configuration on the machine running dnsmasq) it is possible to give |
| # an explicit netmask instead. |
| #dhcp-range=192.168.0.0,static |
| |
| # Enable DHCPv6. Note that the prefix-length does not need to be specified |
| # and defaults to 64 if missing/ |
| #dhcp-range=1234::2, 1234::500, 64, 12h |
| |
| # Do Router Advertisements, BUT NOT DHCP for this subnet. |
| #dhcp-range=1234::, ra-only |
| |
| # Do Router Advertisements, BUT NOT DHCP for this subnet, also try and |
| # add names to the DNS for the IPv6 address of SLAAC-configured dual-stack |
| # hosts. Use the DHCPv4 lease to derive the name, network segment and |
| # MAC address and assume that the host will also have an |
| # IPv6 address calculated using the SLAAC algorithm. |
| #dhcp-range=1234::, ra-names |
| |
| # Do Router Advertisements, BUT NOT DHCP for this subnet. |
| # Set the lifetime to 46 hours. (Note: minimum lifetime is 2 hours.) |
| #dhcp-range=1234::, ra-only, 48h |
| |
| # Do DHCP and Router Advertisements for this subnet. Set the A bit in the RA |
| # so that clients can use SLAAC addresses as well as DHCP ones. |
| #dhcp-range=1234::2, 1234::500, slaac |
| |
| # Do Router Advertisements and stateless DHCP for this subnet. Clients will |
| # not get addresses from DHCP, but they will get other configuration information. |
| # They will use SLAAC for addresses. |
| #dhcp-range=1234::, ra-stateless |
| |
| # Do stateless DHCP, SLAAC, and generate DNS names for SLAAC addresses |
| # from DHCPv4 leases. |
| #dhcp-range=1234::, ra-stateless, ra-names |
| |
| # Do router advertisements for all subnets where we're doing DHCPv6 |
| # Unless overridden by ra-stateless, ra-names, et al, the router |
| # advertisements will have the M and O bits set, so that the clients |
| # get addresses and configuration from DHCPv6, and the A bit reset, so the |
| # clients don't use SLAAC addresses. |
| #enable-ra |
| |
| # Supply parameters for specified hosts using DHCP. There are lots |
| # of valid alternatives, so we will give examples of each. Note that |
| # IP addresses DO NOT have to be in the range given above, they just |
| # need to be on the same network. The order of the parameters in these |
| # do not matter, it's permissible to give name, address and MAC in any |
| # order. |
| |
| # Always allocate the host with Ethernet address 11:22:33:44:55:66 |
| # The IP address 192.168.0.60 |
| #dhcp-host=11:22:33:44:55:66,192.168.0.60 |
| |
| # Always set the name of the host with hardware address |
| # 11:22:33:44:55:66 to be "fred" |
| #dhcp-host=11:22:33:44:55:66,fred |
| |
| # Always give the host with Ethernet address 11:22:33:44:55:66 |
| # the name fred and IP address 192.168.0.60 and lease time 45 minutes |
| #dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m |
| |
| # Give a host with Ethernet address 11:22:33:44:55:66 or |
| # 12:34:56:78:90:12 the IP address 192.168.0.60. Dnsmasq will assume |
| # that these two Ethernet interfaces will never be in use at the same |
| # time, and give the IP address to the second, even if it is already |
| # in use by the first. Useful for laptops with wired and wireless |
| # addresses. |
| #dhcp-host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.60 |
| |
| # Give the machine which says its name is "bert" IP address |
| # 192.168.0.70 and an infinite lease |
| #dhcp-host=bert,192.168.0.70,infinite |
| |
| # Always give the host with client identifier 01:02:02:04 |
| # the IP address 192.168.0.60 |
| #dhcp-host=id:01:02:02:04,192.168.0.60 |
| |
| # Always give the InfiniBand interface with hardware address |
| # 80:00:00:48:fe:80:00:00:00:00:00:00:f4:52:14:03:00:28:05:81 the |
| # ip address 192.168.0.61. The client id is derived from the prefix |
| # ff:00:00:00:00:00:02:00:00:02:c9:00 and the last 8 pairs of |
| # hex digits of the hardware address. |
| #dhcp-host=id:ff:00:00:00:00:00:02:00:00:02:c9:00:f4:52:14:03:00:28:05:81,192.168.0.61 |
| |
| # Always give the host with client identifier "marjorie" |
| # the IP address 192.168.0.60 |
| #dhcp-host=id:marjorie,192.168.0.60 |
| |
| # Enable the address given for "judge" in /etc/hosts |
| # to be given to a machine presenting the name "judge" when |
| # it asks for a DHCP lease. |
| #dhcp-host=judge |
| |
| # Never offer DHCP service to a machine whose Ethernet |
| # address is 11:22:33:44:55:66 |
| #dhcp-host=11:22:33:44:55:66,ignore |
| |
| # Ignore any client-id presented by the machine with Ethernet |
| # address 11:22:33:44:55:66. This is useful to prevent a machine |
| # being treated differently when running under different OS's or |
| # between PXE boot and OS boot. |
| #dhcp-host=11:22:33:44:55:66,id:* |
| |
| # Send extra options which are tagged as "red" to |
| # the machine with Ethernet address 11:22:33:44:55:66 |
| #dhcp-host=11:22:33:44:55:66,set:red |
| |
| # Send extra options which are tagged as "red" to |
| # any machine with Ethernet address starting 11:22:33: |
| #dhcp-host=11:22:33:*:*:*,set:red |
| |
| # Give a fixed IPv6 address and name to client with |
| # DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2 |
| # Note the MAC addresses CANNOT be used to identify DHCPv6 clients. |
| # Note also the they [] around the IPv6 address are obligatory. |
| #dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5] |
| |
| # Ignore any clients which are not specified in dhcp-host lines |
| # or /etc/ethers. Equivalent to ISC "deny unknown-clients". |
| # This relies on the special "known" tag which is set when |
| # a host is matched. |
| #dhcp-ignore=tag:!known |
| |
| # Send extra options which are tagged as "red" to any machine whose |
| # DHCP vendorclass string includes the substring "Linux" |
| #dhcp-vendorclass=set:red,Linux |
| |
| # Send extra options which are tagged as "red" to any machine one |
| # of whose DHCP userclass strings includes the substring "accounts" |
| #dhcp-userclass=set:red,accounts |
| |
| # Send extra options which are tagged as "red" to any machine whose |
| # MAC address matches the pattern. |
| #dhcp-mac=set:red,00:60:8C:*:*:* |
| |
| # If this line is uncommented, dnsmasq will read /etc/ethers and act |
| # on the ethernet-address/IP pairs found there just as if they had |
| # been given as --dhcp-host options. Useful if you keep |
| # MAC-address/host mappings there for other purposes. |
| #read-ethers |
| |
| # Send options to hosts which ask for a DHCP lease. |
| # See RFC 2132 for details of available options. |
| # Common options can be given to dnsmasq by name: |
| # run "dnsmasq --help dhcp" to get a list. |
| # Note that all the common settings, such as netmask and |
| # broadcast address, DNS server and default route, are given |
| # sane defaults by dnsmasq. You very likely will not need |
| # any dhcp-options. If you use Windows clients and Samba, there |
| # are some options which are recommended, they are detailed at the |
| # end of this section. |
| |
| # Override the default route supplied by dnsmasq, which assumes the |
| # router is the same machine as the one running dnsmasq. |
| #dhcp-option=3,1.2.3.4 |
| |
| # Do the same thing, but using the option name |
| #dhcp-option=option:router,1.2.3.4 |
| |
| # Override the default route supplied by dnsmasq and send no default |
| # route at all. Note that this only works for the options sent by |
| # default (1, 3, 6, 12, 28) the same line will send a zero-length option |
| # for all other option numbers. |
| #dhcp-option=3 |
| |
| # Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5 |
| #dhcp-option=option:ntp-server,192.168.0.4,10.10.0.5 |
| |
| # Send DHCPv6 option. Note [] around IPv6 addresses. |
| #dhcp-option=option6:dns-server,[1234::77],[1234::88] |
| |
| # Send DHCPv6 option for namservers as the machine running |
| # dnsmasq and another. |
| #dhcp-option=option6:dns-server,[::],[1234::88] |
| |
| # Ask client to poll for option changes every six hours. (RFC4242) |
| #dhcp-option=option6:information-refresh-time,6h |
| |
| # Set option 58 client renewal time (T1). Defaults to half of the |
| # lease time if not specified. (RFC2132) |
| #dhcp-option=option:T1,1m |
| |
| # Set option 59 rebinding time (T2). Defaults to 7/8 of the |
| # lease time if not specified. (RFC2132) |
| #dhcp-option=option:T2,2m |
| |
| # Set the NTP time server address to be the same machine as |
| # is running dnsmasq |
| #dhcp-option=42,0.0.0.0 |
| |
| # Set the NIS domain name to "welly" |
| #dhcp-option=40,welly |
| |
| # Set the default time-to-live to 50 |
| #dhcp-option=23,50 |
| |
| # Set the "all subnets are local" flag |
| #dhcp-option=27,1 |
| |
| # Send the etherboot magic flag and then etherboot options (a string). |
| #dhcp-option=128,e4:45:74:68:00:00 |
| #dhcp-option=129,NIC=eepro100 |
| |
| # Specify an option which will only be sent to the "red" network |
| # (see dhcp-range for the declaration of the "red" network) |
| # Note that the tag: part must precede the option: part. |
| #dhcp-option = tag:red, option:ntp-server, 192.168.1.1 |
| |
| # The following DHCP options set up dnsmasq in the same way as is specified |
| # for the ISC dhcpcd in |
| # http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.txt |
| # adapted for a typical dnsmasq installation where the host running |
| # dnsmasq is also the host running samba. |
| # you may want to uncomment some or all of them if you use |
| # Windows clients and Samba. |
| #dhcp-option=19,0 # option ip-forwarding off |
| #dhcp-option=44,0.0.0.0 # set netbios-over-TCP/IP nameserver(s) aka WINS server(s) |
| #dhcp-option=45,0.0.0.0 # netbios datagram distribution server |
| #dhcp-option=46,8 # netbios node type |
| |
| # Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave. |
| #dhcp-option=252,"\n" |
| |
| # Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP client |
| # probably doesn't support this...... |
| #dhcp-option=option:domain-search,eng.apple.com,marketing.apple.com |
| |
| # Send RFC-3442 classless static routes (note the netmask encoding) |
| #dhcp-option=121,192.168.1.0/24,1.2.3.4,10.0.0.0/8,5.6.7.8 |
| |
| # Send vendor-class specific options encapsulated in DHCP option 43. |
| # The meaning of the options is defined by the vendor-class so |
| # options are sent only when the client supplied vendor class |
| # matches the class given here. (A substring match is OK, so "MSFT" |
| # matches "MSFT" and "MSFT 5.0"). This example sets the |
| # mtftp address to 0.0.0.0 for PXEClients. |
| #dhcp-option=vendor:PXEClient,1,0.0.0.0 |
| |
| # Send microsoft-specific option to tell windows to release the DHCP lease |
| # when it shuts down. Note the "i" flag, to tell dnsmasq to send the |
| # value as a four-byte integer - that's what microsoft wants. See |
| # http://technet2.microsoft.com/WindowsServer/en/library/a70f1bb7-d2d4-49f0-96d6-4b7414ecfaae1033.mspx?mfr=true |
| #dhcp-option=vendor:MSFT,2,1i |
| |
| # Send the Encapsulated-vendor-class ID needed by some configurations of |
| # Etherboot to allow is to recognise the DHCP server. |
| #dhcp-option=vendor:Etherboot,60,"Etherboot" |
| |
| # Send options to PXELinux. Note that we need to send the options even |
| # though they don't appear in the parameter request list, so we need |
| # to use dhcp-option-force here. |
| # See http://syslinux.zytor.com/pxe.php#special for details. |
| # Magic number - needed before anything else is recognised |
| #dhcp-option-force=208,f1:00:74:7e |
| # Configuration file name |
| #dhcp-option-force=209,configs/common |
| # Path prefix |
| #dhcp-option-force=210,/tftpboot/pxelinux/files/ |
| # Reboot time. (Note 'i' to send 32-bit value) |
| #dhcp-option-force=211,30i |
| |
| # Set the boot filename for netboot/PXE. You will only need |
| # this is you want to boot machines over the network and you will need |
| # a TFTP server; either dnsmasq's built in TFTP server or an |
| # external one. (See below for how to enable the TFTP server.) |
| #dhcp-boot=pxelinux.0 |
| |
| # The same as above, but use custom tftp-server instead machine running dnsmasq |
| #dhcp-boot=pxelinux,server.name,192.168.1.100 |
| |
| # Boot for iPXE. The idea is to send two different |
| # filenames, the first loads iPXE, and the second tells iPXE what to |
| # load. The dhcp-match sets the ipxe tag for requests from iPXE. |
| #dhcp-boot=undionly.kpxe |
| #dhcp-match=set:ipxe,175 # iPXE sends a 175 option. |
| #dhcp-boot=tag:ipxe,http://boot.ipxe.org/demo/boot.php |
| |
| # Encapsulated options for iPXE. All the options are |
| # encapsulated within option 175 |
| #dhcp-option=encap:175, 1, 5b # priority code |
| #dhcp-option=encap:175, 176, 1b # no-proxydhcp |
| #dhcp-option=encap:175, 177, string # bus-id |
| #dhcp-option=encap:175, 189, 1b # BIOS drive code |
| #dhcp-option=encap:175, 190, user # iSCSI username |
| #dhcp-option=encap:175, 191, pass # iSCSI password |
| |
| # Test for the architecture of a netboot client. PXE clients are |
| # supposed to send their architecture as option 93. (See RFC 4578) |
| #dhcp-match=peecees, option:client-arch, 0 #x86-32 |
| #dhcp-match=itanics, option:client-arch, 2 #IA64 |
| #dhcp-match=hammers, option:client-arch, 6 #x86-64 |
| #dhcp-match=mactels, option:client-arch, 7 #EFI x86-64 |
| |
| # Do real PXE, rather than just booting a single file, this is an |
| # alternative to dhcp-boot. |
| #pxe-prompt="What system shall I netboot?" |
| # or with timeout before first available action is taken: |
| #pxe-prompt="Press F8 for menu.", 60 |
| |
| # Available boot services. for PXE. |
| #pxe-service=x86PC, "Boot from local disk" |
| |
| # Loads <tftp-root>/pxelinux.0 from dnsmasq TFTP server. |
| #pxe-service=x86PC, "Install Linux", pxelinux |
| |
| # Loads <tftp-root>/pxelinux.0 from TFTP server at 1.2.3.4. |
| # Beware this fails on old PXE ROMS. |
| #pxe-service=x86PC, "Install Linux", pxelinux, 1.2.3.4 |
| |
| # Use bootserver on network, found my multicast or broadcast. |
| #pxe-service=x86PC, "Install windows from RIS server", 1 |
| |
| # Use bootserver at a known IP address. |
| #pxe-service=x86PC, "Install windows from RIS server", 1, 1.2.3.4 |
| |
| # If you have multicast-FTP available, |
| # information for that can be passed in a similar way using options 1 |
| # to 5. See page 19 of |
| # http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf |
| |
| |
| # Enable dnsmasq's built-in TFTP server |
| #enable-tftp |
| |
| # Set the root directory for files available via FTP. |
| #tftp-root=/var/ftpd |
| |
| # Do not abort if the tftp-root is unavailable |
| #tftp-no-fail |
| |
| # Make the TFTP server more secure: with this set, only files owned by |
| # the user dnsmasq is running as will be send over the net. |
| #tftp-secure |
| |
| # This option stops dnsmasq from negotiating a larger blocksize for TFTP |
| # transfers. It will slow things down, but may rescue some broken TFTP |
| # clients. |
| #tftp-no-blocksize |
| |
| # Set the boot file name only when the "red" tag is set. |
| #dhcp-boot=tag:red,pxelinux.red-net |
| |
| # An example of dhcp-boot with an external TFTP server: the name and IP |
| # address of the server are given after the filename. |
| # Can fail with old PXE ROMS. Overridden by --pxe-service. |
| #dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3 |
| |
| # If there are multiple external tftp servers having a same name |
| # (using /etc/hosts) then that name can be specified as the |
| # tftp_servername (the third option to dhcp-boot) and in that |
| # case dnsmasq resolves this name and returns the resultant IP |
| # addresses in round robin fashion. This facility can be used to |
| # load balance the tftp load among a set of servers. |
| #dhcp-boot=/var/ftpd/pxelinux.0,boothost,tftp_server_name |
| |
| # Set the limit on DHCP leases, the default is 150 |
| #dhcp-lease-max=150 |
| |
| # The DHCP server needs somewhere on disk to keep its lease database. |
| # This defaults to a sane location, but if you want to change it, use |
| # the line below. |
| #dhcp-leasefile=/var/lib/misc/dnsmasq.leases |
| |
| # Set the DHCP server to authoritative mode. In this mode it will barge in |
| # and take over the lease for any client which broadcasts on the network, |
| # whether it has a record of the lease or not. This avoids long timeouts |
| # when a machine wakes up on a new network. DO NOT enable this if there's |
| # the slightest chance that you might end up accidentally configuring a DHCP |
| # server for your campus/company accidentally. The ISC server uses |
| # the same option, and this URL provides more information: |
| # http://www.isc.org/files/auth.html |
| #dhcp-authoritative |
| |
| # Run an executable when a DHCP lease is created or destroyed. |
| # The arguments sent to the script are "add" or "del", |
| # then the MAC address, the IP address and finally the hostname |
| # if there is one. |
| #dhcp-script=/bin/echo |
| |
| # Set the cachesize here. |
| #cache-size=150 |
| |
| # If you want to disable negative caching, uncomment this. |
| #no-negcache |
| |
| # Normally responses which come from /etc/hosts and the DHCP lease |
| # file have Time-To-Live set as zero, which conventionally means |
| # do not cache further. If you are happy to trade lower load on the |
| # server for potentially stale date, you can set a time-to-live (in |
| # seconds) here. |
| #local-ttl= |
| |
| # If you want dnsmasq to detect attempts by Verisign to send queries |
| # to unregistered .com and .net hosts to its sitefinder service and |
| # have dnsmasq instead return the correct NXDOMAIN response, uncomment |
| # this line. You can add similar lines to do the same for other |
| # registries which have implemented wildcard A records. |
| #bogus-nxdomain=64.94.110.11 |
| |
| # If you want to fix up DNS results from upstream servers, use the |
| # alias option. This only works for IPv4. |
| # This alias makes a result of 1.2.3.4 appear as 5.6.7.8 |
| #alias=1.2.3.4,5.6.7.8 |
| # and this maps 1.2.3.x to 5.6.7.x |
| #alias=1.2.3.0,5.6.7.0,255.255.255.0 |
| # and this maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40 |
| #alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0 |
| |
| # Change these lines if you want dnsmasq to serve MX records. |
| |
| # Return an MX record named "maildomain.com" with target |
| # servermachine.com and preference 50 |
| #mx-host=maildomain.com,servermachine.com,50 |
| |
| # Set the default target for MX records created using the localmx option. |
| #mx-target=servermachine.com |
| |
| # Return an MX record pointing to the mx-target for all local |
| # machines. |
| #localmx |
| |
| # Return an MX record pointing to itself for all local machines. |
| #selfmx |
| |
| # Change the following lines if you want dnsmasq to serve SRV |
| # records. These are useful if you want to serve ldap requests for |
| # Active Directory and other windows-originated DNS requests. |
| # See RFC 2782. |
| # You may add multiple srv-host lines. |
| # The fields are <name>,<target>,<port>,<priority>,<weight> |
| # If the domain part if missing from the name (so that is just has the |
| # service and protocol sections) then the domain given by the domain= |
| # config option is used. (Note that expand-hosts does not need to be |
| # set for this to work.) |
| |
| # A SRV record sending LDAP for the example.com domain to |
| # ldapserver.example.com port 389 |
| #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389 |
| |
| # A SRV record sending LDAP for the example.com domain to |
| # ldapserver.example.com port 389 (using domain=) |
| #domain=example.com |
| #srv-host=_ldap._tcp,ldapserver.example.com,389 |
| |
| # Two SRV records for LDAP, each with different priorities |
| #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1 |
| #srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2 |
| |
| # A SRV record indicating that there is no LDAP server for the domain |
| # example.com |
| #srv-host=_ldap._tcp.example.com |
| |
| # The following line shows how to make dnsmasq serve an arbitrary PTR |
| # record. This is useful for DNS-SD. (Note that the |
| # domain-name expansion done for SRV records _does_not |
| # occur for PTR records.) |
| #ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services" |
| |
| # Change the following lines to enable dnsmasq to serve TXT records. |
| # These are used for things like SPF and zeroconf. (Note that the |
| # domain-name expansion done for SRV records _does_not |
| # occur for TXT records.) |
| |
| #Example SPF. |
| #txt-record=example.com,"v=spf1 a -all" |
| |
| #Example zeroconf |
| #txt-record=_http._tcp.example.com,name=value,paper=A4 |
| |
| # Provide an alias for a "local" DNS name. Note that this _only_ works |
| # for targets which are names from DHCP or /etc/hosts. Give host |
| # "bert" another name, bertrand |
| #cname=bertand,bert |
| |
| # For debugging purposes, log each DNS query as it passes through |
| # dnsmasq. |
| #log-queries |
| |
| # Log lots of extra information about DHCP transactions. |
| #log-dhcp |
| |
| # Include another lot of configuration options. |
| #conf-file=/etc/dnsmasq.more.conf |
| #conf-dir=/etc/dnsmasq.d |
| |
| # Include all the files in a directory except those ending in .bak |
| #conf-dir=/etc/dnsmasq.d,.bak |
| |
| # Include all files in a directory which end in .conf |
| #conf-dir=/etc/dnsmasq.d/,*.conf |